S6161-UG-FSE-010 0910-LP-108-4884 Revision 2 TECHNICAL MANUAL FOR ICE MAKER, DISPENSER, IMD SERIES DESCRIPTION, OPERATION, AND MAINTENANCE Supersedure Notice: This manual supersedes S6161-UG-FSE-010 Revision 1, dated 12 September 2001, and all changes thereto. “Distribution Statement “A”: Approved for public release; distribution is unlimited.
S6161-UG-FSE-010 0910-LP-108-4884 Revision 2 TECHNICAL MANUAL FOR ICE MAKER, DISPENSER, IMD SERIES DESCRIPTION, OPERATION, AND MAINTENANCE Supersedure Notice: This manual supersedes S6161-UG-FSE-010 Revision 1, dated 12 September 2001, and all changes thereto. “Distribution Statement “A”: Approved for public release; distribution is unlimited.
S6161-UG-FSE-010 30 April 2009 IDENTIFYING TECHNICAL PUBLICATION SHEET FOR COMMERCIAL MANUAL Supersedure Notice: This manual supersedes S6161-UG-FSE-010 Revision 1, dated 12 September 2001, and all changes thereto. 1. PURPOSE: This technical publication sheet is issued for the purpose of identifying and authorizing the following commercial manual for Navy use. Manufacturer: IMI Cornelius, Inc., 101 Broadway Street West, Osseo, MN 55369 Purchase Order or Contract No.: N00024-05-C-2115 Requisition No.
Table of Contents Part Title I. Countertop Icemaker IMD Series, Installation Manual II. Countertop Icemaker IMD Series, Illustrated Parts Breakdown III.
PART I Countertop Icemaker IMD Series, Installation Manual
Part I ® COUNTERTOP ICEMAKER IMD Series Installation Manual Release Date: April 8, 2004 Publication Number: 638085277INS Revision Date: February 16, 2009 Revision: C Visit the IMI Cornelius web site at www.cornelius.com for all your Literature needs.
Part I COUNTERTOP ICEMAKER IMD SERIES INSTALLATION MANUAL The products, technical information, and instructions contained in this manual are subject to change without notice. These instructions are not intended to cover all details or variations of the equipment, nor to provide for every possible contingency in the installation, operation or maintenance of this equipment.
Part I TABLE OF CONTENTS Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Read and Follow all Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recognize Safety Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Part I Electrical Checkout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overload Check - FIGURE 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compressor Check - FIGURE 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Capacitor Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting Gear Motors . . . . . . . . . . . . .
Part I Countertop Icemaker IMD Series Installation Manual SAFETY SAFETY INSTRUCTIONS Read and Follow all Safety Instructions Read and follow all safety instructions in this manual and on the machine (decals, labels, and laminated cards). Read and understand all applicable OSHA (Occupation Safety and Health Administration) safety regulations before operating the machine. Recognize Safety Alerts This is the safety alert symbol.
Part I Countertop Icemaker IMD Series Installation Manual SPECIFICATION CHART Models IMD300-15A IMD302-15A IMD300-30A IMD300-30W IMD301-30A IMD301-30W IMD302-30A IMD302-30W IMD600-30A IMD600-30A IMD601-30A IMD601-30W IMD602-30W IMD600-90A IMD600-90W IMD601-90A IMD601-90W IMD602-90A IMD602-90W Condensing Unit Air Cooled Air Cooled Air Cooled Water Cooled Air Cooled Water Cooled Air Cooled Water Cooled Air Cooled Water Cooled Air Cooled Water Cooled Water Cooled Air Cooled Water Cooled Air Cooled Water Cool
Part I Countertop Icemaker IMD Series Installation Manual S HIP P ING WT. (IMD300-- 30) 220 L B S . (A P P R OX.) S HIP P ING WT. (IMD600-- 30) 240 L B S . (A P P R OX.) FIGURE 2. DIMENSION DRAWINGS (30 LBS.) IMD 300-30 AND IMD 600-30 S HIP P ING WT. 225 L B S . (A P P R OX.) FIGURE 3. DIMENSION DRAWINGS (90 LBS.) IMD600-90 © 2004-2009, IMI Cornelius Inc.
Part I Countertop Icemaker IMD Series Installation Manual INSTALLATION INSTRUCTIONS REMOVE ICEMAKER FROM CARTON 1. 2. Keep unit in the upright position, remove carton and pallet from unit and inspect unit for damage. Upon inspection of unit, if any damage is found, file a claim with carrier immediately. Locate Startup Card either on outside of container or on plastic liner. Fill in proper information and send one copy to factory, and other copy to Distributor. Postage is prepaid. CABINET REMOVAL 1. 2. 3.
Part I Countertop Icemaker IMD Series Installation Manual DRAIN CONNECTION 1. 2. 3. 4. 5. 6. Install splash panel on machine and hold in place with (2) screws. Do not tighten at this time. Remove drain tray mounting bracket from their shipping carton. Clip the drain try mounting bracket onto the bottom of the splash panel in the brackets provided. Hook the drain tray into the splash panel and onto the mounting bracket. Push the drain elbow securely onto the drain tray. Do not glue in place.
Part I Countertop Icemaker IMD Series Installation Manual Low Water Safety Control - Adjust magnet by bending magnet arm as shown in FIGURE 4 to shut down unit if the water level drops below the line on the side of the reservoir. Bin Control - Remove four screws from top of bin cover and lift cover so bin control plate can be manually lifted until unit shuts down.
Part I Countertop Icemaker IMD Series Installation Manual GUIDE TO SERVICE ICEMAKER CLEANING AND SANITIZING PROCEDURES Do not use any of the ice made during cleaning operations. Clean and sanitize ice storage area when cleaning icemaker. 1. 2. 3. 4. 5. 6. 7. 8. 9. Turn machine off. Shut off water supply. Remove ice from storage bin. Mix approved cleaner (2 gallons as directed). Recommended cleaner: Calgon Corp. of Virginia Chemicals, ice machine cleaner. Mixture: 3-1/3 ounces per gallon of water.
Part I Countertop Icemaker IMD Series Installation Manual SEMI-ANNUALLY Semi-Annually in addition to all previously established service procedures perform the following: 1. 2. 3. 4. 5. 6. 7. Check for water leaks in tube connections, water fittings, and lower icemaker water seal. Check drain tubes for clogs and “aged” tubes. Replace if tubes are stained or brittle. Check for signs of condensation. Clean where necessary and replace insulation properly. Check safety circuits for proper operation.
Part I Countertop Icemaker IMD Series Installation Manual WATER LEVEL CONTROL HOW WATER LEVEL CONTROL WORKS When water is introduced through the inlet fitting the float rises. The float pushes against a lever which in turn forces the poppet assembly against the inlet fitting valve seat which seals the water off, (see FIGURE 4). Before the water inlet is sealed the safety switch is operated. In the event of a water failure the float would drop down and operate the safety switch to shut off the machine.
Part I Countertop Icemaker IMD Series Installation Manual The operating positions of the switch are fixed, no adjustments are necessary. If switch replacement becomes necessary, simply disconnect cable at connector, remove wires from switch. Temperature/Pressure Charts* Air Temperature 10 lbs.
Part I Countertop Icemaker IMD Series Installation Manual NOTE: On water cooled units adjust condenser modulating valve before troubleshooting expansion valve. CAUTION: Very high discharge pressure is present in system. Quick disconnects on your gages will minimize Danger and loss of refrigerant. Comply with federal regulations for reclaiming refrigerant.
Part I Countertop Icemaker IMD Series Installation Manual GEAR MOTOR The gear motor is equipped with a start relay and a manual reset overload. When current is applied, the relay energizes and completes the circuit to the start winding. The motor reaches a predetermined speed and the relay drops out, disconnecting the start winding. The run winding remains in the circuit as long as current is applied.
Part I Countertop Icemaker IMD Series Installation Manual AUGER & EXTRUDING HEAD REMOVAL 1. 2. 3. 4. 5. Disconnect unit from power supply. Remove storage container cover and put aside. Turn off water supply to icemaker. After ice has melted from head take hold of the auger nut and lift straight up to disengage from icemaker. When replacing the auger assembly, make certain that both the auger engages the output shaft drive and the extruding head ribs engage the evaporator tube collar. See FIGURE 8.
Part I Countertop Icemaker IMD Series Installation Manual TO REPLACE BEARINGS 1. 2. 3. 4. 5. 6. 7. Dispense all ice from unit. Disconnect unit from electrical power. Remove panels. Unplug Dispense Motor and Ice Level Switch. Remove four screws holding dispense cover in place. Remove dispense cover assembly. Use an open end wrench on auger nut connected to bearing and turn and turn counterclockwise to remove assembly. 8. Remove worn bearings. Replace with new bearings and then reinstall assembly.
Part I Countertop Icemaker IMD Series Installation Manual OVERLOAD CHECK - FIGURE 10 4. Using a volt-ohm meter check the continuity across the overload, contacts #1 & #3. If none, wait for unit to cool down and try again. If still no continuity, the overload protector is defective and should be replaced. COMPRESSOR CHECK - FIGURE 11 The resistance readings on the windings will be between 0.25 and 10.00 ohms, a meter capable of these low readings must be used. 5. 6. 7. 8. Check between “C” & “R”.
Part I Countertop Icemaker IMD Series Installation Manual Motor Check The resistance readings on the windings will be between 5 to 25 ohms. A meter capable of these low readings must be used. The Start Relay cover must be removed. If no continuity on start or run winding test, replace stator. If continuity on grounded motor test, replace stator. FIGURE 12. PIN NUMBERS Publication Number: 638085277INS - 16 - © 2004-2009, IMI Cornelius Inc.
Part I Countertop Icemaker IMD Series Installation Manual SAFETY CONTROLS Your Icemaker unit has several safety and control devices incorporated into its design. WARNING: None of the below described devices should ever be “bypassed” to allow the unit to function. The safety and control system shut-off devices are: FIGURE 13. 1. 2. 3. 4. 5. 6. Low water shut off reed switch located in icemaker float assembly. (Automatic reset type). Gear motor thermal overload, manual reset type (red button on motor).
Part I Countertop Icemaker IMD Series Installation Manual GUIDE TO GOOD ICE CUSTOMER COMMENTS “It runs but the ice is too soft.” “The icemaker is not producing enough ice.” CHECK ICEMAKER LOCATION CONDITIONS FIRST • Proper air flow for condensing system. • Location too close to high units such as coffee urns, deep fryers, grills, etc. • Supply water conditions Water too warm (above 90oF. “The ice is too wet.” Water artificially softened above 262 ppm sodium chloride.
© 2004-2009, IMI Cornelius Inc. Too much refrigerant in system. Evacuate and recharge system. Clean condenser. Non-condensible in system. Check electrical wiring in con trol box for loose connec tions. Check for failed service switch or relay. Check power to machine. NO POWER - 19 Plugged liquid line dryer. Replace dryer. Evacuate and recharge system. Check for leaks. Condenser dirty or restricted. Low on refrigerant. Check electrical circuit to fan motor. Check fan motor.
Part I Countertop Icemaker IMD Series Installation Manual BLK 1 2 ICE SELECT BRN LIGHT WHT YLW 4 1 DISP. SWITCH WHT 2 LIGHT WATER SELECT BRN BLK YLW DISPENSE MOTOR WHT YLW BLK YLW BRN BLK RED BLU WHT ORG YLW BRN GRN BRN GRN GRY 3 BRN ORG BLU WATER VALVE DRINK FRONT OPTION 1 WHT BLK 5 RED 1 3 4 SERVICE SWITCH BLK BLK WHT BLK BLK GRN 6 WHT WHT 2 ANTI-FREEZE RELAY WHT ELECTRICAL BOX 2 3 LOW WATER ICE LEVEL FAN COMP.
Part I Countertop Icemaker IMD Series Installation Manual FIGURE 15. SCHEMATIC IMD 300-30, IMD 600-30, IMD 601-30, IMD 600-90, AND IMD 601-90 © 2004-2009, IMI Cornelius Inc.
Part I Countertop Icemaker IMD Series Installation Manual FIGURE 16. SCHEMATIC IMD 302-30, IMD 602-30, AND IMD 602-90 Publication Number: 638085277INS - 22 - © 2004-2009, IMI Cornelius Inc.
Part I IMI Cornelius Inc. www.cornelius.
Part I
PART II Countertop Icemaker IMD Series, Illustrated Parts List
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST COUNTERTOP ICEMAKER IMD SERIES IMD Series 1 of 30 Manual Part No.: 638085277IPL Rev: C February 18, 2009 © IMI Cornelius Inc.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST 2 1 3 5 10 8 9 4 7 6 IMD 300-15 CABINET PARTS ASSEMBLY AND PARTS LIST Item Part No. No.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST 2 1 3 5 4 11 7 8 9 10 6 IMD 300-30 AND IMD 600-30 CABINET PARTS ASSEMBLY AND PARTS LIST Item Part No. No.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST 2 1 3 5 7 8 9 4 10 6 IMD 600-90 CABINET PARTS ASSEMBLY AND PARTS LIST Item Part No. No. 1 638032539 2 638032537 3 638032538 Name Panel Left Side Panel Top Panel Right Side 4 638032040-006 Panel Splash Asm. - Push Button * 5 * 638032541-001 638032536-002 638032536-001 638032548 638059270 638058805 638032531 638033508 638033509 638032531-001 Panel Splash Asm.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST 9 10 13 14 15 16 8 7 18 19 20 21 22 2 23 1 17 12 3 4 6 REFRIGERATION AND FRAME ASSEMBLY IMD 300-15 IMD Series 5 of 30 Manual Part No.: 638085277IPL Rev: C February 18, 2009 © IMI Cornelius Inc.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST REFRIGERATION AND FRAME ASSEMBLY IMD300-15 Item Part No. No.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST 9 8 11 7 6 2 1 10 3 4 5 10 REFRIGERATION AND FRAME ASSEMBLY IMD 300-30 AND IMD 600-30 IMD Series 7 of 30 Manual Part No.: 638085277IPL Rev: C February 18, 2009 © IMI Cornelius Inc.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST REFRIGERATION AND FRAME ASSEMBLY IMD 300-30 AND IMD 600-30 Item No. Part No. Item No.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST 3 4 5 6 7 9 1 2 8 REFRIGERATION AND FRAME ASSEMBLY IMD 600-90 IMD Series 9 of 30 Manual Part No.: 638085277IPL Rev: C February 18, 2009 © IMI Cornelius Inc.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST REFRIGERATION AND FRAME ASSEMBLY IMD 600-90 Item No. Part No. Item No. Name Part No. Name 1 638036273 638036272 Condenser Air Cooled Condenser Water Cooled 8 638090625 638090625-002 2 638090635 Shroud Condenser * 164980002 Electrical Box Asm. (115V) Electrical Box Asm.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST WATER CONTROL ASSEMBLY AND PARTS LIST IMD 300-15 1 2 3 Item No. Part No. Name 1 630900548 Water Level Control Assy. 2 638008483-06 Reed Switch Assy. 3 638030024 Brkt - Water Level IMD Series 11 of 30 Manual Part No.: 638085277IPL Rev: C February 18, 2009 © IMI Cornelius Inc.
Part II
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST WATER CONTROL ASSEMBLY AND PARTS LIST IMD 600-90 1 2 3 Item No. Part No. Name 1 630900548 Water Level Control Assy. 2 638008483-03 Reed Switch Assy. 3 638030024 Brkt - Water Level IMD Series 13 of 30 Manual Part No.: 638085277IPL Rev: C February 18, 2009 © IMI Cornelius Inc.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST ICE LEVEL CONTROL ASSEMBLY IMD 300-15 2 13 4 3 Ground 8 1 6 7 12 9 11 10 5 Top View 4 24 14 23 17 16 22 15 21 19 18 20 Side View Manual Part No.: 638085277IPL Rev: C February 18, 2009 © IMI Cornelius Inc.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST ICE LEVEL CONTROL ASSEMBLY IMD 300-15 Item No. Part No. Item No. Name 2 638032760 638032760-002 638032759 3 638007051-08 4 638007204-06 5 6 7 8 9 10 11 638032748 638003924 638032745 638007002-12 638007341-10 638032771 638007009-02 Gear Motor Dispense (115V) Gear Motor Dispense (220V) Spacer Eyelet Screw No.10-32 X 5/8” Long BHMS Nut No.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST 2 1 8 21 20 24 TOP VIEW ICE LEVEL CONTROL ASSEMBLY IMD 300-30 AND 600-30 PART NUMBER 638031494-001 (115V) AND 638031494-002 (220V) 6 7 3 17 10 4 11 5 16 9 12 22 14 15 13 25 19 23 18 SIDE VIEW ICE LEVEL CONTROL ASSEMBLY IMD 300-30 AND 600-30 PART NUMBER 638031494-001 (115V) AND 638031494-002 (220V) Manual Part No.: 638085277IPL Rev: C February 18, 2009 © IMI Cornelius Inc.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST ICE CONTROL LEVEL ASSEMBLY IMD 300-30 AND IMD 600-30 Item Part No. No. 1 638031075 2 638031493-001 638031493-002 3 638031077 4 638031011 5 638031156 6 638011396 7 638007308-01 8 638007009-10 9 638031010 10 638031014 11 638007337-02 12 638031146 13 638031150 Name Top Cover Outside Dispense Motor Asm. (115V) Dispense Motor Asm.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST 1 2 20 3 19 5 9 6 7 8 10 11 12 10 13 11 11 14 11 12 14 15 13 11 TOP VIEW ICE LEVEL CONTROL ASSEMBLY IMD 600-90 6 27 7 20 8 26 29 28 8 30 2 16 19 18 17 24 21 33 37 34 35 22 31 23 25 32 19 36 38 39 SIDE VIEW ICE LEVEL CONTROL ASSEMBLY IMD 600-90 Manual Part No.: 638085277IPL Rev: C February 18, 2009 © IMI Cornelius Inc.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST ICE LEVEL CONTROL ASSEMBLY IMD 600-90 Item No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Part No. 638031893 638036605 638036645 638009062-02 638036604 01470 638007052-02 638000845 638036587-01 638031849 638031849 638005633 00885 168833003 638007206-07 638007088-06 638036651 638036577 638007108-01 164005001 638036938 638036123 638036603 IMD Series Name Insulated Bin Cover Asm.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST 13 12 11 10 BIN AND FRONT END ASSEMBLY IMD 300-15, IMD 300-30, AND 600-30 Manual Part No.: 638085277IPL Rev: C February 18, 2009 © IMI Cornelius Inc.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST BIN AND FRONT END ASSEMBLY IMD 300-15, IMD 300-30 & IMD 600-30 Item 300-15 No. Part No.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST 21 22 28 12 11 20 19 10 9 18 8 14 15 5 7 17 4 3 16 13 1 2 6 25, 26 24, 27 23 BIN AND FRONT END ASSEMBLY IMD 600-90 Manual Part No.: 638085277IPL Rev: C February 18, 2009 © IMI Cornelius Inc.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST BIN AND FRONT END ASSEMBLY IMD 600-90A Item No. 1 * * * Part No. 638090001 630900531 6380900422 638011645 638011647 638011647 Item No. Name Gearmotor (115V) see note Gearmotor (208V) see note Gearmotor (220V) see note Cable Assembly Gearmotor 115V Cable Assembly Gearmotor 208V Cable Assembly Gearmotor 220V Part No.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST ELECTRICAL BOX ASSEMBLY IMD 300-15 AND IMD 302-15 Item No. 1 2 3 4 5 6 Part No. 638032794 163529000 638004791 638007051-06 638007030-02 638004402 638010018 IMD Series Name Electrical Box Bushing Switch Toggle Screw No.10-32 X 3/8” Screw No.8 X 5/8” Relay 115V Relay 220V 25 of 30 Item No. 7 8 * * * Part No.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST 7 1 9 6 2 3 4 10 12 13 11 8 5 ELECTRICAL BOX ASSEMBLY IMD 300-30, IMD 600-30, AND IMD 600-90 (ALL VOLTAGES) Manual Part No.: 638085277IPL Rev: C February 18, 2009 © IMI Cornelius Inc.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST Electrical Box Assembly IMD300-30, IMD600-30 and IMD600-90 Item No. 1 Part No. 638031001 638035039 2 638031003 638031205 Item No. Name Part No. 638011620 Electrical Box Name Cable Assem.
Part II
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST DISPENSE MECHANISM ASSEMBLY IMD 300-15, IMD 300-30, IMD 600-30 & IMD 600-90 Item No. Part No. 638031035 Name 1 638031505 Bracket Solenoid Mounting (115V) Bracket Solenoid Mounting (208V) 2 638010081 638031499-001 638010019 Solenoid (115V) Solenoid (208V) Solenoid (220V) 3 638007051-02 Screw No.
Part II IMI CORNELIUS INC. Telephone 1-800-238-3600 www.cornelius.com ILLUSTRATED PARTS LIST GEAR MOTOR ASSEMBLY WIRE DIAGRAM (ALL VOLTAGES) EXPLODED VIEW Manual Part No.: 638085277IPL Rev: C February 18, 2009 © IMI Cornelius Inc.
PART III Countertop Icemaker IMD Series, Certification Data Sheets
Part III
Part III
Part III
Part III
Ref: NAVSEAINST 4160.3A NAVSEA S0005-AA-GYD-030/TMMP NAVSEA/SPAWAR TECHNICAL MANUAL DEFICIENCY/EVALUATION REPORT (TMDER) INSTRUCTIONS: Continue on 8 ½” x 11” page if additional space is needed. 1. Use this report to indicate deficiencies, problems and recommendations relating to publications. 2. For CLASSIFIED TMDERs see OPNAVINST 5510H for mailing requirements. 3. For TMDERs that affect more than one publication, submit a separate TMDER for each. 4. Submit TMDERs at web site https://nsdsa2.phdnswc.navy.
FOLD HERE AND TAPE SECURELY PLEASE DO NOT STAPLE INCLUDE COMPLETE ADDRESS USE PROPER POSTAGE FOR OFFICE USE ONLY COMMANDER CODE 310 BLDG 1389 NAVSURFWARCENDIV NSDSA 4363 MISSILE WAY PORT HUENEME, CA 93043-4307 FOLD HERE AND TAPE SECURELY PLEASE DO NOT STAPLE
S6161-UG-FSE-010 Revision 2
