Instruction Manual

OPERATION:
BRIGHT-SELECT SWITCH
Use LOW/OFF/HIGH switch to change between
low-level white light and high-level white light.
USB CHARGING
Both ports share 2.4 Amps of total output —
fully charge a single tablet or two smartphones.
SPECIFICATIONS
Electrical Ratings: 120VAC 60HZ 0.33A 39.6W
USB Ratings: 2.4A / 5V / 12W
LED Light Lumens: 503lm
LED Light Watts: 7.8W
LED Light Lumens/Watt: 64.5lm/W
LED Light CRI: 97
LED Light CCT: 3000K
SAFETY INSTRUCTIONS
Read and follow all safety instructions
• This product may represent a possible shock
or fire hazard if improperly installed. Products
should be installed in accordance with these
instructions, current electrical codes, and/or the
current National Electric Code (NEC).
FUNCIONAMIENTO:
INTERRUPTOR DE SELECCIÓN DE BRILLO
Use el interruptor LOW/OFF/HIGH para cambiar
entre luz blanca de baja intensidad y luz blanca
de alta intensidad.
CARGA USB
Ambos puertos comparten 2,4 amperios de
salida total: una carga completa de una tableta o
dos teléfonos inteligentes.
ESPECIFICACIONES
Especificaciones eléctricas: 120VAC 60HZ
0.33A 39.6W
Especificaciones USB: 2.4A / 5V / 12W
Lúmenes de la luz LED: 500lm
Vatios de la luz LED: 8W
Lúmenes/vatios de la luz LED: 64.5lm/W
IRC de la luz LED: 90
TCC de la luz LED: 3000K
INSTRUCCIONES DE SEGURIDAD
Lea y siga todas las instrucciones de seguridad
• Este producto puede representar la posibilidad de
descarga eléctrica o peligro de incendio si se instala
incorrectamente. Los productos deben instalarse de
acuerdo con estas instrucciones, los códigos eléctricos
vigentes o el Código Eléctrico Nacional (NEC) vigente.
• Consult a local licensed electrician or electrical
contractor if you are not sure about installing
the fixture yourself.
• Do not attempt to install the fixture while
plugged in.
• Injury to persons and damage to the fixture
and/or mounting surface may result if the
fixture is pulled from the surface. To reduce the
likelihood of such injury or damage, mount to a
surface that is mechanically sound.
• Never use an extension cord unless the plug can
be fully inserted. Do not alter the plug.
• Not to be used with a dimming circuit or any
other electronically switched control.
CARE AND MAINTENANCE
• Do not use paints, solvents, chemicals or harsh
abrasives on this light fixture.
• Clean only with a dry soft cloth.
• Do not use if there is any damage to the light or
power cord insulation. Inspect periodically.
FCC STATEMENT:
Suppliers Declaration of Conformity | Model #:
51766 | Jasco Products Co., 10 E. Memorial Rd.,
Oklahoma City, OK 73114, www.byjasco.com
This device complies with Part 15 of the FCC
rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
FCC NOTE: The manufacturer is not responsible
for any radio or TV interference caused by
unauthorized modifications to this equipment.
Such modifications could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment o and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the
equipment and receiver.
— Connect the equipment into an outlet on a
circuit dierent from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV
technician for help.
51766 EnSp Manual v1
12/21
Cordinate and the Cordinate logo
are registered trademarks owned
by Jasco Products Company LLC.
MADE IN CHINA
Distributed by Jasco Products Company
LLC, 10 E. Memorial Rd., Oklahoma City,
OK 73114
This product comes with a 3-year limited
warranty. Visit www.cordinateme.com for
warranty details.
Questions? Contact our U.S.-based Consumer
Care at 1-800-654-8483 between 7AM-8PM,
M-F, Central Time.
RISK OF ELECTRIC SHOCK
• DO NOT USE IN WET LOCATIONS.
• USE INDOORS ONLY.
• USE ONLY INSULATED STAPLES OR PLASTIC TIES TO SECURE
THE CORDS.
• ROUTE AND SECURE THE CORDS SO THAT THEY WILL NOT BE
PINCHED OR DAMAGED.
• NO SERVICEABLE PARTS.
• NON-REPLACEABLE LEDS.
• LED LIGHT OUTPUT IS STRONG ENOUGH TO INJURE HUMAN
EYES. PRECAUTIONS MUST BE TAKEN TO PREVENT LOOKING
DIRECTLY AT THE LEDS WITH UNAIDED EYES FOR MORE THAN
A FEW SECONDS.
RISK OF FIRE
• NOT INTENDED FOR ILLUMINATION OF AQUARIUMS.
• NOT INTENDED FOR USE ABOVE STOVES, COOK TOPS, SINKS
OR OTHER HEAT PRODUCING APPLIANCES, SUCH AS COFFEE
MAKERS, TOASTERS, OR TOASTER OVENS.
• NOT INTENDED FOR RECESSED INSTALLATION IN CEILINGS
OR SOFFITS.
• NOT INTENDED FOR SURFACE INSTALLATION INSIDE OR ON
TOP OF BUILT-IN FURNISHINGS SUCH AS KITCHEN CABINETS,
CHINA CABINETS, OR TROPHY CASES.
• DO NOT CONCEAL POWER SUPPLY CORD OR LINKING CORDS
INSIDE A WALL, CEILING, SOFFIT, KITCHEN CABINET, OR
SIMILAR PERMANENT STRUCTURE.
• DO NOT RUN THE POWER SUPPLY CORD OR LINKING CORDS
THROUGH HOLES IN WALLS, CEILINGS OR FLOORS.
WARNING
100%
recyclable
Separate
paper
from plastic
before
recycling
byjasco.com/recycle
paper made from 25%
post consumer waste
HERRAMIENTAS NECESARIAS:
• Lápiz
• Destornillador Phillips n.º 1
• Taladro eléctrico
• Gafas de seguridad
• Broca de 1/16” (maderas blandas),
broca de 3/32” (maderas duras)
INSTALACIÓN:
MONTAJE SOBRE UNA SUPERFICIE
Paso 1: Elija el lugar de montaje
Asegúrese de que el cable de alimentación de 1,5
m (5 ft) llegue hasta el tomacorriente de 120 VCA
más cercano. El lugar de montaje elegido debe ser
uno en interiores, seco y con capacidad de sosener
la lámpara.
Paso 2: Retire la placa de montaje
Retire la placa de montaje de la parte posterior
de la lámpara empujando con firmeza hacia el
cable de alimentación, tire para extraer.
Paso 3: Marque las ubicaciones de los tornillos
Sostenga la placa de montaje en el lugar de
montaje elegido. Con un lápiz, marque la
ubicación de cada tornillo.
Paso 4: Perfore
previamente los orificios
Perfore los orificios
piloto para los tornillos
guiándose por las marcas
con lápiz. Use una broca
de 1/16” (1,5 mm) para
maderas blandas y una
broca de 3/32” (2,4 mm)
si la madera es dura.
Paso 5: Instale la placa de
montaje
Sostenga la placa de
montaje en el lugar. Use
un destornillador Phillips
n. ° 1 y los tornillos provistos
para fijarlos en su lugar, no
apriete demasiado.
Paso 6: Monte la lámpara
Alinee los orificios tipo cerradura en la lámpara
con los postes en la placa de montaje. Deslice la
lámpara hasta que encaje en su lugar.
Paso 7: Conecte a la energía
nserte el cable de
alimentación de 1,5 m
(5 ft) en el tomacorriente
de 120 VCA más cercano.
COLOCACIÓN EN ESCRITORIO
Retire la placa de montaje y coloque la lámpara
en el escritorio o mesa con los soportes de
goma en contacto con la superficie. La
colocación ideal es en el borde trasero del
escritorio o contra una pared con el lente
orientado en el sentido opuesto a usted.