User Manual

ManualsBrandsCorona ManualsHobbyR6FA-SB 2.4Ghz FASST Compatible S.BUS Receiver

CORONA2.4GHzSpreadSpectrum(FASSTCOMPATIBLE)

ReceiverInstructionManualforR4FA‐SBandR6FA‐SB

Compatibility:

The CORONA 2.4GHz SpreadSpectrumFASST Compatible Receiver is designedfor use with FUTABA’s FASST

2.4GHz transmitters; including the 3PM,3PKS,3VCS,3GR,4PK(S),TM7, TM8, TM10, TM14 and the T6EX‐2.4G,

7C‐2.4G, 8FG, 10CG, 12FG. The R4FA‐SB and R6FA‐SB receivers supply a more useful mode for users. Both the

R4FA‐SB and

 R6FA‐SB support FUTABA’s FASST air system and surface system. The R4FA‐SB supports 7‐channel

withcontinuousPPM(positiveandnegative)output,RSSI outputandS.BUS output,R6FA‐SB supports6channel

highspeedPPM(HS)modetooptimizehelicopterresponsecontrolandS.BUSoutput.

UnderS.BUS output mode,both

R4FA‐SBand R6FA‐SB supply12 proportionalchannelsand 2 DGchannels.

Therefore,theR4FA‐SBorR6FA‐SBbecomes14‐channelreceiverswhenusingS.BUSoutput.



Specifications:

OperatingCurrent: 50mAmax

OperatingVoltage: 3.6~10V

Latency: R4FA‐SB’sdescription

 14mSforindependent4channeloutputandS.BUSoutput@FASSTmulti‐channelmode

 21mSforContinuousPPMoutput andRSSIoutput@FASSTmulti‐channelmode

 16mSforindependent4channeloutputandS.BUSoutput@FASST

7chmode

 24mSforContinuousPPMoutput andRSSIoutput@FASST7chmode

 14mSforindependent3channeloutput@FASSTsurfacesystemC1CODEmode

 R6FA‐SB’sdescription

 7mSforindependent6channel(HS)output@FASSTmulti‐channelmode

 14mSforindependent7channel(LS)outputandS.BUS

output@FASSTmulti‐channelmode

 8msforindependent6channel(HS)output@FASST7chmode

 16mSforindependent7channel(LS)outputandS.BUSoutput@FASST7chmode

 14msforindependent3channeloutput@FASSTsurfacesystemC1CODEmode



Sensitivity:  about‐100dBm

Operationtemperature:

‐10~80deg

C

Setup:

Bindprocedure:

 TurnontheFASSTtransmitter

 Connectthebatterytothereceiverwhilepressingthereceiver’sF/Sbutton.

 TheDual‐colorLED’swillcontinuouslycyclethroughthefollowing:

o RedLEDlight(searchingradiosignal)

o GreenLEDlight(acquiredtheradiosignal)

o RedLEDoff

(bindok)

o GreenLEDflashes10times(IDstoredinmemory)

o GreenLEDlightssolid(normaloperation)

Note:FASSTsurfacesystemstakeabitmoretimetocompletethebindprocedure.

Summary of content (3 pages)

PAGE 1
CORONA 2.4GHz Spread Spectrum (FASST COMPATIBLE) Receiver Instruction Manual for R4FA‐SB and R6FA‐SB Compatibility: The CORONA 2.4GHz Spread Spectrum FASST Compatible Receiver is designed for use with FUTABA’s FASST 2.4GHz transmitters; including the 3PM,3PKS,3VCS,3GR,4PK(S),TM7, TM8, TM10, TM14 and the T6EX‐2.4G, 7C‐2.4G, 8FG, 10CG, 12FG. The R4FA‐SB and R6FA‐SB receivers supply a more useful mode for users.
PAGE 2
Fail‐safe setting: There are two ways to set the Failsafe setting on the CORONA 2.4GHz Spread Spectrum FASST Compatible Receiver; 1. TX‐failsafe feature: This method sets the failsafe on the FASST transmitter and has priority (works on channel 3 only under FASST 7ch mode or on multiple‐channels under FASST multi‐channel mode) while the receiver is on, just like FUTABA receivers (only available on FASST air system). 2.
PAGE 3
^2 refer the signal description picture below ^3 refer the signal description picture below RSSI PWM out define: Pulse width from about 900uS~ 2100uS to indicate RSSI strength from ‐100dBm~‐40dBm. Important Note: If you are using analog servos in your model you must keep your receiver under the factory settings (normal output mode) or your analog servo will get hot and possibly burn out. As well you cannot use a non S.BUS servo on a channel while S.BUS signal output present.