XD730.400 Piezo Objective Scanner User Manual Version: V1.0 This document describes the following products: ■ XD730.400S-B1 ■ XD730.
DECLARATION Thank you for choosing Coremorrow's products! This user manual is applicable to XD730.400 series piezo objective scanner. For your smooth and correct use of this product, please read this manual carefully before use. Please follow the instructions in the manual installation and use procedures. Improper operation may cause injury to the operator or damage to the product.
Contents 1. Introduction ........................................................................................................................................2 1.1 Purpose and content ................................................................................................................2 1.2 Symbol and meaning................................................................................................................2 1.3 Expected reader .......................................................
XD730.400 Piezo Objective Scanner User Manual 1. Introduction 1.1 Purpose and content The manual is mainly for your smooth and correct use of piezo objective scanner. The manual contains all necessary information for XD730.400. The manual describes the precautions during installation and use. 1.2 Symbol and meaning DANGER: Improper handling may could cause injury to the operator. Attention: Improper handling can cause damage to the equipment. No order between items. 1. 2. Please operating in order.
2. Safety Guide XD730.400 piezo objective scanner is designed with advanced technology and safety standards, for safety and proper use of the product, please pay attention to following points when using: Temperature changed and pressure will charge the piezo objective scanner. It will remain charged for a period of time disconnected from the controller, so the operator should pay attention when using it: Do not disassemble XD730.400 piezo objective scanner. Discharge XD730.
XD730.400 Piezo Objective Scanner User Manual 3. Product Overview 3.1 Product Introduction XD730.400 Piezo objective scanner has the following advantages: High performance piezo stack: XD730.400 is driven by high-performance piezo stack. It is fully insulated, so its performance and service life are far superior to conventional actuator. Insulating layer can effectively prevent piezo stack from being damaged by moisture. Stability of piezo stack could be ensured under extreme conditions.
3.3 Motion direction XD730.400 Lens adapter 4. Operating environment Operating temperature: -20~80℃ Environment free of dust, clean, and non-corrosive substances Relative humidity: <60% Recommended voltage between 0 and 120V for long-term and high-reliability operation 5. Installation and operation 5.1 Installation and connection Before installation, first check the safety, such as whether the cable is damaged or broken, and whether the power supply has grounding protection.
XD730.400 Piezo Objective Scanner User Manual Installation steps of XD730.400, as follows: 1. Screw the corresponding objective lens into the XD730.400 and tighten 2. Screw the lens into the adapter and tighten 3. Fix the installed piezo objective scanner and microscope connection section Fixed connection(M3) Lens adapter Note: During the installation process, please pay attention to handle, so as not to damage the XD730.400 piezo objective scanner or scratch and wear it. When connecting XD730.
5.2 Loading Connect the load according to the placement method described below, as shown in the figure below: Correct loading method Incorrect loading method When connecting the objective lens, pay attention that the quality of the objective lens does not exceed the maximum allowable load of XD730.400, and the load is not too long, otherwise it is easy to cause oscillation and damage XD730.400. 5.
XD730.400 Piezo Objective Scanner User Manual 3. After checking for no abnormalities, input voltage values according to requirements (keyboard or analog control). 4. It could work normally within the rated voltage range of piezo ceramic (0~120V, max not exceeding 150V); 5. Please set the piezo controller to zero after used. Please do not touch the product during the operation, avoid affecting the piezo scanner performance or even damage the piezo scanner. The resolution of piezo ceramic is not limited.
bruising, wetting, moisture, deformation, etc. Please check the parts on a case-by-case basis based on the supply contract and the packing list Whether there is obvious damage on the surface of the product Whether the product identification is clear and complete Whether the connector is loose, the connection line is broken or not, etc. If any of the above occurs, please make a detailed record and take a photo, and please contact us immediately.
XD730.400 Piezo Objective Scanner User Manual Loose connection Fastening connection Wiring is wrong Check the wiring is correct Reduced accuracy Vibration or The parameters are incorrect. Stop immediately, check the parameter settings inaccurate positioning at start-up Resonance operating frequency less than the resonant frequency If the user has problems that could not be solved. Please record the fault situation and contact with us.
8. Connector 8.1 Driving and Sensor cable Driving cable interface is 1-contact LEMO, model number is LEMO ERA.00.250.CTL, as shown below: Sensor cable interface is 4-contacts LEMO, model number is LEMO ERA.0S.304.
XD730.400 Piezo Objective Scanner User Manual 9.Customer Service If you have questions about the products you are currently using, please let us know the following information: Piezo stage model number and related number Controller model for this product Software driver version for this product Computer operating system for installing supporting software 10.Contact us Harbin Core Tomorrow Science & Technology Co., Ltd. Tel: +86-451-86268790 Email: info@coremorrow.com Website: www.coremorrow.
