586002-TP2-27F USER’S MANUAL 5.
Copyright © 2005, All Rights Reserved. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. Release: September 2005 Rev 1.0 Disclaimer The information contained in this document is subject to change without notice and makes no warranty of any kind with respect to this information.
Table of Contents Important Safety Instructions ............................................................................................................................................ 5 Safety Instructions for Handset Battery Pack ................................................................................................................... 6 PART I 586002TP227F FEATURES ................................................................................................................................
PART III ADVANCED SETTINGS.................................................................................................................................. 16 22 Advanced Settings Menu .................................................................................................................................... 16 Reset Handset ................................................................................................................................................ 16 Change Pin (Handset)........
Important Safety Instructions BEFORE USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY, INCLUDING THE FOLLOWING: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Read and understand all instructions. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Safety Instructions for Handset Battery Pack CAUTION: There is a danger of explosion if battery is incorrectly replaced. Use only an approved battery pack in the handset of your Cordless Telephone. To reduce the risk of fire or injury, always do the following when replacing, discarding, or charging battery. When handling the batteries, be careful not to short the battery with conducting materials such as rings, bracelets, and keys. The Battery or conducting material may overheat and cause burns.
PART I 586002TP227F FEATURES Caller ID (subscription required) Call Waiting (subscription required) Illuminated Handset Display Clock Call Timer 40 Name & Number Phonebook 6 Handset Capability 1 5 Number Redial Base to Handset Page Auto Answer out of Cradle 2-Way Intercom (requires 2 Handsets) Mute Headset Jack (2.5 mm) Tone / Pulse Dialing Handset and Base Layouts Layout of Handset Function Keys 1. Antenna 2. Earpiece 3. Display (LCD) 4. Menu / OK 5. Delete / Mute (Power) 6. Redial / Volume Up 7.
Layout of Base Functions 1. Page 2. Antenna 3. In Use/Message Waiting 4. Charge 2 Getting Started Install and Charge the Battery Pack 1. 2. 3. 4. 5. 6. 7. Open the battery cover by gently pressing down on the top of the cover while sliding it down. Plug the Battery Pack connector into the Handset socket, and then place the battery pack and wires in the compartment. The printing on the pack should be upright and facing you, with the battery wires coming from the upper right edge of the battery pack.
PART II CORDLESS PHONE OPERATION Note: If you do not press any keys for 60 seconds, your Handset will exit programming mode and return to the idle display. 3 Basic Programming Setting Date and Time Press Menu/OK, and then press ▲ or ▼ until you see >Set Clock. Press Menu/OK again. Now, use the dialpad to enter the Date, Month, and Year. If you need to correct any digits, press ◄ or ► to move the cursor backward or forward. Press ▼ to place the cursor on the next line.
Ringer Melody Press Menu/OK, and then press ▲ or ▼ until you see >Audio Settings. Press Menu/OK again. Press ▲ or ▼ until you see >Ringer Melodies. Press Menu/OK again. Press ▲ or ▼ to choose from: External Melody (outside calls) Internal Melody (intercom calls) Paging Melody Alarm Melody Press Menu/OK. Press ▲ or ▼ to select one of ten ringer melodies Press Menu/OK to confirm your selection. Press DEL/Mute 3 times to return to the idle screen.
Once you have a compatible Headset, locate the headset jack on the side of the Handset. First, remove the protective rubber cover. Plug the headset cord into the jack. Do not force the connection. When a Headset is connected, the microphone on the Handset is muted to limit the effect of background noise. Your cordless Handset is also equipped with a Belt Clip. Align the pins located on the inside edge of the clip with the notches on the sides of the Handset. The belt clip should snap securely into place.
If the displayed CID record is not in the correct format for dialing, press # repeatedly to view the other dialing format options (7,8,10 and 11 digit dialing formats). With the correct format displayed, press Talk to dial. Deleting CID Records With the desired CID record displayed, press Menu/OK. Press ▼ until you see >Delete Entry. Press Menu/OK again. You will see Delete Entry >Yes. Press Menu/OK again to confirm.
Editing Phonebook Entries In the idle mode, press ◄ to access the Phonebook. Press ▲ or ▼ to find the desired Phonebook entry. Press Menu/OK. You will see >Edit Entry. Press Menu/OK again. Use DEL/Mute to delete letters; use ◄ & ► to move the cursor back & forth. NOTE: If consecutive letters of the name are located on the same key, you will need to use ►between them. Press Menu/OK. Now, edit the phone number. Press Menu/OK to confirm. Now, follow the instructions in SPECIAL RING below.
service providers can provide this notification service. There are fees associated with this feature. Contact your service provider for details. After receiving a ‘new message’ signal from your service provider, the envelope icon will appear, alerting you that you have new message(s). In addition, the blue ring around the earpiece will flash, as well as the In Use indicator on the Base. Once you have reviewed all new voicemail messages, the indicators will turn off.
20 Key Lock To prevent accidental key presses, from the idle mode, press and hold #. Release # when the ‘key’ icon appears on the top line of the display. Your keypad is now locked. To unlock the keypad, press and hold # until the ‘key’ icon disappears. The following numbers can still be dialed when the keypad is locked: 911 000 21 Handset Power You can turn the power off on your Handset. Press and hold DEL/Mute until the screen changes, indicating shut down mode.
PART III ADVANCED SETTINGS 22 Advanced Settings Menu The Advanced Settings menu gives you access to the following options: RESET HANDSET CHANGE PIN REGISTER SELECT BASE DEREGISTER To access these options, from the idle mode: Press Menu/OK, and then press ▲ or ▼ until you see >Adv. Settings. Press Menu/OK again. Press ▲ or ▼ to choose from the list of options above. Reset Handset To restore your Handset to all factory preset settings: When you see >Reset handset, press Menu/OK.
Select Base If you have registered a Handset to more than one Base, use this feature to select the Base to which you currently want to ‘link’ that Handset (a Handset can be registered to a maximum of 4 Base Units; however, it can only work with one Base at a time): In the Advanced Settings menu, scroll ▼ to >Select Base, and then press Menu/OK. You will see a list of a Base Units to which the Handset is registered. You will also see >Automatic.
Press Menu/OK again. Now, press ▲ or ▼ to adjust ringer volume or select a ringer melody. Press Menu/OK to confirm your selection. Reset Base In the Base Settings menu, scroll ▼ to >Reset Base, and then press Menu/OK. You will see Reset to default. Scroll ▼ to >Yes, and then press Menu/OK. You will see Base is reset to default. Additional In the Base Settings menu, scroll ▼ to >Additional, and then press Menu/OK. Scroll ▼/▲ to select >Dial Mode, >Flash Time or >Prefix Dial No., and then press Menu/OK.
FCC INFORMATION Part 68 is a Federal regulation which requires equipment to be tested and registered with the FCC prior to its connection to the network. This equipment complies with Part 68 of FCC rules. On the bottom of the telephone is a label that contains, among other information, the FCC Registration Number and the Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company.
LIMITED WARRANTY If you purchased this product new in the U.S. or Puerto Rico, CORTELCO warrants it against defects in material and workmanship for a period of one (1) year from the date of original purchase. This warranty is in lieu of all other express warranties. During the warranty period, CORTELCO agrees to repair or, at its option, replace the defective product, or any part of it without charge for parts or labor. This is your exclusive remedy.
