User Manual

CORONA S.BUS PROGRAMMING CARD CSBP-1 MANUAL

Thank you for purchasing CORONA's S.BUS programming card CSBP-1. CSBP-1 is а collection of S.BUS servo

programming, S.BUS decoder programming and up to eight-cell Li-Po battery pack voltage measurement function

handheld triple-function device.

Port description:

There are three modes in S.BUS programming card:

LED1 displays “А“ that indicate programming function of S.BUS servo.

LED1 displays “B” that indicate programming function of S.BUS decoder.

LED1 displays "С" that indicate voltage measuring of li-Po batteries.

When you need to measure the battery voltage you should not have the power port (4.8 - 6.0V) power on, and do

not plug in the device to bе programmed to avoid damage. After power left or right, click SW2 to select modes

from "А", "B" and "С".

MODE “A”:

1. Power on programming card. Let S.BUS servo connect to the programming interface. When the digital LED

displays "А", press the middle button of SW2, enter mode "А". When the right three digital LED display "-",

"-", "-" indicates servo has been linked. If not displayed, press the center button of SW2 again to link servos.

2. After а successful link, left or right click of sJr2 to select servo's parameters.

 LED1 display 1: Servo Reverse parameter is set to "О" indicates reverse turn "1" indicates а positive

tum. Left or right key click to switch through SW1. Servo writing bу pushing the middle button of SW1.

 LED1 display 2: Servo Channel number set (1-18: ch1- ch16, DG1 and DG2), left or right key click to

switch through SW1. Servo writing by pushing the middle button of SW1.

 LED1 display 3: Servo Right Travel Adjust (50%-175%), left or right key click to decrease or increase.

Servo writing by pushing the middle button of SW1.

 LED1 display 4: Servo Left Travel Adjust (50%-175%), left or right key click to decrease or increase

servo writing by pushing the middle button of SW1.

 LED1 display 5: Servo Neutral Offset (-30deg-+30deg), left or right key click to decrease or increase

servo writing by pushing the middle button of SW1.

 LED1 display 6: Servo travel range testing. SW1 Left key click indicate the smallest servo value output.

SW1 right key click indicate the largest servo value output. If you want the middle servo value output,

switch to other item except 6 and tum back.

3. When you push down SW1 to write parameters, the LED1..LED4 will fl 1 or 2 seconds, if the flash time is

longer than normal operation, please write the parameters again.

4. After write operation, you should repower on the programming card and link the servo to check all parameters

you have wrote.

PAGE 1
CORONA S.BUS PROGRAMMING CARD CSBP-1 MANUAL Thank you for purchasing CORONA's S.BUS programming card CSBP-1. CSBP-1 is а collection of S.BUS servo programming, S.BUS decoder programming and up to eight-cell Li-Po battery pack voltage measurement function handheld triple-function device. Port description: There are three modes in S.BUS programming card: LED1 displays “А“ that indicate programming function of S.BUS servo. LED1 displays “B” that indicate programming function of S.BUS decoder.
PAGE 2
MODE "B": 1. Power on the programming card, connect the S.BUS decoder to the- programming interface, switch to "B" By left or right key click of SW2. Push down the middle button of SW2 to link the decoder. If LED2 - LED4 display "-","-","-" indicate а successful link. If have no display, please link decoder again. 2. After а, successful link left or right key click of SW2 to change the physical port item. Port “1”: LED2 - LED4 display the servo channel number of port 1.