User Manual
Table Of Contents
- Warranties
- Hardware
- Software Warranty
- Notwithstanding the foregoing, Corning shall have no obligation under the Software Warranty if the
- Returns
- Limitations of Liabilities
- Reporting Defects
- Warnings and Admonishments
- RF Safety
- Compliance with RF safety requirements:
- Power requirements for DC Inputs
- Laser Safety
- Care of Fiber Optic Connectors
- Regulatory Compliance Information
- Standards and Certifications
- Licensee Contact Information
- About this Guide
- Additional Relevant Documents
- List of Acronyms
- Table of Contents
- 1.1 Key Features and Capabilities
- 1.2 System Architecture
- 1.3 System Monitoring and Management
- 1.4 HX Unit Description
- 1.5 External Passive Module (EPM)
- 1.6 Site Considerations
- 1.7 Environmental
- 1.8 Installation Requirements
- 1.9 Fiber Optic Requirements
- 1.10 RF Coaxial Cable Guidelines
- 1.11 Antenna Specifications and Guidelines
- 1.12 Grounding Requirement
- 1.13 Manual Handling
- 1.14 Installation Requirements
- 1.15 Unpacking and Inspection
- 1.16 Mounting
- 1.17 Connections
- 1.18 Verifying Normal Operation
- Appendix A: System Specifications
- RF Parameters
- Supported Services
- RF Parameters per Service Antenna Port
- RF Parameters for Diplexer External Input Port
- Physical Specifications
- Standards and Approvals
- Appendix B: Ordering Information
- MobileAccessHX WCS Remote Units
Warnings and Admonishments
P/N 709C015102
Page 5
Warnings and Admonishments
There may be situations, particularly for workplace environments near high-powered RF sources, where
recommended limits for safe exposure of human beings to RF energy could be exceeded. In such cases,
restrictive measures or actions may be necessary to ensure the safe use of RF energy.
The equipment has been designed and constructed to prevent, as far as reasonably, practicable danger. Any
work activity on or near equipment involving installation, operation or maintenance must be, as far as reasonably,
free from danger.
Where there is a risk of damage to electrical systems involving adverse weather, extreme temperatures, wet,
corrosive or dirty conditions, flammable or explosive atmospheres, the system must be suitably installed to
prevent danger.
Equipment provided for the purpose of protecting individuals from electrical risk must be suitable for the purpose
and properly maintained and used. This covers a range of activities including lifting, lowering, pushing, pulling,
carrying, moving, holding or restraining an object, animal or person from the equipment. It also covers activities
that require the use of force or effort, such as pulling a lever, or operating power tools.
Where some of the abovementioned activities are required, the equipment must be handled with care to avoid
being damaged.
Observe standard precautions for handling ESD-sensitive devices. Assume that all solid-state electronic devices
are ESD-sensitive. Ensure the use of a grounded wrist strap or equivalent while working with ESD-sensitive
devices. Transport, store, and handle ESD-sensitive devices in static-safe environments.
RF Safety
WARNING! To comply with FCC RF exposure compliance requirements, each individual antenna used for this
transmitter must be installed to provide a separation distance greater than 115 cm or more from all persons during
normal operation and must not be co-located with any other antenna for meeting RF exposure requirements.
WARNING! Antenna gain should not exceed 12.5 dBi.
WARNING! Each individual antenna used for this transmitter must be installed to provide a separation distance
greater than 115 cm or more from all persons and must not be co-located with any other antenna for meeting RF
exposure requirements.
WARNING! The design of the antenna installation needs to be implemented in such a way so as to ensure RF
radiation safety levels and non-environmental pollution during operation.
Compliance with RF safety requirements:
• Corning products have no inherent significant RF radiation.
• The RF level on the downlink is very low at the downlink ports. Therefore, there is no dangerous RF radiation
when the antenna is not connected.
Power requirements for DC Inputs
WARNING! Only use a special DC supply cable with connector
WARNING! Always keep DC IN connectors connected during the product operation