GET STARTED Coredy E300 Mini Range Extender/Aessess Point/Router
Quick Installation Guide Preparing........................................................................... 1 Setup Process............................................................... 1 Web-Browser Method.................................................. 1 WPS - Method................................................................ 2 User Manual Overview................................................................................ 3 Using as a Extender................................................
Quick Installation Guide Below setup guide just for REPEATER Mode. If you need setup by AP and Router mode, please refer to User Manual. More details about troubleshoots please go to User Manual. Preparing: 1. Route works normal. 2. Switch the side button of repeater into “ON” & “Repeater” 3. Electrical Outlet close to router. Setup Process Web-Browser Method: 1. Plug it into an electrical outlet ( closest to your primary router/WiFi access point ) 2.
6. Enter your Router's/AP's WIFI password in the Password/WIFI Key/Security key column and click on "Apply" 7. In the next window, you'll see the reboot process with a Bar. When the Bar reaches 100%, (Leave the device for 1 minute to let it reboot itself). 8. Open the list of available networks again using your smartphone. Find out the New SSID "Coredy E300_EXT" and connect with it using the same password as of your primary router/AP. 9.
User Manual Overview The Coredy E300 WiFi Range Extender is a network device with multifunction, which can be using for increasing the distance of a WiFi network by boosting the existing WiFi signal and enhancing the overall signal quality over long distances. An extender repeats the signals from an existing WiFi router or access point. The Coredy E300 WiFi Range Extender also can be used as an Access Point or Router.
Before you install your extender, familiarize yourself with its LEDs, buttons, and port. Rear Panel Some computer required to type the password (pin number on the label) during the initial login. MAC:80:3F:5D:8A:7E:AA PIN:XXXXXXXX RESET WiF i AP/ PEPE MAC:8 ATE R PIN:960:3F:5D:9 3:6B:4 6125 45 6 WS-W SN:W N578R2 S150 REV 6270 Defau 029 .A lt URL:h IP:192 .168.1 User& ttp://ap.se 0.1 Passw tup ord:ad min Input: 10 50/60 0-240V~ Hz.0.
WLAN LED 1 – LED 3 Mode LEDs Description 1 2 3 Aeccess Point ON ON ON Wi-Fi fadio is operating Router ON ON ON Wi-Fi fadio is operating OFF No connection (This LED indicates the connection between the extender and the router or access point ) Bliking OFF Repeater ON ON ON Best connection ON ON OFF Good connection ON OFF OFF Poor connection WAN/LAN LED Lit amber. The E300 is starting. Blinking fast. The port is sending or receiving traffic. Off. No Ethernet cable is connected.
Using as a Extender When to Use Your Extender We recommend that you connect through the extender network only when the WiFi device is in a “dead zone” where connection from the existing network is poor or nonexistent. Data traffic routed through the extender is inherently slower than traffic routed directly from the network. How the Extender Works The extender works like a bridge between a WiFi router (or a WiFi access point) and a WiFi device outside the range of the WiFi router.
WiFi Range Extender Boosts the range of your existing WiFi and creates a stronger signal in hard to reach areas. Existing WiFi sometimes your router does not provide the WiFi coverage you need 1 Power on the Extender Turn the Power On/Off button to “On” and Mode Switch Button to “Repeater” on the side of the extender, plug the extender into an electrical outlet, place your extender in the same room as your WiFi router. Proximity to the WiFi router is required only during the initial setup process.
ON OFF Repeater WLAN 3 2 1 Power/WPS WLAN ON Router WAN/LAN OFF Access Point Power/WPS LAN oint sP r eate Rep es Acc WPS WAN/LAN LAN ter Rou 2 Connect to an Existing WiFi Network To extend the range of your WiFi network, you must connect the extender to your existing WiFi network. You can do this in one of two ways: Method 1. Connect with a web browser. Method 2. Connect with WPS. For more information, see Method 2: Connect with WPS. For more 11. Method 1: Connect with a web browser 1.
MAC:80:3F:5D:8A:7E:AA PIN:XXXXXXXX WLAN Power/WPS WAN/LAN LAN 2. Launch a web browser, enter http://192.168.10.1/ or http://ap.setup/ in the address field of the web browser, when prompted, enter admin for the user name and admin for the password, both in lowercase letters. 3. Click the Repeater in the Mode Wizard field. 4.
Note: Click the Refresh button if the wireless Network list couldn't loads completely or successfully. 5. In the Key (Network password) field, type the existing WiFi network password (also called the passphrase or security key) and click the Apply button, wait 1 minute to reboot the extender. 6. Find and connect to the new extended WiFi network on your computer or WiFi device. The extender creates a new extended WiFi network.
The location that you choose must be within the range of your existing WiFi router network. Use the WLAN LED 1 – LED 3 to help you choose a spot where the extender-to-router connection is optimal. 9. If only the WLAN LED 1 light amber , plug the extender into an outlet closer to the router and try again. Keep moving the extender to outlets closer to the router until the WLAN LED 1 , LED 2 and LED 3 light amber simultaneously.
1. Press the WPS button on the front panel of the extender. The WPS LED blinks. 2. Within two minutes, press the WPS button on your router or access point. When the extender connects to your existing WiFi network successful, the extender's new WiFi network name will change to “Coredy E300_EXT", and the WLAN LED1 LED 3 will light amber (check the WLAN LED Descriptions on Page 5), confirm it on your computer or WiFi device. If the extender could not connect to your existing WiFi network, try again.
Note: Place the extender in an elevated location and minimizing the number walls and ceilings between the router and your other devices. 6. Find and connect to the new extended WiFi network on your computer or WiFi device. The extender creates a new extended WiFi network. The extender’s new WiFi network name is “Coredy E300_EXT”, use the same WiFi password that you use for your WiFi router.
Using as a Access Point The Coredy E300 WiFi Range Extender also can be used as an Access Point, An access point receives data by wired Ethernet (such as hotel’s wired Ethernet), and converts to a 2.4Gig Hz wireless signal. It sends and receives wireless traffic to and from nearby wireless clients. WiFi AP coverts the wired network to a new WiFi network.
Cable Your AP The following image shows how to cable your AP: Internet WLAN Power/WPS WAN/LAN LAN LAN4 WAN Port LAN3 LAN2 LAN1 WAN LAN Port WAN Port Ethernet cable DSL or Cable 1. Power on the AP, turn the Power On/Off button to “On” and Mode Switch Button to “Access Point” on the side of the AP, plug the AP into an electrical outlet. 2. Connect the AP to your wired Ethernet port with the Ethernet cable came with your AP. 3.
4. Launch a web browser, enter http://192.168.10.1/ or http://ap.setup/ in the address field of the web browser, when prompted, enter admin for the user name and admin for the password, both in lowercase letters. 5. Click the AP in the Mode Wizard field. 6. Select the Security Type as WAP/WPA2 Mixed (recommended) and type the password of the WiFi Network in the Key field.
Using as a Router The Coredy E300 WiFi Range Extender also can be used as a Router. 1. Prepare your modem unplug your modem's power. If it has a battery backup, remove the battery. 2. Connect your modem, plug in your modem, Put the battery back in. Then cable the modem to the blue WAN port on the router. 3. Power on the router, turn the Power On/Off button to “On” and Mode Switch Button to “Router” on the side of the router, plug the router into an electrical outlet. 4.
We recommend that using a smart phone to connect with WiFi, the default WiFi network name is “Coredy E300”, type the password (PIN number) on the label of rear panel router if required. MAC:80:3F:5D:8A:7E:AA PIN:XXXXXXXX WLAN Power/WPS WAN/LAN LAN 5. Launch a web browser, enter http://192.168.10.1/ or http://ap.setup/ in the address field of the web browser, when prompted, enter admin for the user name and admin for the password, both in lowercase letters. 6. Click the Router in the Mode Wizard field.
If your ISP provides you the DSL details, Select “ ADSL Dial-up (PPPoE) “, enter the DSL user name and password, select the Security Type as “WPA/WPA2 Mixed” (recommended) and set the Wi-Fi Network password in “Key” field, click Apply button, the router will take 1 minute to reboot.
1) Place your router near the center of the area where your computers and other devices operate, and within line of sight to your wireless devices. 2) Make sure that the router is within reach of an AC power outlet and near Ethernet cables for wired computers. 3) Place the router in an elevated location, minimizing the number walls and ceilings between the router and your other devices.
Change the Extender Settings 1 To change the admin password 1. Launch a web browser. 2. Enter http://192.168.10.1/ or http://ap.setup/ in the address field of the browser login screen displays. 3. Enter admin for the user name and admin for the password, both in lowercase letters. The BASIC Home screen displays. 4. Select “Password” 5. Type your new user name and password twice. 6. Click the Apply button, Your changes are saved.
4. Select the Time Zone Settings. Password Time Zone Settings Save/Reload Settings Upgrade Firmware Management Reboot Device 5. Enter the Current Date and Current Time in field, click Apply. 3 Save/Reload your Extender setting You can use this feature to save your extender’s setting and reload it easy when you reset the router to factory setting or update the router firmware. 1. Launch a web browser. 2. Enter http://192.168.10.1/ or http://ap.
4 Update the Extender Firmware The extender firmware (routing software) is stored in flash memory. You might check if new firmware is available at www.coredytech.com and to update your product. 1. Launch a web browser. 2. Enter http://192.168.10.1/ or http://ap.setup/ in the address field of the browser login screen displays. 3. Enter admin for the user name and admin for the password, both in lowercase letters. The BASIC Home screen displays. 4.
5 Hide extender's wireless network You can hide the wireless network that which is hidden and does not display in your wireless client’s scanning list, other people cannot join the wireless network if they don’t know your wireless network SSID name exactly. For example, the Wi-Fi thief could not using your wireless network even they know your Wi-Fi Password. 1. Launch a web browser. 2. Enter http://192.168.10.1/ or http://ap.setup/ in the address field of the browser login screen displays. 3.
Wireless Settings Basic Settings Setup Wireless Basic Configuration Advanced Settings Wireless Advanced Configuration WPS Wi-Fi Protected Setup Schedule Basic Settings Broadcast SSID Disable SSID easytoremember Channel 2 Secutity Type Disable Wireless Schedule Back Apply Back to home page TROUBLESHOOTING Q1 How to reset E300 to factory settings? 1.
Q2 I am connected to Coredy E300_EXT and launched a browser, but I cannot log in the Setup Page/Web Management Page? Make sure that your computer is set up to use DHCP (most are). Relaunch the web browser and type http://192.168.10.1/ or http://ap.setup/ in the address field. Type your user name and password and click the LOG IN button. Reset the extender to factory setting.
Keep moving the extender to outlets closer to the router until the full WiFi signal on smart phone. 4. Plug the extender into an electrical outlet in an elevated location and minimizing the number walls and ceilings between the router and your other devices. Q4 The web browser setup guide keeps asking me for my network password (passphrase) or security key, and I am sure I have entered the correct password.
DNS for you, configure your computer manually with a DNS address, as explained in the documentation for your computer, if you don’t know how to manually the DNS, contact technical support at www.coredytech.com/support or Google “how to manually set DNS windows 7” . Q6 Cannot Join a WiFi Network and Receive an Error Message? To join a WiFi network, you must know its network name (also called the SSID) so that you can select it. If the network is secure, you must know the passphrase or key.
Sometimes extender’s WiFi connection between the WiFi router and the extender is poor. You can establish the best connection with a clear line of sight between the extender and the WiFi router. Make sure that no physical obstacles exist between the extender and the WiFi router, and try to move the extender closer to the WiFi router. Q7 Change the interference? wireless channel to reduce If you have adjacent access points, use different radio frequency channels to reduce interference.
Mini Range Extender/Aessess Point/Router MODEL: Coredy E300 Toll Free US: +1-800-999-8470 (English Service) Mon-Fri 10:00-19:00 (CST) Toll Free UK: +44-808-134-9909 (English Service) Mon-Fri 15:00-01:00 (GMT) E-Mail: support@coredytech.com Website: www.coredy.
