WALL OVEN COS-30ESWC COS-30EDWC 30 IN. ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. FOR RESIDENTIAL USE ONLY. INSTALLER: PLEASE LEAVE THESE INSTRUCTIONS WITH THIS UNIT FOR THE OWNER. OWNER: PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. Rev.23.
THANK YOU FOR YOUR PURCHASE Thank you for your purchase. We know that you have many brands and products to choose from and we are honored to know that you have decided to take one of our products into your home and hope that you enjoy it. COSMO Appliances are designed according to the strictest safety and performance standard for the North American market. We follow the most advanced manufacturing philosophy. Each appliance leaves the factory after thorough quality inspection and testing.
TABLE OF CONTENTS OVEN SAFETY.................................................................................................. 4 Important Safety Instructions ............................................................................. 6 INSTALLATION REQUIREMENTS...................................................................... 7 Tools and Parts...................................................................................................... 7 Location Requirements.................................
OVEN SAFETY READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "WARNING" or "CAUTION.
WARNING • This appliance is intended for normal residential use. It is not approved for commercial use, outdoor installation, or any other application not specifically allowed by this manual. • This appliance requires connection to a 3-prong or 4-prong, 240VAC single-phase (split-phase), 60Hz grounded electrical source.
IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire, electrical shock, injury to persons, or damage when using the appliance, follow basic precautions, including the following: • Proper Installation – The appliance, when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or the Canadian Electrical Code, CSA C22.1-02.
INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
Parts Supplied Oven Racks Single oven model (2) Double oven model (3) Oven door handle Single oven model (1) Double oven model (2) 2-Piece broiler pan Meat thermometer (probe) #8-14 x 1" Mounting screws Single oven model (2) Double oven model (4) NOTE: • To purchase these replacement parts or any other accessories, please visit www.cosmoappliances.com or reference the contact information at the end of this manual.
LOCATION REQUIREMENTS IMPORTANT: Observe all governing codes and ordinances. • Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance with oven. • Recessed installation area must provide complete enclosure around the recessed portion of the oven. • Oven support surface must be solid, level and flush with bottom of cabinet cutout. • Floor must be able to support a single oven weight of 130 lbs (59 kg) plus food load of 30 lbs (14 kg).
PRODUCT DIMENSIONS Single Oven Model Dimensions Letter Double Oven Model Measurements Single Oven Model Double Oven Model Width (Overall) A 29 13/16" (75.8 cm) 29 13/16" (75.8 cm) Depth (Overall) B 24 5/16" (61.8 cm) 24 5/16" (61.8 cm) Height (Overall) C 28 7/16" (72.2 cm) 51 3/16" (130.0 cm) Width (Recessed) D 28 1/2" (72.4 cm) 28 1/2" (72.4 cm) Depth (Recessed) E 23 5/16" (59.2 cm) 23 5/16" (59.2 cm) Height (Recessed) F 27 3/16" (69.1 cm) 49 15/16" (126.
CUTOUT DIMENSIONS IMPORTANT: Some cabinet and building materials are not designed to withstand the heat produced by the oven for baking and self-cleaning. Check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. GIVEN DIMENSIONS ARE MINIMUM CLEARANCES.
Double Oven in Cabinet D 4" Electrical Junction Box Location B A C E D F Dimensions Letter Double Oven Measurements Cabinet Width (Cutout) A 28 5/8" (72.7 cm) Depth (Cutout) B 23 13/16" (60.5 cm) Height (Cutout) C 50 1/4" (127.7 cm) Clearance to Upper/ Lower Cabinet Door D 1 1/2" (3.8 cm) Oven Side Overlap E 11/16" (1.7 cm) Cutout to Floor (Recommended) F 14 3/4" (37.5 cm) NOTE: • If the cabinet does not have a front frame and the sides are less than 3/4" (1.
ELECTRICAL REQUIREMENTS WARNING ELECTRICAL SHOCK HAZARD • Do not use an extension cord with this appliance. • Remove house fuse or open circuit breaker before beginning installation. • Improper connection of aluminum house wiring to copper leads can result in an electrical hazard or fire. Use only connectors designed for joining copper to aluminum and follow the manufacturer’s recommended procedure closely. ELECTRICAL GROUNDING INSTRUCTIONS • This appliance must be properly grounded.
CANADA ONLY Be sure that the electrical connection and wire size are adequate and in conformance with the CSA Standard C22.1, Canadian Electrical Code, Part 1 latest edition and all local codes and ordinances. A copy of the above code standards can be obtained from: Canadian Standards Association 178 Rexdale Blvd.
• A single-phase (split-phase), 3-wire or 4-wire, 120/208 VAC or 120/240 VAC, 60 hertz electrical system must be used. It is the personal responsibility of the oven owner to provide the correct electrical service for this oven. • Effective January 1, 1996, the National Electrical Code requires that new construction (not existing) utilize a 4-conductor connection to an electric oven.
UNPACK OVEN WARNING EXCESSIVE WEIGHT HAZARD • Use two or more people to move and install oven. Failure to do so can result in back or other injury. 1. Remove all tape and packaging materials from around the oven. 2. Open the oven door and remove packaging materials and oven racks inside the oven. 3. Check for film on stainless steel parts, padding/spacers on and around door and face of oven, cardboard and plastic on and around racks, etc.
REMOVE OVEN DOOR IMPORTANT: The oven door is heavy and fragile, and the door front is glass. To avoid oven door glass breakage, use both hands, and grasp only the sides of the oven door to remove. Do not lift oven door by door handle. 1. Fully open the oven door. 2. Unlock the hinge locks on both sides, rotating them as far toward the open door frame as they will go. Locked Unlocked 3. Firmly grasp both sides of the door. 4.
ELECTRICAL CONNECTION WARNING ELECTRICAL SHOCK HAZARD • Turn off the circuit breaker or remove house fuse to the oven branch circuit before servicing. • This appliance must be properly grounded. • Do not use an adapter or an extension cord. • Failure to do so can result in death, fire, or electrical shock. WARNING EXCESSIVE WEIGHT HAZARD • Use two or more people to move and install oven. Failure to do so can result in back or other injury.
1. Turn off the circuit breaker or remove fuses to the oven branch circuit. 2. Using two or more people, grasp the ceiling of the oven cavity, lift oven on table or platform directly in front of and even with the cutout opening. • For a single oven, the platform and the cutout floor must both support 160 lbs (73 kg). • For a double oven, the platform and the cutout floor must both support 290 lbs (132 kg). 3.
3-WIRE POWER SUPPLY CONNECTION IMPORTANT: Use the 3-wire cable from power supply where local codes permit connecting the oven ground conductor to the neutral (white) junction box supply wire. 3-Wire Cable from Power Supply Junction Box Black Wires UL Listed or CSA Approved Wire Connector White Wires Red Wires Ground (Green or Bare) Wire Oven Conduit 1. Remove junction box cover, if present. 2.
4-WIRE POWER SUPPLY CONNECTION IMPORTANT: Use the 4-wire cable from power supply where local codes do not permit connecting the oven ground conductor to the neutral (white) junction box supply wire. 4-Wire Cable from Power Supply Junction Box White Wires Black Wires UL Listed or CSA Approved Wire Connector Ground (Green or Bare) Wire Red Wires Oven Conduit 1. Remove junction box cover, if present. 2.
INSTALL OVEN WARNING EXCESSIVE WEIGHT HAZARD • Use two or more people to move and install oven. Failure to do so can result in back or other injury. 1. Loop (do not tie) a 36" (91 cm) string around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven. 2. Lift oven into cabinet cutout using the oven opening as a grip. Carefully push against the oven front frame. Do not push against outside edges.
6. Secure the oven to the cabinet with mounting screws provided. NOTE: • If the cabinet is particle board, you must use 3/4" particle board screws. These may be purchased at any hardware store. INSTALL OVEN DOOR IMPORTANT: The oven door is heavy and fragile, and the door front is glass. To avoid oven door glass breakage, use both hands, and grasp only the sides of the oven door to remove. Do not lift oven door by door handle. Assembling Door 1. Verify that the hinge arms are extending forward. 2.
4. Open the door fully. If the door will not open fully, the indentation is not seated correctly in the bottom edge of the slots. 5. Lock the hinge locks, rotating them back toward the slots in the oven frame until they lock. Unlocked Locked 6. Close the oven door. Check that the door is free to open and close and is level while closed.
INSTALL OVEN DOOR HANDLE (FOR UNITS WITHOUT THE HANDLE PRE-INSTALLED) Be very careful not to scratch the surface of the unit. The appearance of the handle may vary from what is shown in the manual Tool Needed • Hex key (provided) Installing the Handle 1. Partially loosen the set screws installed in both ends of the handle with the Hex key provided. Set screw (pre-installed) 2.
COMPLETE INSTALLATION INSERT OVEN RACKS The appearance of the racks may vary from what is shown in the manual. 1. Place the end of the rack on the support. 2. Tilt the front end up and push the rack in. CHECK OPERATION OF OVEN IMPORTANT: Check that all packing material and tape have been removed. Failure to remove these materials could result in damage to the appliance once the appliance has been turned on and surfaces have heated. 1.
IMPORTANT Do Not Return This Product To The Store If you have a problem with this product, please contact COSMO Customer Support at +1 (888) 784-3108 DATED PROOF OF PURCHASE, MODEL #, AND SERIAL # REQUIRED FOR WARRANTY SERVICE. IMPORTANT Ne pas Réexpédier ce Produit au Magasin Pour tout problème concernant ce produit, veuillez contacter le service des consommateurs Cosmo Customer Support au +1 (888) 784-3108 UNE PREUVE D’ACHAT DATEE EST REQUISE POUR BENEFICIER DE LA GARANTIE.
MEMO
MEMO
MEMO
MEMO
APPLIANCES Cosmo is constantly making efforts to improve the quality and performance of our products, so we may make changes to our appliances without updating this manual. Electronic version of this manual is available at: www.cosmoappliances.
