Manual

ManualsBrandsCortech ManualsEquipmentRSL-2701

TABLE TOP LAMINATOR

RSL-2701 OWNER’S MANUAL

Please read instructions carefully before use.

TABLE OF CONTENTS

▣Introduction ----------------------------------------------------------------------------------- 3

▣Package Contents --------------------------------------------------------------------------- 3

▣Safety Precautions --------------------------------------------------------------------------- 4

▣Parts -------------------------------------------------------------------------------------------- 5

▣Features Guide ------------------------------------------------------------------------------- 6

▣Operating Instructions -------------------------------------------------------------------- 8

▣Film Loading and Threading ------------------------------------------------------------ 8

▣Maintenance --------------------------------------------------------------------------------- 11

▣Trouble shooting guide ------------------------------------------------------------------- 12

▣Specifications ------------------------------------------------------------------------------- 13

▣Warranty ----------------------------------------------------------------------------------- 14

Summary of content (7 pages)

PAGE 1
TABLE OF CONTENTS ▣Introduction ----------------------------------------------------------------------------------- 3 ▣Package Contents TABLE TOP LAMINATOR RSL-2701 OWNER’S MANUAL --------------------------------------------------------------------------- 3 ▣Safety Precautions --------------------------------------------------------------------------- 4 ▣Parts -------------------------------------------------------------------------------------------- 5 ▣Features Guide -------------------------------
PAGE 2
SAFETY PRECAUTIONS INTRODUCTION Thank you for purchasing RSL-2701 Table Top Laminator. It has been designed and manufactured to provide years of continuous service. For high quality lamination, please read this instruction manual thoroughly. This manual will provide you with complete operating and maintenance information. PACKAGE CONTENTS WARNING Failure to comply with any of the following safety procedures could result in serious injury. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
PAGE 3
PARTS FEATURES GUIDE Run and stop the machine ③ ⑧ ① Reverse the rollers to undo jams and correct misfed documents ④ ⑨ Reduce roller speed (1~10 speed settings) ⑥ ⑤ Increase roller speed (1~10 speed settings) ② ⑦ 123456789- Upper Film Lower Film Idle Bar Hot Rollers Feed Table Paper Guide Control Panel Tension Knob Power Switch 210° F~230° F 230° F~270° F 270° F~310° F Film Application Temperature 210° F~230° F Film Application Temperature 230° F~270° F Film Application Temperature 270° F~310°
PAGE 4
FPower Switch (1) - Located on the rear of OPERATING INSTRUCTION the machine. “I” (on) “0” (off). (Fig. 2) Cross Cutter (2) - Used to cut off the 1. 2. 3. 4. 5. ② ① laminated web. (Fig. 2) Figure 2 ④ Feed Guide (3) –The feed guide permits alignment of the item(s) to be laminated. To position the adjustable guide, loosen the knob, slide it to the desired position and tighten the knob to secure the feed guide in place. (Fig.
PAGE 5
▲ 4. Insert the film shaft into the roll of film from the right side with the copper end last. Align and insert the core adapter on the left end of the film core. LOADING UPPER ROLL FILM 1. Slightly slide the shaft to the right and pull it out from the machine. Figure 10 5. Center the film on the shaft and lock it in place with the locking core adapters Figure 7 2. Take both lock core adapters off from the shaft. Figure 11 6. Carefully return the film shaft back into place. Figure 8 3.
PAGE 6
▲ 1. 2. LOADING LOWER ROLL FILM Repeat steps 1-5 to load lower roll film. Once the upper and lower film is on the shaft, pull the film from the top roll down to the bottom roll to make certain that the film is aligned properly. Then tighten the lower locking core screws. NOTE: If the film is not aligned properly exposed adhesive will adhere to the rollers and may cause the film to jam. ▲ TROUBLE SHOOTING GUIDE Problem Cause Remedy Rollers do not operate after the RUN/STOP Button is pressed 1.
PAGE 7
SPECIFICATIONS WARRANTY MODEL RSL-2701 Power supply AC 120V / 60Hz Power consumption 1450W Max laminating width 685(mm) / 27(in) Film thickness 25~125(mic) / 1~5(mil) Max laminating speed 2.4(m/min) / 7.