Specifications
Table Of Contents
- ARM Debugger
- Brief Overview of Documents for New Users
- Warning
- Quick Start of the JTAG Debugger
- Troubleshooting
- FAQ
- Trace Extensions
- Symmetric Multiprocessing
- ARM Specific Implementations
- ARM specific SYStem Commands
- SYStem.BdmClock Define JTAG frequency
- SYStem.CLOCK Inform debugger about core clock
- SYStem.CONFIG Configure debugger according to target topology
- SYStem.CPU Select the used CPU
- SYStem.CpuAccess Run-time memory access (intrusive)
- SYStem.JtagClock Define JTAG frequency
- SYStem.LOCK Tristate the JTAG port
- SYStem.MemAccess Run-time memory access
- SYStem.Mode Establish the communication with the target
- SYStem.Option ABORTFIX Do not access 0x0-0x1f
- SYStem.Option AHBHPROT Select AHB-AP HPROT bits
- SYStem.Option AMBA Select AMBA bus mode
- SYStem.Option ASYNCBREAKFIX Asynchronous break bugfix
- SYStem.Option AXIACEEnable ACE enable flag of the AXI-AP
- SYStem.Option AXICACHEFLAGS Select AXI-AP CACHE bits
- SYStem.Option AXIHPROT Select AXI-AP HPROT bits
- SYStem.Option BUGFIX Breakpoint bug fix
- SYStem.Option BUGFIXV4 Asynch. break bug fix for ARM7TDMI-S REV4
- SYStem.Option BigEndian Define byte order (endianess)
- SYStem.Option BOOTMODE Define boot mode
- SYStem.Option CINV Invalidate the cache after memory modification
- SYStem.Option CFLUSH FLUSH the cache before step/go
- SYStem.Option CacheParam Define external cache
- SYStem.Option DACR Debugger ignores DACR access permission settings
- SYStem.Option DAPNOIRCHECK No DAP instruction register check
- SYStem.Option DAPREMAP Rearrange DAP memory map
- SYStem.Option DBGACK DBGACK active on debugger memory accesses
- SYStem.Option DBGNOPWRDWN DSCR bit 9 will be set when in debug mode
- SYStem.Option DBGUNLOCK Unlock debug register via OSLAR
- SYStem.Option DCDIRTY Bugfix for erroneously cleared dirty bits
- SYStem.Option DCFREEZE Disable data cache linefill in debug mode
- SYStem.Option DIAG Activate more data.log messages
- SYStem.Option DisMode Define disassembler mode
- SYStem.Option DynVector Dynamic trap vector interpretation
- SYStem.Option EnReset Allow the debugger to drive nRESET/nSRST
- SYStem.Option ETBFIXMarvell Read out on-chip trace data
- SYStem.Option ETMFIX Shift data of ETM scan chain by one
- SYStem.Option ETMFIXWO Bugfix for write-only ETM register
- SYStem.Option ETMFIX4 Use only every fourth ETM data package
- SYStem.Option EXEC EXEC signal can be used by bustrace
- SYStem.Option EXTBYPASS Switch off the fake TAP mechanism
- SYStem.Option FASTBREAKDETECTION Faster detection if core has halted
- SYStem.Option ICEBreakerETMFIXMarvell Lock on-chip breakpoints
- SYStem.Option ICEPICKONLY Only ICEPick registers accessible
- SYStem.Option IMASKASM Disable interrupts while single stepping
- SYStem.Option IMASKHLL Disable interrupts while HLL single stepping
- SYStem.Option INTDIS Disable all interrupts
- SYStem.Option IRQBREAKFIX Break bugfix by using IRQ
- SYStem.Option IntelSOC Debugging of an Intel SOC
- SYStem.Option KEYCODE Define key code to unsecure processor
- SYStem.Option L2Cache L2 cache used
- SYStem.Option L2CacheBase Define base address of L2 cache register
- SYStem.Option LOCKRES Go to "Test-Logic Reset" when locked
- SYStem.Option MEMORYHPROT Select memory-AP HPROT bits
- SYStem.Option MMUSPACES Enable multiple address spaces support
- SYStem.Option MonitorHoldoffTime Delay between monitor accesses
- SYStem.Option MPU Debugger ignores MPU access permission settings
- SYStem.Option MultiplesFIX No multiple loads/stores
- SYStem.Option NODATA No data connected to the trace
- SYStem.Option NOIRCHECK No JTAG instruction register check
- SYStem.Option NoPRCRReset Do not cause reset by PRCR
- SYStem.Option NoRunCheck No check of the running state
- SYStem.Option NoSecureFix Do not switch to secure mode
- SYStem.Option OVERLAY Enable overlay support
- SYStem.Option PALLADIUM Extend debugger timeout
- SYStem.Option PC Define address for dummy fetches
- SYStem.Option PROTECTION Sends an unsecure sequence to the core
- SYStem.Option PWRCHECK Check power and clock
- SYStem.Option PWRCHECKFIX Check power and clock
- SYStem.Option PWRDWN Allow power-down mode
- SYStem.Option PWRDWNRecover Mode to handle special power recovery
- SYStem.Option PWRDWNRecoverTimeOut Timeout for power recovery
- SYStem.Option PWROVR Specifies power override bit
- SYStem.Option ResBreak Halt the core after reset
- SYStem.Option ResetDetection Choose method to detect a target reset
- SYStem.Option RESTARTFIX Wait after core restart
- SYStem.Option RisingTDO Target outputs TDO on rising edge
- SYStem.Option ShowError Show data abort errors
- SYStem.Option SOFTLONG Use 32-bit access to set breakpoint
- SYStem.Option SOFTQUAD Use 64-bit access to set breakpoint
- SYStem.Option SOFTWORD Use 16-bit access to set breakpoint
- SYStem.Option SPLIT Access memory depending on CPSR
- SYStem.Option StandByTraceDelaytime Delay for activating trace after reset
- SYStem.Option STEPSOFT Use software breakpoints for ASM stepping
- SYStem.Option SYSPWRUPREQ Force system power
- SYStem.Option TIDBGEN Activate initialization for TI derivatives
- SYStem.Option TIETMFIX Bug fix for customer specific ASIC
- SYStem.Option TIDEMUXFIX Bug fix for customer specific ASIC
- SYStem.Option TraceStrobe Obsolete command
- SYStem.Option TRST Allow debugger to drive TRST
- SYStem.Option TURBO Speed up memory access
- SYStem.Option WaitReset Wait with JTAG activities after deasserting reset
- SYStem.Option ZoneSPACES Enable symbol management for ARM zones
- SYStem.RESetOut Assert nRESET/nSRST on JTAG connector
- SYStem.view Display SYStem window
- ARM Specific Benchmarking Commands
- ARM Specific TrOnchip Commands
- TrOnchip.A Programming the ICE breaker module
- TrOnchip.A.Value Define data selector
- TrOnchip.A.Size Define access size for data selector
- TrOnchip.A.CYcle Define access type
- TrOnchip.A.Address Define address selector
- TrOnchip.A.Trans Define access mode
- TrOnchip.A.Extern Define the use of EXTERN lines
- TrOnchip.AddressMask Define an address mask
- TrOnchip.ContextID Enable context ID comparison
- TrOnchip.CONVert Extend the breakpoint range
- TrOnchip.Mode Configure unit A and B
- TrOnchip.RESet Reset on-chip trigger settings
- TrOnchip.Set Set bits in the vector catch register
- TrOnchip.TEnable Define address selector for bus trace
- TrOnchip.TCYcle Define cycle type for bus trace
- TtrOnchip.VarCONVert Convert variable breakpoints
- TrOnchip.view Display on-chip trigger window
- CPU specific MMU Commands
- Target Adaption
- Support
- Products
ARM Debugger 67 ARM specific SYStem Commands
©1989-2014 Lauterbach GmbH
Example: Four cores with ETM modules.
SYStem.CONFIG ETM.Base 0x1000 0x2000 0x3000 0x4000
SYStem.CONFIG FUNNEL1.ATBSource ETM.0 0 ETM.1 1
ETM.2 2 ETM.3 3
"...2" of "ETM.2" indicates it is the third ETM module which has
the base address 0x3000. The indices of a list are 0, 1, 2, 3,...
If the numbering is accelerating, starting from 0, without gaps,
like the example above then you can shorten it to
SYStem.CONFIG FUNNEL1.ATBSource ETM
Example: Four cores, each having an ETM module and an ETB
module.
SYStem.CONFIG ETM.Base 0x1000 0x2000 0x3000 0x4000
SYStem.CONFIG ETB.Base 0x5000 0x6000 0x7000 0x8000
SYStem.CONFIG ETB.ATBSource ETM.2 2
The third "ETM.2" module is connected to the third ETB. The last
"2" in the command above is the index for the ETB. It is not a port
number which exists only for FUNNELs.
For a list of possible components including a short description
see Components and available commands.
... .BASE <address> This command informs the debugger about the start address of
the register block of the component. And this way it notifies the
existence of the component. An on-chip debug and trace
component typically provides a control register block which
needs to be accessed by the debugger to control this
component.
Example: SYStem.CONFIG ETMBASE APB:0x8011c000
Meaning: The control register block of the Embedded Trace
Macrocell (ETM) starts at address 0x8011c000 and is accessible
via APB bus.
In a SMP (Symmetric MultiProcessing) debug session you can
enter for the components BMC, COREBEBUG, CTI, ETB, ETF,
ETM, ETR a list of base addresses to specify one component per
core.
Example assuming four cores: SYStem.CONFIG
COREDEBUG.Base 0x80001000 0x80003000 0x80005000
0x80007000
For a list of possible components including a short description
see Components and available commands.
... .RESET Undo the configuration for this component. This does not cause a
physical reset for the component on the chip.
For a list of possible components including a short description
see Components and available commands.