Owners manual

03/23/16
INS5316
CORSA Performance · 140 Blaze Industrial Pkwy · Berea, OH 44017 · P: [phone] · F: [phone]
9
E - M a i l : s a l e s @ c o r s a p e r f o r m a n c e . c o m · w w w . c o r s a p e r f o r m a n c e . c o m
Exhaust System Installation
Cat Back Exhaust System
Dual Rear Exit
2015 Dodge Charger & Challenger 6.4L V8
PN 14993, 14994, 14995(BLK), 14996(BLK)
8. Locate a 2.75” clamp and the driver side valve assembly. Verify the scribed “D” is present on the valve
assembly. Install the clamp on the expanded outlet end of the driver side x-pipe outlet. Position the clamp so
that the bolt is vertical with the nut towards the ground and the bolt towards the inside of the vehicle. Next,
insert the driver side valve assembly hanger into the corresponding driver side tunnel hanger grommet.
(Fig. AA) Then, slide the valve assembly into the expanded end of the x-pipe outlet. (Fig. BB) Rotate the valve
assembly so that the hanger is parallel with the ground and the hanger grommet is swung forward. Using a
15mm deep socket and ratchet, snug the clamp.
NOTE: The active valve module should be facing the outside or driver side of the vehicle.
9. Locate a 2.75” clamp and passenger side valve assembly. Verify the scribed “P” is present on the assembly.
Install the clamp on the expanded outlet end of the passenger side x-pipe outlet. Position the clamp so that the
bolt is vertical with the nut towards the ground and the bolt towards the inside of the vehicle. Next, insert the
passenger side valve assembly hanger into the corresponding passenger side tunnel hanger grommet. Then,
slide the valve assembly into the expanded end of the x-pipe outlet. (Fig. CC) Rotate the valve assembly so that
the hanger is parallel with the ground and the hanger grommet is swung forward. Using a 15mm deep socket
and ratchet, snug the clamp.
NOTE: The active valve module should be facing the center or driver side of the vehicle.
10. Locate the passenger side axle pipe along with a 2.75” clamp. Install the clamp on the expanded end of the axle
pipe. Position the clamp so that the bolt is vertical with the nut towards the ground and the bolt towards the
outside of the vehicle. Slide the expanded end of the axle pipe over the passenger side valve assembly.
(Fig. DD) Using a 15mm deep socket and ratchet, snug the clamp.
11. Repeat step #10 for the driver side of the vehicle.
12. Locate the passenger side rear muffler, a 2.75” clamp, the corresponding passenger hanger grommet assemblies
removed from the stock exhaust removal process, and the two 13mm bolts for the hanger grommet assemblies.
If present, install the front hanger grommet onto the front muffler hanger in the same position as removed from
the stock exhaust. (Fig. EE) Next, install the rear hanger grommet onto the rear muffler hanger, again, in the
same position as removed from the stock exhaust. (Fig. FF) Then, install the clamp on the expanded end of the
rear muffler inlet pipe. Position the clamp so that the bolt is vertical with the nut towards the ground and the
bolt towards the front of the vehicle. Slide the expanded end of the muffler inlet pipe over the passenger side
axle pipe. Using a 13mm short socket, swivel adapter, 3/8” drive extension, and ratchet install the front and
rear hanger grommet assemblies reusing the stock bolts. (Fig. GG & HH). On the passenger side only, clip the
ground wire from the hanger grommet assembly onto the rear muffler hanger. (Fig. II) Using a 15mm deep
socket and ratchet, snug the clamp. (Fig. JJ)
INSTALLATION INSTRUCTIONS CONTINUED ON NEXT PAGE