IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Exhaust We ask that you take a few moments to compete our warranty registration form: TO ACTIVATE YOUR LIMITED LIFETIME WARRANTY GO TO: CORSAPERFORMANCE.COM/WARRANTY STOP For Full-Color Installation Instructions, Please Visit: CORSAPERFORMANCE.
Exhaust System Installation Valve Back Exhaust System 2014-Current C7 Corvette PN’s 14762, 14763, 14764, 14765 Polished & Black Quad 4.5” Pro or Poly Tips Please take time to read and understand these installation instructions. CORSA recommends that the installation of this system be performed by a qualified service center or professional muffler installer who has the necessary equipment, tools and experienced personnel.
Exhaust System Installation Valve Back Exhaust System 2014-Current C7 Corvette PN’s 14762, 14763, 14764, 14765 Polished & Black Quad 4.5” Pro or Poly Tips Tip Section Bill of Materials 1. Tip Assembly: 14062/14062BLK (Quad 4.5” Pro Series Tip Asm. – Used on 14762/14764) 14063/14063BLK (Polygon Tip Asm. Used on 14763/14765) 2.
Exhaust System Installation Valve Back Exhaust System 2014-Current C7 Corvette PN’s 14762, 14763, 14764, 14765 Polished & Black Quad 4.5” Pro or Poly Tips 6. CAREFULLY Remove the two reflectors on each side to enable access to the four outer mounting bolts for the rear fascia. Each reflector is snapped in place using three tabs, which can be pushed out from inside the fascia. (Fig I) 7.
Exhaust System Installation Valve Back Exhaust System 2014-Current C7 Corvette PN’s 14762, 14763, 14764, 14765 Polished & Black Quad 4.5” Pro or Poly Tips 17. Remove both of the factory valve control units to protect them during the cutting process. Remove the three screws securing each of the control units using an 8mm socket and 1/4” ratchet. (Fig. Y) 18. Using a saw or chain-style pipe cutter, cut each pipe at the mark. The cut should be as close to parallel to the edge of the valve as possible.
Exhaust System Installation Valve Back Exhaust System 2014-Current C7 Corvette PN’s 14762, 14763, 14764, 14765 Polished & Black Quad 4.5” Pro or Poly Tips Factory Exhaust Removal Pictures Fig. J Fig. K Fig. L Fig. M Fig. N Fig. O Fig. P Fig. Q Fig. R Fig. S Fig. T Fig. U REMOVAL PICTURES CONTINUED ON NEXT PAGE INS5284 05/05/2014 CORSA Performance · 140 Blaze Industrial Pkwy · Berea, OH 44017 · P: (440) 891.0999 · F: (440) 891-1868 E - Ma il : s al es @c o rs a p er f orm a nc e .
Exhaust System Installation Valve Back Exhaust System 2014-Current C7 Corvette PN’s 14762, 14763, 14764, 14765 Polished & Black Quad 4.5” Pro or Poly Tips Factory Exhaust Removal Pictures INS5284 05/05/2014 Fig. V Fig. W Fig. Y Fig. Z Fig. X Fig. AA CORSA Performance · 140 Blaze Industrial Pkwy · Berea, OH 44017 · P: (440) 891.0999 · F: (440) 891-1868 E - Ma il : s al es @c o rs a p er f orm a nc e .c om · www. c o rs a p e rf o rm a n ce .
Exhaust System Installation Valve Back Exhaust System 2014-Current C7 Corvette PN’s 14762, 14763, 14764, 14765 Polished & Black Quad 4.5” Pro or Poly Tips Installation of CORSA Exhaust System: NOTE: Apply the anti-seize lubricant (supplied) to the threads ONLY of all the clamps. Failure to follow this procedure can cause nuts to seize on clamps and potentially destroy threads. After applying anti-seize lubricant, be sure to thoroughly clean your hands, as lubricant will tarnish stainless steel.
Exhaust System Installation Valve Back Exhaust System 2014-Current C7 Corvette PN’s 14762, 14763, 14764, 14765 Polished & Black Quad 4.5” Pro or Poly Tips 5. Reinstall the factory valve control units using an 8mm socket and ¼” ratchet. Both axle pipes should now appear as shown, with the valve control units reinstalled, and each of the clamp on elbows installed properly. (Fig. F) 6. Install each axle pipe back into the chassis as shown, making sure to reconnect the AFM valve wire.
Exhaust System Installation Valve Back Exhaust System 2014-Current C7 Corvette PN’s 14762, 14763, 14764, 14765 Polished & Black Quad 4.5” Pro or Poly Tips 13. Rotate the rear mufflers upwards until the hole sets align in the muffler tie brackets. Load the two M8 flange bolts and lock washers in from the front. Place the half round spacer onto the bolts from the backside, so it sits inside the “V” shape of the passenger side tie bracket.
Exhaust System Installation Valve Back Exhaust System 2014-Current C7 Corvette PN’s 14762, 14763, 14764, 14765 Polished & Black Quad 4.5” Pro or Poly Tips IMPORTANT NOTE DO NOT over-tighten the clamps on the tip assembly, as this will make future removal of the tip assembly much more difficult. The C7 CORSA tip assemblies are designed to be interchangeable, between the different tip designs and finishes. 25.
Exhaust System Installation Valve Back Exhaust System 2014-Current C7 Corvette PN’s 14762, 14763, 14764, 14765 Polished & Black Quad 4.5” Pro or Poly Tips CORSA Exhaust Installation Pictures: Fig. E Fig. F Fig. G Fig. H Fig. I Fig. J Fig. K Fig. L Fig. M Fig. N Fig. O Fig. P INSTALL PICTURES CONTINUED ON NEXT PAGE INS5284 05/05/2014 CORSA Performance · 140 Blaze Industrial Pkwy · Berea, OH 44017 · P: (440) 891.0999 · F: (440) 891-1868 E - Ma il : s al es @c o rs a p er f orm a nc e .
Exhaust System Installation Valve Back Exhaust System 2014-Current C7 Corvette PN’s 14762, 14763, 14764, 14765 Polished & Black Quad 4.5” Pro or Poly Tips CORSA Exhaust Installation Pictures: Fig. Q Fig. R Fig. S Fig. T Fig. U Fig. V Fig. W Fig. X Fig. Y Fig. Z Fig. AA Fig. BB INSTALL PICTURES CONTINUED ON NEXT PAGE INS5284 05/05/2014 CORSA Performance · 140 Blaze Industrial Pkwy · Berea, OH 44017 · P: (440) 891.0999 · F: (440) 891-1868 E - Ma il : s al es @c o rs a p er f orm a nc e .
Exhaust System Installation Valve Back Exhaust System 2014-Current C7 Corvette PN’s 14762, 14763, 14764, 14765 Polished & Black Quad 4.5” Pro or Poly Tips CORSA Exhaust Installation Pictures: Fig. CC Fig. DD Fig. EE Fig. FF Fig. GG Fig. HH Fig. II Fig. JJ Fig. LL INS5284 05/05/2014 Fig. KK Fig. MM Fig. NN CORSA Performance · 140 Blaze Industrial Pkwy · Berea, OH 44017 · P: (440) 891.0999 · F: (440) 891-1868 E - Ma il : s al es @c o rs a p er f orm a nc e .c om · www.
