USER’S MANUAL PATIO HEATER NP10129 THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Please give us a chance to make it right and do better！ Contact our friendly customer service department for help first.
Contact Us! Do NOT return this item. Contact our friendly customer service department for help first. E-mail US: cs.us@costway.com UK: cs.uk@costway.com Before You Start Please read all instructions carefully. Retain instructions for future reference. Separate and count all parts and hardware. Read through each step carefully and follow the proper order.
DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department. WARNING Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
WARNING Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operation and maintenance instructions thoroughly before installing or servicing this equipment. R R R US ANS Z83.26-2014 • CSA 2.
PACKAGE CONTENTS A Reflector B Flame Screen C Glass Tube D Upper Support E Protective Guard F Black Silicone Ring G Side Panel H Front Panel I Gas Hose & Regulator Control Box Assy J Lower Support K Block Belt L Wheel Assembly M Bottom Plate N PART A B C D E F G H I J K DESCRIPTION Reflector Flame Screen Glass Tube Upper Support Protective Guard Black Silicone Ring Side Panel Front Panel Gas Hose & Regulator Control Box Assy Lower Support PART DESCRIPTION L Block Belt M Wheel As
HARDWARE CONTENTS (shown actual size) AA BB Small flat washer Φ6 Qty. 6 Wing nut Qty. 3 DD CC FF EE 3/16” Screw Qty. 42 Screw M5 X 12 Qty. 6 JJ II Philips screwdriver Qty. 1 LL Screw M4 X 6 Qty.1 Knob Qty. 1 NN Chain Qty.1 Wrench Qty. 1 Fixing Bracket Qty. 4 KK MM M6 Flange nut Qty.4 Bolt M6 X 12 Qty. 4 HH GG Stud Qty. 3 OO Long Stem Lighter Qty.1 06 AA Battery (1.5 V) Qty.
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. This manual contains important information about the assembly, operation and maintenance of this patio heater. General safety information is presented in these first few pages and is also located throughout the manual. Keep this manual for future reference and to educate new users of this product. This manual should be read in conjunction with the labeling on the product.
SAFETY INFORMATION DANGER • EXPLOSION - FIRE HAZARD • Keep solid combustibles, such as building materials, paper or cardboard, a safe distance away from the heater as recommended by the instructions. • Provide adequate clearances around air openings into the combustion chamber. • Never use the heater in spaces which do or may contain volatile or airborne combustibles, or products such as gasoline, solvents, paint thinner, dust particles or unknown chemicals.
WARNING We cannot foresee every use which may be made of our heaters. Check with your local fire safety authority if you have questions about heater use. Other standards govern the use of fuel gases and heat producing products for specific uses. Your local authorities can advise you about these. If no local codes exist, follow National Fuel Gas Code, ANS Z223.1. In Canada, installation must conform to local codes. If no local codes exist, follow the current National standards of CANADA CAN/CGA-B 149.2.
WARNING Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance. WARNING: For Outdoor Use Only DANGER CARBON MONOXIDE HAZARD This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you. Never use this appliance in an enclosed space such as a camper, tent, car or home.
WARNING Certain materials or items, when stored under the heater, will be subjected to radiant heat and could be seriously damaged. CAUTION SERVICE SAFETY • Keep all connections and fittings clean. Make sure propane cylinder valve outlet is clean. • During set up, check all connections and fittings for leaks using soapy water. Never use a flame. • Use as a heating appliance only. Never alter in any way or use with any device.
WARNING • Alert children and adults to the hazards of high surface temperatures. Stay away from these surfaces to avoid burning skin or igniting clothing. • Carefully supervise young children when in the vicinity of the heater. • Do not hang clothing or any other flammable materials from the heater, or place on or near the heater. • Replace any guard or protective device removed for servicing the appliance prior to placing back in service.
ASSEMBLY INSTRUCTIONS 1. Assemble the wheel assembly (M) to the bottom plate(N). Fix the wheel assembly to the bottom plate using 4pcs bolt M6 x 12(EE) and 4pcs flange nut M6 (FF). 1 Hardware Used EE Bolt M6 X 12 x4 FF M6 Flange nut x4 II Wrench x1 EE N M FF 2-1. Unscrew the switch button, load small battery, tighten the switch button. 2-2. Insert the pins of the base to the holes of lower support (K), press to secure the pins.
3. Assemble block belt. Fix the block belt (L) to the 2pcs of lower support behind the front door, using 2pcs screw M5X12. 3 Hardware Used GG Screw M5 X 12 JJ Philips screwdriver x2 x1 L GG 4. Assemble the Upper support. Insert the 4pcs upper support (D) to the lower support (K). Secure them with 8pcs screw 3/16”.
5. Assemble the flame screen (B) to the upper support (D). Secure the flame screen to the upper support using 8pcs screw 3/16”(DD). 5 B Hardware Used DD 3/16” Screw x8 JJ Philips screwdriver x1 DD D 6. Assemble the reflector (A) onto the flame screen (B). Screw the 3pcs stud (CC) on the flame screen, put 3pcs washer Φ6 (BB) onto the top of stud, then put the reflector onto the stud, secure them with 3pcs washer Φ6 and 3pcs wing nut (AA).
7. Carefully install the glass tube by lifting up and inserting through the center hole in the upper plate. Ensure the black silicone ring is attached to the lower edge of the glass tube as illustrated. Slide the glass tube through the hole of the lower plate cover and onto the control box assembly. Check and ensure that the glass tube is positioned properly and is completely covering the center hole of the control box assembly.
9. Attach the three side panels (G) to the heater using 18pcs screw 3/16”. Note : Do not cover the front side where the control knob is. 9 Hardware Used DD 3/16” Screw x 18 JJ Philips screwdriver x1 DD G 10. Install the knob (KK) to M4x6 screw (LL). Hang the chain (MM) to the hole on the control box assy and put the pothook of front panel (H) to the holes of bottom plate.
11. Screw gas hose and regulator to propane cylinder (not included). Do not cross-thread. Every part of the heater shall be secure against displacement and shall be constructed to maintain a fixed relationship between essential parts under normal and reasonable conditions of handling and usage. Parts not permanently secured shall be designed so they cannot be incorrectly assembled and cannot be improperly located or misaligned in removing or replacing during cleaning or other servicing.
17.9 in. / 45.5cm A dented, rusted or damaged propane cylinder may be hazardous and should be checked by your cylinder supplier. Never use a propane cylinder with a damaged valve connection. The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT) or the standard for cylinders, spheres and tubes for transportation of dangerous goods and commission, CAN/CSA-B339.
OPERATION INSTRUCTIONS Leak Check WARNING • Perform all leak tests outdoors. • Extinguish all open flames. • NEVER perform a leak test when smoking. • Do not use the heater until all connections have been leak tested and do not leak. Hose / Regulator connection Regulator / Cylinder connection 1. Make 2-3 oz. of leak check solution (one part liquid dishwashing detergent and three parts water). 2. Apply several drops of solution where hose attaches to regulator. 3.
DANGER • CARBON MONOXIDE HAZARD • For outdoor use only. Never use inside house, or other unventilated or enclosed areas. This heater consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life. Caution: Do not attempt to operate until you have read and understand all General Safety Information in this manual and all assembly is complete and leak checks have been performed.
Igniter Figure 1 Variable control knob Figure 2 4. Push and release the igniter button until pilot flame is visible through the glass tube. 5. Once the pilot is lit, continue to depress the control knob for 30 seconds. 6. If the pilot does not stay lit, repeat steps 4 to 6. 7. If after repeating steps 4 to 6 unit does not light, then -Push in control knob and turn counterclockwise to “PILOT” (Figure 3).
8. Push in and turn the control knob to the “HIGH”, then release control knob. If you want a lower temperature, push in the control knob and turn counterclockwise to the “LOW” (Figure 5). Note: Improper operation, can cause injury or property damage. If pilot fails to remain lit, all valves should be closed and a waiting period of at least 5 minutes should pass before attempting to light. If you experience any ignition problem please consult “Troubleshooting” section.
WARNING FOR YOUR SAFETY Heater will be hot after use. Handle with extreme care. Shut Down: 1. Turn control knob clockwise to PILOT. (Normally, burner will make a slight popping sound when extinguished.) Burner will extinguish but PILOT will remain ON. 2. To extinguish PILOT depress control knob and continue to turn it clockwise to OFF. 3. Turn cylinder valve clockwise to OFF and disconnect regulator when heater is not in use. Note: After use, some discoloration of the emitter screen is normal.
CARE AND MAINTENANCE WARNING FOR YOUR SAFETY: • Do NOT touch or move heater for at least 45 minutes after use. • Reflector is hot to the touch. • Allow reflector to cool before touching. To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis: Keep exterior surfaces clean. 1. Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents. 2.
TIP: Use high-quality automobile wax to help maintain the appearance of your heater. Apply to exterior surfaces from the pole down. Do not apply to emitter screen or domes. Storage Between uses: Turn Control Knob OFF. Disconnect LP cylinder. Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris). If desired, cover heater to protect exterior surfaces and to help prevent build-up in air passages.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Cylinder valve is closed Open valve Blockage in orifice or pilot tube Pilot won’t light Air in gas line Note: Heater operates Low gas pressure with cylinder valve fully open at reduced efficiency below 40ºF (5ºC) Igniter fails Pilot won’t stay lit Burner won’t light Burner flame is low Clean or replace orifice or pilot tube Open gas line and bleed it (pressing control knob in) for not more than 1 - 2 minutes or until you smell gas Turn cyl
Welcome to visit our website and purchase our quality products! With your inspiring rating, COSTWAY will be more consistent to offer you EASY SHOPPING EXPERIENCE, GOOD PRODUCTS and EFFICIENT SERVICE! US office: Fontana, California UK office: Ipswich Reward Points Exclusive Customer Service Permanent Shopping Cart Order History this product and giving us valuable feedbacks.
