Coronis Getting Started Guide Supported displays: MDCC 2121, MDCC 3120, MDCG 2121, MDCG 3120
(This page intentionally left blank.
Copyright notice This document is copyrighted. All rights are reserved. Neither this document, nor any part of it, may be reproduced or copied in any form or by any means - graphical, electronic, or mechanical including photocopying, taping or information storage and retrieval systems without written permission of Barco © 2010 Barco N.V. All rights reserved. Notice Although every attempt has been made to achieve technical accuracy in this document, we assume no responsibility for errors that may be found.
(This page intentionally left blank.
Table of Contents Table of Contents Preface..................................................................................... 7 FCC compliance information ............................................................ 8 FCC Compliance Information (display)..................................... 8 FCC Compliance Information (display controller) .................... 9 CE mark notice ............................................................................... 10 Environmental information ...................
Table of Contents Cable routing .................................................................................. 49 Cleaning instructions...................................................................... 52 Precautions.............................................................................. 52 Front glass ............................................................................... 52 Cabinet ....................................................................................
Preface Preface 7
FCC compliance information FCC compliance information FCC Compliance Information (display) Class A: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC compliance information FCC Compliance Information (display controller) CLASS B: This Barco Graphics Controller complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation.
CE mark notice CE mark notice Declaration of Conformity in accordance with Article 10 (1) of the CE directive This product has been designed and manufactured in accordance with the essential requirements of the Directives 89/336/EEC and MDD 93/42/EEC (class II b product), and for this product the procedures of Annex II have been applied to mark the product with the CE label.
Environmental information Environmental information Disposal Information This product consists of devices that may contain mercury, which must be recycled or disposed of in accordance with local, state, or country laws. (Within this system, the backlight lamps in the monitor display contain mercury.) This equipment has required the extraction and use of natural resources for its production. It may contain hazardous substances for health and environment.
Environmental information Information for China ROHS compliance Table of toxic and hazardous substances/elements and their content, as required by China’s management methods for controlling pollution by electronic information products Toxic or hazardous Substances and Elements Part Name Pb Hg Cd Cr6+ PBB PBDE Metal parts O O O O O O Plastic parts O O O O O O PCB or PCBA O O O O O O LCD panel X X O O O O Power supply/adapter X O O O O O Power cable X O O O O O
Environmental information LCD Monitor 零部件名稱 金属机构件 塑料机构件 电路板组件 * 液晶面板 电源模块 / 适配器 电源线 外部信号连接线 有毒有害物質或元素 汞 镉 铅 （Pb） （Hg） （Cd） O O O O O O O O O X X O X O O X O O O O O 六价铬 （Cr6+） O O O O O O O 多溴联苯 多溴二苯醚 （PBB） （PBDE） O O O O O O O O O O O O O O *：电路板组件包括印刷电路板及其构成的零部件，如电阻、电容、集成电路 、连接器等 ○：表示该有毒有害物质在该部件所有均质材料中的含量均在 《电子信息产品中有 毒有害物质的限量要求标准》规定的限量要求以下 ×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 《电子信息产品中 有毒有害物质的限量要求标准》规定的限量要求； 但是上表中打 “×” 的部件，其含量超出是因为目前业界还没有成熟的可替代的技术 13
Safety Instructions Safety Instructions General Recommendations Read the safety and operating instructions before operating the display. Retain safety and operating instructions for future reference. Adhere to all warnings on the display and in the operating instructions manual. Follow all instructions for operation and use.
Safety Instructions • The medical approved DC power supply must be powered by the AC mains voltage. Power cords: • Utilize a UL-listed detachable power cord, 3-wire, type SJ or equivalent, 18 AWG min., rated 300 V min., provided with a hospital-grade type plug 5-15P configuration for 120V application, or 6-15P for 240V application. • Do not overload wall outlets and extension cords as this may result in fire or electric shock. • Mains lead protection (U.S.
Safety Instructions This apparatus conforms to: CE0120 (MDD 93/42/EEC class IIb product), IEC 60601-1, UL 60601-1, CAN/CSA C22.2 No. 601.01-M90 (c-UL), CCC GB4943-1995 (IEC 60950-1). National Scandinavian Deviations for Cl. 1.7.
Explanation of symbols Explanation of symbols Symbols on the display and / or power supply On the display or power supply, you may find the following symbols (nonrestrictive list): Indicates compliance to the essential requirements of the Directive 93/42/EEC Indicates compliance with Part 15 of the FCC rules (Class A or Class B) Indicates the display is approved according to the UL regulations or or Indicates the display is approved according to the c-UL regulations Indicates the display is approved acc
Explanation of symbols Indicates the display serial no.
Recommendations for using your display system Recommendations for using your display system 1. Optimize the lifetime of your display Enabling the Display Power Management System (DPMS) of your display (in the display’s Settings menu) will optimize its diagnostic lifetime by automatically switching off the backlight when the display is not used for a specified period of time. By default, DPMS is enabled on your display, but it also needs to be activated on your workstation.
Recommendations for using your display system diagnostic performance of the product. To ensure optimal product quality, Barco applies strict selection criteria for its LCD panels. To learn more about LCD technology and missing pixels, consult the dedicated white paper available at www.barcomedical.com. 4. Enhance user comfort Every Barco multi-head display system is color matched with the highest specification in the market. Barco recommends keeping color-matched displays together.
Display controller installation Display controller installation 21
Display Controller Installation Display Controller Installation Which display controller? Your Barco medical display is compatible with a large range of Barco and non-Barco display controller boards. Depending on the customer’s order details, the display can be delivered with or without display controller. The brochure “Barco medical display overview” on the website www.barco.
Display Controller Installation Types of display controllers for Barco Display Systems The following models of Barco display controllers are available for your display system.
Display Controller Installation Figure 1: Display controller VGA Jumper, VGA enabled Note: To use multiple BarcoMed display controllers in a single computer, you need to enable VGA on only ONE of the BarcoMed display controllers and disable VGA on ALL the other BarcoMed display controllers. To use a BarcoMed display controller with a third party VGA controller or with one or more Barco MXRT display controllers, do NOT enable VGA on the BarcoMed display controller.
Display Controller Installation Installation Procedure The following instructions will take you step by step through the installation of the display controller(s) for your BARCO CORONIS Display System. CAUTION – Wear a grounded, protective ESD strap when handling or during installation of the display controller. Electrostatic charges can damage the display controller. 1. If you are not going to use your old graphics card, uninstall the drivers and software for it if you have not already done so. 2.
Display Controller Installation 7. Align the display controller(s) for your BARCO CORONIS Display System with the slot(s) and press it(them) in firmly until the card(s) is(are) fully seated. Note: The next step applies only to the MXRT 5100, MXRT 7100, and MXRT 7200. 8. Connect the power cable(s) to the 6-pin power connection(s) on the graphics card. Make sure the cables are not interfering with anything inside the computer (for example, a cooling fan).
Display Controller Installation 9. Screw in or fasten the display controller securely. Replace and secure the computer cover. 10. Connect your BARCO CORONIS Displays to the display controller(s) for your BARCO CORONIS Display System using the cables supplied. Make sure all cables are securely connected before turning on your system.
Display Controller Installation Figure 7: IO-Panel for the Barco MXRT 2100 and Barco MXRT 5200 MXRT 2100 MXRT 5200 X Head 2– DVI-I Connection X Head 1– DVI-I Connection Y Head 1– DVI-I Connection Y Head 2– DVI-I Connection Note: For 6mp, connect Head 1 to left input, and Head 2 to right input. Figure 8: IO-Panel for the Barco MXRT 5100, Barco MXRT 7100 and Barco MXRT 7200 28 X Head 1 – DVI-I Connection Y Stereo Connection This option is not supported by Barco.
Display Controller Installation Note: For 6mp, connect Head 1 to left input, and Head 2 to right input. Figure 9: IO-Panel for the Barco MXRT 7300 X DisplayPort Connections Y DVI-I Connection Note: Disconnecting the DisplayPort cable may lock the display. Note: Only two of the three connectors can be used at a time. Driving three displays is not supported with the MXRT 7300.
Display Controller Installation 12. Turn on the display(s) and then your computer. Turning on your system WARNING - Turn on your display(s) before you turn on your computer. Failure to do so could damage your display(s). If you have properly installed your graphics card, the Windows start-up messages will appear once the boot procedure is finished. Note: Your Barco display(s) will be running in a basic video mode at a default refresh rate.
Display installation Display installation 31
Installation precautions Installation precautions Precautions • Keep your original packaging. It is designed for this display and is the ideal protection during transport. • Avoid reflections in the flat panel to reduce eye strain. • Place the display on a strong and stable table or desk. • Keep the display away from heat sources and provide enough ventilation around the display. • Do not use the display in direct sunlight. • Do not scratch or apply pressure to the screen. This may cause permanent damage.
Display parts, controls and connectors Display parts, controls and connectors Front The front controls are soft touch keys. When you touch any of them while no on-screen display (OSD) is on the screen, the front illumination is switched on for a few seconds. When you touch a key again while the illumination is on, the function of the key is executed. 7 6 1 2 3 4 5 Figure 11: Front view 1. Left/Down To move down or decrease values in the OSD. 2. Right/Up To move up or increase values in the OSD. 3.
Display parts, controls and connectors To display the OSD (on-screen display). In the OSD, this button acts as Enter button to make selections. 4. Standby To put the display in standby mode. 5. Ambient light sensor Senses the ambient light around the display. The ambient light measurement is taken into account in the DICOM display function calibration. 6. Power LED Indicates the display’s power status. Green: Display is on (when enabled in the OSD). Orange: Display is in Standby power-saving mode.
Display parts, controls and connectors Rear 1 2 3 4 Figure 12: Rear view 1. Connector compartment cover. Detach to get access to the signal connectors. 2. Slot for security cable (e.g., Kensington lock). 3. Push-button to release the panel unit from the tilt & swivel foot in landscape orientation. 4. (Not visible on drawing, hidden by the display stand) Pushbutton to release the panel unit from the tilt & swivel foot in portrait orientation. Connectors 6 1 2 3 4 5 Figure 13: Connectors 1.
Display parts, controls and connectors Connect the output of the DC power supply delivered with the display to this connector. 2. +5 Vdc, 0.25 A power output for accessories. 3. DVI (digital) video input. 4. USB upstream port (to PC). 5. USB downstream port (to peripheral USB devices). 6. Power output for asset management. Side 1 2 Figure 14: Side view 1. Display panel unit 2. USB downstream ports.
Display parts, controls and connectors Foot The display stand is packaged separately from the display panels. After unpacking you have to click the panels to the stand. There are several types of stands, depending on the number of panels in the system. Single-head stand 1 2 Figure 15: Single-head stand (rear view) 1. Tilt & swivel neck cover. Detach before connecting the signal cables. 2. Cable duct covers. Push down and turn to open before connecting the signal cables.
Display parts, controls and connectors Dual-head stand 3 4 Figure 16: Dual-head stand (rear view) 3. Arm covers. The covers are packaged separately from the stand. You have to click them to the arms after connecting the signal cables. 4. Cable duct covers. Push down and turn to open before connecting the signal cables.
Single-head installation Single-head installation To attach the panel unit to the display stand: 1. Take the display stand from the packaging and put it on a solid flat surface. 2. Take the panel unit from the packaging and hold it in portrait position. The I-Guard should be positioned bottom right. 3. Hook the top gaps in the rear of the panel over the top anchors of the stand attachment plate (1). see figure 17. 4.
Single-head installation To detach the panel unit from the display stand: 1. Firmly push the push-button at the rear of the panel (3) or (4). Push button (3) to release the panel in landscape position. Push button (4) to release the panel in portrait position (button not visible on drawing because hidden by the display stand). 2. Pull the bottom of the panel towards you and at the same time lift the panel from the stand attachment plate.
Dual-head installation Dual-head installation To attach the panel units to the dual-head stand: 1. Take the stand from the packaging and put it on a solid flat surface. Figure 18: Dual-head stand 2. Unpack the panels. 3. Slide the display brackets on the stand arms in the correct position. The correct position is indicated on a label on the rear of the panels. There is a measure for portrait orientation and one for landscape orientation.
Dual-head installation Display bracket position (multi-head): Portrait orientation: 46mm Landscape orientation: 100mm Figure 19: Example of label with position for brackets 130 120 110 100 90 80 70 60 50 40 30 20 10 0 Figure 20: Shift brackets according to label indication 4. Take one of the panels and hold it in the desired position (portrait or landscape).
Dual-head installation 5. Hook the top gaps in the rear of the panel over the top anchors of the bracket (figure 21 below). 6. Push the bottom of the panel firmly towards the stand so that the bottom anchors clip in the bottom gaps (figure 21 below). 1 2 Figure 21: 7. Repeat steps 4. to 6. for the second panel in the packaging. 8. Check that both panels are firmly attached.
Vesa-mount installation Vesa-mount installation Important: • Use an arm that is approved by VESA (according to the VESA 100 mm standard). • Use an arm that can support a weight of at least 10 kg (22.05 lbs). To attach the panel unit to an arm stand: 1. Unscrew the 4 screws (M4 x 8 mm) from the rear of the display panel. 2. Attach the panel firmly to the arm stand using 4 screws M4 x 10 mm.
Adjust panel orientation Adjust panel orientation To adjust the panel orientation: 1. Before turning the display panel, lift it in its heighest position. If not, the corner of the panel might hit the foot during the rotation. 2. To change from portrait to landscape, turn the panel counterclockwise. 3. To change from landscape to portrait, turn clockwise.
Connecting the signal cables Connecting the signal cables To connect the signal cables to the display: 1. Make sure the computer is turned off. 2. To get access to the connectors, remove the connector compartment cover (1). To remove the cover, gently pull the bottom side of the cover upward or firmly press down the 2 clips at the top side (positions marked in the plastic). 3. To facilitate cable routing afterwards, remove the tilt & swivel neck cover (2).
Connecting the signal cables 5. Connect signal cables: 7 4 5 6 Figure 26: Signal cable connections • Connect one end of the DVI cable to the DVI input of the display (4). Connect the other end of the DVI cable to the DVI connector of the display controller board. • Connect a PC USB downstream connector to the display’s USB upstream connector by means of a USB cable (5).
Connecting the signal cables 7 8 Figure 27: External DC power supply 48
Cable routing Cable routing To route the cables: Figure 28: Display rear view 1. Bind the cables in the connector compartment together with the cable tie inside the connector compartment. 2. Route the cables alongside the neck and in the cable ducts in the tilt & swivel foot. See figure 28 above. 3. Re-attach the connector compartment cover and neck cover. Close the cable duct covers. Push the cable duct covers upward to lock them. To route the cables: 1.
Cable routing 3. Unpack the plastic stand arm covers and attach them to the display stand. To attach the arm covers, first slide the covers horizontally over the arms and then push them firmly against the arms so that the covers’ plastic clips hook in the grooves in the metal arms.
Cable routing 4. Close the cable duct covers. Push the cable duct covers upward to lock them.
Cleaning instructions Cleaning instructions Precautions • Take care not to damage or scratch the glass or LCD panel. Be careful with rings or other jewellery that can touch the glass. • Do not apply pressure on the glass or LCD panel. • Do not apply or spray liquid directly to the glass, panel or cabinet as excess liquid may cause damage to internal electronics. Instead, apply the liquid to the cleaning cloth.
Cleaning instructions • Detergents with ammonia • Detergents with abrasives • Steel wool • Sponge with abrasives • Steel blades • Cloth with steel thread Cabinet Proceed as follows: • Clean the cabinet using a soft cotton cloth, lightly moistened with a recognized cleaning product for medical equipment. • Repeat with water only. • Wipe dry with a dry cloth.
Cleaning instructions (This page intentionally left blank.
Software installation Software installation 55
Driver and Software Installation Driver and Software Installation This chapter will guide you through the installation of the drivers, software and documentation associated with your BARCO CORONIS Display System or BARCO CORONIS Display(s). The process for the BARCO MXRT family of controllers and BARCOMED family of controllers is handled separately. If you install Barco displays without Barco display controllers, no drivers will be installed. Only the online user manual will be installed on your system.
Driver and Software Installation • Windows XP Professional x64 Edition, • Windows Server 2003, • Windows Server 2003 x64 Edition, • Windows Server 2008, • Windows 2008 x64, and • Windows Vista 32 & 64 Bit Edition. You will need to install the BARCO CORONIS Display system drivers and software in the following cases: • After you have installed the display controller(s) for your BARCO CORONIS Display System in your system for the first time. • After you have reinstalled or upgraded your operating system.
Driver and Software Installation b) Click Run. c) Click Browse and browse to the root directory of the BARCO CORONIS Display System Installation CD-ROM and click on the file, Setup.exe, and click Open. d) Click OK. or a) Browse to the root directory of the BARCO CORONIS Display System Installation CD-ROM and double click on the file, Setup.exe. 3. Click Next twice. 4. Click Yes to accept the terms of the MediCal QAWeb Agent license agreement.
Driver and Software Installation 10. When the Setup complete message appears, select Reboot System Now and click Finish. 11. After the system reboots, Windows may display either the Digital Signature Not Found message or The software you are installing for this hardware has not passed Windows logo testing.
Driver and Software Installation Figure 31: Barco MXRT Driver Removal Wizard (driver version may be different than what is pictured) Note: Vista Only: After uninstalling the driver, shutdown the machine and remove the card. If you leave the card in the system, Vista will automatically reinstall the driver. If you are uninstalling the Barco MXRT drivers prior to doing a driver upgrade, complete the Barco MXRT Driver Removal Wizard as described, and reboot the system into Safe Mode.
Driver and Software Installation To install the drivers and software silently, please follow the steps below: 1. Insert the BARCO CORONIS Display System Installation CD-ROM into your CD/DVD drive. When the Barco Product Installation Wizard starts click “Cancel”. 2. Click the Start button in the task bar. 3. Click Run. 4. Click Browse and a) Browse to the root directory of the BARCO CORONIS Display System Installation CD-ROM. b) Click on the file, Setup.exe, and click Open.
Driver and Software Installation Figure 32: Command line installation Note: When performing an MXRT driver upgrade, it is essential to uninstall the previous installation before installing the new driver. We also recommend that you perfrom the following steps to completely remove the previously installed files: a) Boot the system in safe mode. b) Run MXRT driver cleaner.
Driver and Software Installation • Windows Server 2003 x64 Edition, and • Windows Vista 32 & 64 Bit Edition. You will need to install the BARCO CORONIS Display system drivers and software in the following cases: • After you have installed the display controller(s) for your BARCO CORONIS Display System in your system for the first time. • After you have reinstalled or upgraded your operating system. • After you have moved the display controller(s) to a different PCI/PCIe slot. 1. Start your system.
Driver and Software Installation 4. Follow the wizard’s on-screen instructions to complete the installation. Note: When the page shown in figure 33 appears you may either click Next to accept the default settings or if you know the settings required for your viewing application, you may select them now and then click Next. You may change these settings later by accessing the Barco Driver tab within the Windows Display Control Panel.
Driver and Software Installation installing for this hardware has not passed Windows logo testing. Automated display configuration Once the drivers, software and documentation have been installed and your system has been rebooted, the Barco Monitor Plug and Play Software should automatically detect your Barco displays and attach them to the desktop with the correct resolution.
Driver and Software Installation Figure 34: Barco Driver Removal Wizard Command line (Silent) Install of Drivers and Software (Not supported with Windows Vista) Specifying the silent install option causes most of the GUI associated with the installer to disappear. A background progress window will still be visible, but no user input will be required. The silent install behavior is dictated by the SETUP.INI file.
Driver and Software Installation a) Browse to the root directory of the BARCO CORONIS Display System Installation CD-ROM. b) Click on the file, Setup.exe, and click Open. or a) Browse to the root directory of the location where you saved the contents of your BARCO CORONIS Display System Installation CD-ROM. b) Click on the file, Setup.exe, and click Open. 5. In the Open address window, place your cursor at the end of the line of text that appears and add the following text after Setup.
Driver and Software Installation (This page intentionally left blank.
Where to get more information Where to get more information Where to find more information The following documentation is included with your system: Document Location Information Quick install sheet System box Brief overview of the complete system set-up Online user guide Installed on the PC Detailed description of the graphic board control panels and display controls and functions Getting started guide (PDF) System CD-ROM This booklet in PDF format Online user guide (PDF) System CD-ROM Same
Where to get more information • In the Security section, check the option Allow active content to run in files on My Computer 70
Troubleshooting Troubleshooting 71
General tips General tips • If one display from a multi-head system exhibits problems, try to eliminate the problem by switching video cables or power supplies. In that way you can find out if the problem resides in the display or not.
Configuring Windows Configuring Windows Setting the resolution of your BARCO CORONIS Display Note: In order to set the resolution of your BARCO CORONIS Display you must be logged in using an account with administrator privileges. Accessing the Windows Display Control Panel 1.
Configuring Windows rectangle for the virtual display representing the two heads controlled by each BarcoMed display controller output. If you installed your BARCO CORONIS Display System drivers in DualView mode (default for Windows XP) there will be a rectangle representing each head controlled by each output of the display controller. This will be true even if you have only one display connected to your BarcoMed controller.
Configuring Windows To set the resolution of the second display attached to the BarcoMed display controller you are working with, go back to the “Settings” tab of the “Display Properties Control Panel”. If necessary attach the second display you detached in step 2 above, by right clicking on the rectangle that represents it and selecting Attached. Now repeat steps 5-8 above for this display.
Configuring Windows (This page intentionally left blank.
Technical Specifications Technical Specifications 77
Technical Specifications : Item 78 MDCC 2121 MDCG 2121 Picture panel TFT AM-LCD Dual Domain IPS color (From Oct. 2008: IPSPro) IPS SA-TFT Native resolution 1600x1200 1600x1200 Native color resolution 8 bits / sub-pixel 8 bits / sub-pixel Pixel Pitch 0.270 mm (H) x 0.270 mm (V) 0.270 mm (H) x 0.270 mm (V) Active diagonal 540 mm (21.3 -inch) 540 mm (21.3 -inch) Display area (H x V) 432.0x324.0 (mm) 432.0x324.
Technical Specifications Item MDCC 2121 MDCG 2121 Signal systems DVI Digital Complying to DVI Rev 1.0 specifications DVI single and dual link Complying to DVI Rev 1.0 specifications USB standard USB 2.0 USB 2.
Technical Specifications Item 80 MDCC 2121 MDCG 2121 Humidity 8% - 80% (non-condensing) for operation 5% - 95% (non-condensing) for storage 8% - 80% (non-condensing) for operation 5% - 95% (non-condensing) for storage Altitude 7500 m storage 3000 m operation 7500 m storage 3000 m operation
Technical Specifications Item MDCC 3120 MDCG 3120 Picture panel TFT AM-LCD Dual Domain IPS color AM-LCD IPS Native resolution 2048x1536 2048x1536 Native color resolution 8 bits / sub-pixel 8 bits / sub-pixel Pixel Pitch 0.207 mm (H) x 0.207 mm (V) 0.207 mm (H) x 0.207 mm (V) Active diagonal 528 mm (20.8 -inch) 528 mm (20.8 -inch) Display area (H x V) 423.9x318.0 (mm) 423.0x318.
Technical Specifications Item 82 MDCC 3120 MDCG 3120 USB standard USB 2.0 USB 2.
Technical Specifications Item MDCC 3120 MDCG 3120 Humidity 8% - 80% (non-condensing) for operation 5% - 95% (non-condensing) for storage 8% - 80% (non-condensing) for operation 5% - 95% (non-condensing) for storage Altitude 7500 m storage 3000 m operation 7500 m storage 3000 m operation 83
Technical Specifications (This page intentionally left blank.
Warranty Statement Warranty Statement BARCO MID GENERAL WARRANTY TERMS AND CONDITIONS Applicable from Jan 1st 2008 ARTICLE 1: PRODUCT WARRANTY Barco nv, Medical Imaging Division warrants that the equipment will be free of defects in workmanship or material for the warranty period or the specific period of a warranty extension program.
Warranty Statement Replacement parts used shall be new or equivalent to new parts for the revision level of the equipment. A replacement LCD panel will be new or similar run time. The warranty period for the replacement parts will expire at the same moment as the original warranty period of the equipment. All parts replaced hereunder and returned to Barco nv, MID (or an authorised service centre) shall become the property of Barco nv, MID (or the authorised service centre). 1.
Warranty Statement 2.5 Repair or replacement of consumables1 or specific parts that by definition are subject to wear and tear, including but not limited to: a.CRT’s, LCD panels b.Backlights in diagnostic LCD displays, when the backlight run time2 is beyond the Guaranteed Backlight Lifetime3 of that model, when used at the Factory Calibrated Luminance4 Eg1. • A display is used at 8 hours/day; ie. +/-2.
Warranty Statement Replacement of moveable parts such as power cords, remote controls, … 2.7 Any product disassembly and installation costs at the operation site, travel expenses and travel time to and from the operation site for the personnel in charge of the repair works and transport charges. 2.
Warranty Statement remedy and Barco's sole and exclusive liability for Barco’s breach of the Warranties hereunder. BARCO NV, MID SHALL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO CUSTOMER OR ANY THIRD PARTY FOR DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, SUCH AS BUT NOT LIMITED TO, DAMAGE TO OR LOSS OF TANGIBLE OR INTANGIBLE PROPERTY OR EQUIPMENT, LOSS OF PROFITS OR REVENUES, COST OF CAPITAL, COST OF PURCHASE OF REPLACEMENT GOODS, OR CLAIMS OF USER FOR SERVICE INTERRUPTIONS.
Warranty Statement (This page intentionally left blank.
Warranty Statement (This page intentionally left blank.
Warranty Statement (This page intentionally left blank.
Warranty Statement (This page intentionally left blank.
B410578-03 December 2010 Barco nv Medical Imaging President Kennedypark 35 B-8500 Kortrijk, Belgium www.barco.
