STARBUCKS UC100 PROGATE Operator’s Manual Release Date: January 24, 2008 Publication Number: 621054211OPR Revision Date: April 07, 2014 Revision: B Visit the Cornelius web site at www.cornelius.com for all your Literature needs.
The products, technical information, and instructions contained in this manual are subject to change without notice. These instructions are not intended to cover all details or variations of the equipment, nor to provide for every possible contingency in the installation, operation or maintenance of this equipment. This manual assumes that the person(s) working on the equipment have been trained and are skilled in working with electrical, plumbing, pneumatic, and mechanical equipment.
TABLE OF CONTENTS Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Read and Follow all Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recognize Safety Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Different Types of Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Tips . . . . . . . . . . . . . . . . . .
UC100 ProGate Operator’s Manual SAFETY INSTRUCTIONS Read and Follow all Safety Instructions Read and follow all safety instructions in this manual and on the machine (decals, labels, and laminated cards). Read and understand all applicable OSHA (Occupation Safety and Health Administration) safety regulations before operating the machine. Recognize Safety Alerts This is the safety alert symbol.
UC100 ProGate Operator’s Manual IMPORTANT: Disconnect power to the dispenser before servicing or cleaning. NEVER: place hands inside of hopper or gate area without disconnecting power to the dispenser. Agitator rotation occurs automatically when dispenser is energized! ALWAYS: be sure the removable lid is properly installed to prevent unauthorized access to the hopper interior and possible contamination of the ice. ALWAYS: be sure the upper and lower front panels are securely fastened.
UC100 ProGate Operator’s Manual LOC (Lock) When displayed, check to make sure that ice bin covers, ice chute transition, piece ice flapper and ice chute are attached properly. Once secured, push the “M” button on the keypad to return to dispense mode. FILL When displayed, all ice has been consumed and needs to be replaced. Refill the ice bin. Close all ice bin covers and push the “M” button on the keypad to return to dispense mode. ERR (Error) When displayed, a system fault has occurred.
UC100 ProGate Operator’s Manual 2. 3. 4. 5. 6. 7. The current default table is displayed in the menu. The arrow buttons can now be used to move through the four tables. To exit without programming, press and hold the “P” button for three (3) seconds to exit. To reset to a new table, select the table using the arrow buttons. Press and hold the “M” button for three (3) seconds, the display flashes twice when the new setting is accepted. Exit by pressing and holding the “P” button for three (3) seconds.
UC100 ProGate Operator’s Manual Daily (or as required) Remove foreign material from vending area drip tray to prevent drain blockage. Clean vending area. Check for proper water drainage from the vending area drip tray. Cleaning Exterior Surfaces IMPORTANT: Perform the following daily. 1. 2. Remove the cup rest from drip tray. Wash the drip tray with soap solution. Rinse with potable water and allow solution to run down the drain. CAUTION — Do not pour hot coffee or other hot liquids into the drip tray.
UC100 ProGate Operator’s Manual Ice Chute Maintenance IMPORTANT: Perform the following daily. NOTE: The ice chute has a built in safety feature which disables the unit when the ice chute cover is removed. If the ice chute cover is not properly installed, the agitator and ice chute gate will not function. 1. Press and hold the “P” and “UP” buttons for five (5) seconds to enter purge mode. LED displays “Purg”. 2.
UC100 ProGate Operator’s Manual Ice Chute Cover Locking Tab Ice Chute Cover Figure 4 Monthly Maintenance Clean and sanitize the hopper interior and auger assembly. Cleaning Interior Surfaces CAUTION: When pouring liquids into the hopper, do not exceed the rate of 1/2 gallon per minute. IMPORTANT: Perform the following procedure at least once a month. 1. 2. 3. 4. 5. Open right hand hopper cover and remove all ice from hopper. Remove the agitator disk and agitator assembly. Remove the tower cover.
UC100 ProGate Operator’s Manual certain that the auger slips into it drive pin. Auger transition cap will not assemble properly if the auger is not seated on its drive pin. 11. 12. Reinstall the two auger tube halves. Replace the auger transition cap onto the auger and lock it down by snapping the retaining bail onto the auger transition cap. Reinstall the tower cover. 13. Close the hopper access cover.
UC100 ProGate Operator’s Manual TROUBLESHOOTING IMPORTANT: Only qualified personnel should service internal components or electrical wiring. WARNING: If repairs are to be made to the CO2 or air system, stop dispensing, shut off the CO2 or air supply, then relieve the system pressure before proceeding. If repairs are to be made to the ice dispensing system, make sure electrical power is disconnected from the unit.
UC100 ProGate Operator’s Manual Publication Number: 621054211OPR - 10 - © 2008-2014, Cornelius Inc.
Cornelius Inc. www.cornelius.
