Installation Guide

TROUBLESHOOTING GUIDE
3
OVEN PROBLEM POSSIBLE CAUSES AND/OR REMEDY
Range does not function
Range is not connected to electrical power. Ask a professional to check power
circuit breaker, wiring and fuses.
Broil does not work
Temperature control knob is rotated too far past broil position (500° F); PRE
HEATING indicator will light intermittently
Door does not open
Oven is still in self-clean mode. Door latch will release when safe temperature
is reached.
Oven light does not work
Light bulb is burned out. Range is not connected to power/ clean is cycle on
Igniters does not work
Circuit is tripped. Fuse is blown. Range is not connected to power.
Igniters sparking taut no flame ignition Gas supply valve is in "OFF" position. Gas supply is interrupted.
igniters spark continuously after flame
ignition
ignition micro-switches remain Incorrectly engaged; call a qualified technician
for repair.
Burner ignites but flame is targe,
distorted, or yellow
Burner ports are clogged. Unit is not set to the appropriate gas type. Call a
qualified technician for gas conversion procedure.
Oven door is locked and will not
release, even after cooling
Turn the oven off at the circuit breaker and wait 5 minutes. Turn breaker back
on. The oven should reset itself and will be operable.
Oven is not heating
Check the circuit breaker or fuse box to your house. Make sure there is
proper electrical power to the oven. Make sure the oven temperature has
been selected.
Oven light is not working properly Replace or reinsert the light bulb if loose or defective.
Oven light stays on Check for obstruction in oven door, Check to see if hinge is bent.
Cannot remove lens cover on light
There may be soil build-up around the lens cover. Wipe lens cover area with a
clean dry towel prior to attempting to remove the lens cover.
PRE-HEATING indicator lights up
intermittently and sound alarm on
This is a FAULT alarm indicating the failure of the cooling fan/s. Try resetting
by turning both selectors to the OFF position. If the error is not repaired, call a
qualified technician for diagnosis and repair. If not repaired, this error
indicator will appear again within 10 seconds once the oven is activated in
any functions for which cooling fans are required to operate, preventing the
use of the oven. Set both selectors to OFF position and call a qualified
technician for repair.
HEATING indicator light turned on
intermittently and with sound alarm on
This is a FAULT indicating failure of the oven sensor temperature probe; in
this case cooling fans will start automatically. To reset, switch both selector to
the OFF position. To stop buzzer and light indicator, disconnect the appliance
from the main electrical supply and call a qualified technician for repair.
CLEAN indicator light on intermittently
and sound alarm on
Electrical power failure happening during cleaning cycle operation, cleaning
cycle interrupted; cooling fans remains both activated; the error will be reset
by putting two selectors in OFF positron; repeat cleaning cycle if needed after
3-4 hours.
CLEAN indicator tight turned on
Interruption/Stop of an incomplete cleaning cycle due to a intentional or
Light bulb is burned out. Range is not connected to power/ clean is cycle on
Circuit is tripped. Fuse is blown. Range is not connected to power.
intermittently, sound alarm off
accidental displacement of one of the two oven selectors from CLEAN
position during cleaning cycle operation; put both selectors in OFF position,
wait that door latch unlocks the door when oven temperature is dropped
below 500° F{260° C) and then re-select a desired oven function.
PRE-HEATING indicator light on
intermittently, sound alarm on
Wrong temperature knob selection in oven functions BROILER or
CONVECTION BROILER (temperature knob positioned not at 500°F
position, over Tmax or under 450°F position); select OFF position and then
500°F on temperature selector;
Or
Wrong temperature knob selection for oven functions BAKE,
CONVECTION BAKE; TURBO, CONVECTION (temperature knob
positioned over Tmax=500°F position); select OFF position and then the
desired temperature under Tmax position on temperature selector.