FCC This devious complies with part 16 of the FCC Rules.
I Introduction The Co recess 3114 is an Asymmetric Digital Subscriber Line {ADS} modem used for home connectivity to an ADS service provider network. The Co recess 3114 ADS modem receives adaptive data rates of up to bps downstream and transmits bps upstream. Key Features The Co recess 3114 ADS modem provides the following key features: Supports POTS and ADS simultaneously. Sends data, voice, and video aver high-speed ADS fines to connect to the Internet or corporate intranets.
rem I Unpacking the Box Check the shipping carton carefully fo ensure that the contents decline the items you ordered. IP Address NSA 10.002 (Default | 100.02 (Default) | 1000.2 (Default) Scorecards 3114 LAN | Subset Mask Nis 255.0.0.0 (Default) | 255.0.0.0 (Default | 255.0.0.0 (Default CPD Server N/A Enabled Enabled Enabled NAT N/A PANT PANT PANT N/A N/A ONS N/A (Automatically | Provided by ISP | (Automatically Assigned by ISP) Assigned by KP Nate: WA means it does not apply to the encapsulation.
Caution: You must power on the Co recess 3114 before powering on your FC. If you power on your PC fist, PC's 1P address may not be properly assigned. In this case, assign new [P address referring fo The Co recess 3114 supports both the POTS splutter and micro filter phone configurations. Before “Troubleshooting on page 17-18 of restart your PC. cabling the Co recess 3114, verify your configuration with your service provider. This section describes how to install the Co recess 3114 by using micro filter.
Click Next to start the installation of the drivers and connection to the ADS modem over the . 5. The wizard shows a verification panel and displays the choice you NET CARD). h Installing the Driver (USB Only) USB. (Figure 5) If you connect the Co recess 3114 to your PC using USE port, after connecting the cables to the Co recess 3114, install the software driver. S37 -) Ren IT gp, eso, mre 1. Tum on the PC connected with the Co recess 3114. i 2 man 2.
3. Two choices appear. Choose Include this location in the search and enter the CD-ROM drive letter. Insert the installation driver CD into the CD-ROM drive and click Next. Figure 2) 4. lf the path is correct, the system finds the driver and begins to automatically copy the driver files from the CD, (Figure 3) cE ote ye rose NEE figure 6. During the driver installation, the window for verifying the compatibility of the driver with XP may appear, Click Continue Anyway. (gore 4) 6.
! Configuring the TCP/IP 1. Click the Start button and select Settings 9 Network and Dial After you install the Co recess 3114 and the software driver, next is to configure the TCP/IP up Connections. (Figure 1 network protocol. Caution: When you configure the TC PAP, leave the default value of any other configuration t 3 is fot mentioned in the following description 2. Right-click the Local Area Connection icon at the windows and select Properties RL ERE menu. (Fig um 2) 1.
i Troubleshooting 1. Click the Start button and select Settings men. (Figure 1) NE are 1 you cannot connect fo ADS network, please check the status of the LED on the front pare], and then ensure the following: 2. Double click the Network @ icon at the window. Figure © 1. Check the LANCED ’ If the LAN LED goes off, ensure that the Theme cable is firmly connected both to the LAN 3.
RET © Click the Start button and select Run © The DOS-prompt appears. Input configure release and press [Enter] key. 1 Technical Specifications Hon , Standard + IEEE 802.30 100BaseTX : Ethernet Slim 107 ee + Corrector: CED cw Interface To Crete Multi-Tone) stream: Max 8hibps 4. Restart your PC + Upstream: Max Nimby + Connector. JR-11 tf new IF address is not assigned properly or you cannot solve the problem, ensure that the Co recess 3114 turns on and then restart your PC.
