User's Manual

ManualsBrandsCorning Optical Communication Wireless ManualsElectronicsVE LTE 700MHz MIXED BAND MIMO

Table Of Contents

Preface Material
Policy for Warrantee and Repair
General Warranty
Specific Product Warranty Instructions
Returns
Limitations of Liabilities
Reporting Defects
Safety Warnings
Compliance with RF Safety Requirements
Certification and Compliance to Standards
About This Guide
List of Acronyms
Table of Contents
1 Overview
- 1.1 Key Features and Capabilities
- 1.2 System Architecture
- 1.3 System Elements
  - 1.3.1 VE Control Unit (VCU)
    - 1.3.1.1 VCU Front Panel
    - 1.3.1.2 VCU Rear Panel
  - 1.3.2 VE Access Pod (VAP)
- 1.4 System Monitoring and Management
  - 1.4.1 Integration with an External Fault Management System
2 Installation Workflow
3 Infrastructure Requirements and Layout Planning
- 3.1 General Information on Location and Connections
- 3.2 Infrastructure Requirements
- 3.3 Coverage and Installation Planning
  - 3.3.1 Types of Environments
- 3.4 Planning VAP Layout
4 VCU Unit Installation and Provisioning
- 4.1 VCU Kit Contents
- 4.2 VCU Physical Installation
  - 4.2.1 Master VCU Installation
    - 4.2.1.1 Master/Stand-Alone VCU Alarm Output Connections
  - 4.2.2 Slave VCU Installation
- 4.3 Ethernet Cable Connections to VAPs
  - 4.3.1 Shifting Relevant Ethernet LAN Connections
  - 4.3.2 Operation with LAN utilizing Power over Ethernet (PoE)
- 4.4 Provisioning the VE Control Unit
5 VAP Installation and Provisioning
- 5.1 VAP Installation
- 5.2 Desk and Wall Mount VAP Installations
- 5.3 Verifying VAP Coverage Area
- 5.4 Naming the VAPs, Verifying Connections and Monitoring
- 5.5 Provisioning the VAPs
  - 5.5.1 Verifying Normal VAP Operation
  - 5.5.2 Naming the VAP
6 Navigating the Web Access Application
- 6.1 Opening a Session and Authentication Levels
- 6.2 About the MobileAccessVE Web Access Window
- 6.3 Configuration Tab
  - 6.3.1 Network Topology Tree
    - 6.3.1.1 Removing Network Element from Baseline
  - 6.3.2 Configuration Display Area
- 6.4 Management Tab
7 VCU Monitoring and Configuration
- 7.1 Viewing VCU General Information
- 7.2 Viewing VCU Alarms
- 7.3 Master VCU RF Parameters
8 VAP Monitoring and Configuration
- 8.1 Viewing VAP General Information
- 8.2 Viewing VAP Alarms
- 8.3 VAP RF Parameters
9 Administrative Operations
- 9.1 Changing Password
- 9.2 Retrieving VCU IP Address
- 9.3 IP Settings
- 9.4 SNMP Configuration Parameters
- 9.5 Upgrading (or Downgrading) VCU and VAP Software
  - 9.5.1 Upgrading the VAP SW
  - 9.5.2 Upgrading the VCU SW
10 Troubleshooting
- 10.1 Finding a Specific VAP in the Building
- 10.2 Wireless Service is Not Available
- 10.3 PoE is Not Working
- 10.4 Ethernet Service is Degraded
- 10.5 No Service from Connected Access Pod
- 10.6 VCU Cannot be monitored via SNMP
Appendix A - Traps
Appendix B – MobileAccess VE MIB Tree Structure (Version 1.8)
- MobileAccess Version 1.13 MIBs/OID Descriptions

VCU Unit Installation and Provisioning

Mixed Band LTE 700 MHz MobileAccessVE Instant Coverage Solution User Manual 31

4.4.3 Setting RF Parameters

In a Master-Slave mode (multi-tier architecture) the RF parameters are only configured for the

Master VCU unit.

The VCU supports both the Lower A,B,C and Upper C LTE bands in MIMO and SISO

configurations. Each MIMO and SISO band can be individually configured in dedicated tabs.

This section describes the MIMO and the SISO configuration procedures.

To Configure the RF Parameters:

1. Select the Master VCU in the topology tree and then select the Service RF tab.

Note 1: The Type field (Read Only) corresponds to the Product Type selected in the

Module

Info

tab and shows the supported LTE 700 MHz Band (Upper C or Lower A,B,C).

Note 2: The DL CF parameter is Read Only and pre-defined for the supported 10MHz block.

In MIMO configurations, the same DL CF frequency from the Base Station is defined for

Service1 and Service2.

2. Define the BTS Connenction according to type of RF connections (simplex/duplex)

performed between the VCU and the RF Source. Default setting = duplex.

3. Define Max expected power of BTS (0-33dBm).

4. Define UL System Gain (-15 to 5dB)

Notes: Max expected Pin parameter can be obtained from your service provider. The remaining

parameters are predefined to their default values. (Service Bandwidth is set to 10MHz per

channel). Any updates of the service definition (Service Mode) are sent to all connected VAPs.