Instruction Manual

ManualsBrandsCosmo ManualsAppliancesCOS-30BIMTK Built in Microwave Trim Kit for COS-BIM22SSB

MICROWAVE OVEN BUILT-IN TRIM

KIT INSTALLATION INSTRUCTIONS

listed

for use over any electric or gas built-in oven, up to 30" (76.2 cm) wide

MICROWAVE OVEN SAFETY

Table of Contents

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

Built-In Trim Kit Models COS-30BIMTK (fits COS-BIM22SSB)

MICROWAVE OVEN SAFETY ..................................................1

INSTALLATION INSTRUCTIONS.............................................2

Tools and Parts ......................................................................2

Location Requirements..........................................................2

Required Cutout Dimensions.................................................2

Trim Kit Frame Dimensions....................................................2

Electrical Requirements .........................................................3

Prepare Microwave Oven.......................................................3

Prepare Cutout/Cabinet Opening..........................................3

Install the Microwave Oven....................................................4

Install Trim Kit Frame .............................................................5

Summary of content (6 pages)

PAGE 1
Built-In Trim Kit Models COS-30BIMTK (fits COS-BIM22SSB) MICROWAVE OVEN BUILT-IN TRIM KIT INSTALLATION INSTRUCTIONS UL listed for use over any electric or gas built-in oven, up to 30" (76.2 cm) wide Table of Contents MICROWAVE OVEN SAFETY ..................................................1 INSTALLATION INSTRUCTIONS.............................................2 Tools and Parts ......................................................................2 Location Requirements .....................................
PAGE 2
INSTALLATION INSTRUCTIONS Tools and Parts Required Cutout Dimensions Tools Needed 22³⁄₄" (57.8 cm) Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. ■ ■ ■ Measuring tape Pencil Phillips screwdriver Drill 7/64" drill bit ■ ■ 1¹⁄₁₆" (2.7 cm) htdiW 17" (43.2 cm) min. 17¹⁄₈" (43.5 cm) max. Parts Supplied (not shown to scale) A 25¹⁄₂" (64.8 cm) 1¹⁄₁₆" (2.7 cm) 3" (7.6 cm) B A. Trim kit frame overhang B.
PAGE 3
Electrical Requirements WARNING Electrical Shock Hazard Prepare Microwave Oven 1. Unplug microwave oven before proceeding with installation. 2. Remove any loose items inside microwave oven. 3. Gently turn microwave oven onto its top, with the door facing forward (toward installer). 4. Align the #33 holes on the microwave oven bottom with the #33 holes on the rails, as shown, making sure the flanges are forward and pointing up. A B C Plug into a grounded 3 prong outlet. Do not remove ground prong.
PAGE 4
3. Align the center arrows on the bottom duct with the centerline drawn in Step 1 above. Install the Microwave Oven 1. Gently return microwave oven to its upright position. 2. Position microwave oven near cutout opening. WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. A B A. Bottom duct B. Center arrows, aligned with centerline 4. Mark the three mounting holes through the bottom duct onto the cutout floor. Do not use an adapter.
PAGE 5
. Slide the microwave oven back and into place. The mounting holes of the rail flanges and bottom duct flange will align against the bottom front facing of the cutout/cabinet opening. 6. Secure the microwave oven to the cutout/cabinet by installing four short screws into the mounting holes. 2. Holding the trim kit frame in place, use 7/64" drill to drill four pilot holes into the front facing of the cutout/cabinet through the mounting hole guides in the upper and lower corners of the trim kit frame.
PAGE 6
WARRANTY AND SERVICE For full warranty details on this product please visit: http://www.cosmoappliances.com/warranty TO RECEIVE WARRANTY SERVICE, YOUR PRODUCT MUST BE REGISTERED. TO REGISTER, VISIT: WWW.COSMOAPPLIANCES.