User manual

7
Conexi—n elŽctrica
Antes de enchufar el aparato, asegurarse de que la
tensi—n y la frecuencia indicadas en la tarjeta
matr’cula, correspondan a las de la instalaci—n
domŽstica. Se admite una oscilaci—n de 6% sobre la
tensi—n nominal.
Para el funcionamiento a tensiones distintas, habr‡
que utilizar un autotransformador de potencia
adecuada. Asegurarse de que la toma de corriente y
el enchufe sean compatibles entre s’ sin tener que
interponer reducciones ladrones o adaptadores
varios. Si fuera necesario, cambiar la toma de la
instalaci—n de la casa con una adapta.
Es indispensable conectar el aparato a una toma
de tierra eficaz.
Para ello el enchufe del cable de alimentaci—n est‡
dotado de un adecuado contacto. Si la toma de
corriente de la instalaci—n domŽstica no estuviera
conectada a tierra, conectar el aparato a una
instalaci—n de tierra, conforme a las leyes en vigor,
consultando para ello con un tŽcnico especializado.
El fabricante declina toda responsabilidad en el
caso que esta norma no sea respetada.
Este aparato es conforme a las siguientes
Directivas Comunitarias:
- 87/308 CEE del 2/6/87 relativa a la supresi—n de
interferencias radio.
- 73/23 CEE 19/02/73 (Baja tensi—n) y
modificaciones sucesivas;
- 89/336 CEE 03/05/89 (Compatibilidad
electromagnŽtica) y modificaciones sucesivas.
INSTALACIîN
Colocaci—n
Situar el aparato lejos de fuentes de calor, como:
radiadores, estufas, exposici—n directa a los rayos
del sol, etc.
Asegurarse de que en les partes posterior, superior
e inferior no haya ningœn obst‡culo que impida la
circulacidn del aire.
Para que el aparato rinda mejor, la distancia m’nima
entre la parte superior y el eventual mueble pŽnsil
de encima, deber’a ser por lo menos de 100 mm
(A).
La soluci—n preferible, de todos modos, seria la
ilustrada en la B (sin mueble).
Dos patas graduables, situadas en la base del
mueble, consienten rivelarlo a la perfecci—n.
Asegurarse de que la toma de corriente y el enchute
sean compatibles entre s’ sin tener que interponer
reducciones ladrones o adaptadores varios. Si fuera
necesario, cambiar la toma de la instalaci—n de la
casa con una adepta.
100 mm10 mm
10 mm
A
B
NP006
Atenci—n
Se debe poder desenchufar el aparato; por lo
tanto una vez efectuada la instalaci—n es
necesario que el enchufe no quede escondido
10
CONTENTS
Warnings 9
Use 11
Cleaning the interior 11
Operation 11
Temperature regulation 11
Fresh food refrigeration 11
Movable shelves 11
Positioning the door shelves 11
Hints 12
Hints for refrigeration 12
Maintenance 12
Periodic cleaning 12
Periods of no operation 12
Interior light 12
Defrosting 12
Customer service and spare parts 13
Technical information 13
Installation 14
Location 14
Electrical connection 14
Rear spacers 15
Changing the opening direction of the door 15
¥ Do not place carbonated or fizzy drinks in the
freezer as it creates pressure on the container,
which may cause it to explode, resulting in
damage to the appliance. Do not use a
mechanical device or any artificial means to
speed up the thawing process other than those
recommended by the manufacturer. Never use
metal objects for cleaning your appliance as it
may get damaged.
Installation
¥ During normal operation, the condenser and
compressor at the back of the appliance heat up
considerably. For safety reasons, minimum
ventilation must be as shown in the relevant
Figure.
Attention: keep ventilation openings clear of
obstruction.
¥ Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Important: if the supply cord is damaged, it must
be replaced by a special cord or assembly
available from the manufacturer or its service
agent.
¥ There are working parts in this product which
heat up. Always ensure that there is adequate
ventilation as a failure to do this will result in
component failure and possible food loss. See
installation instructions.
¥ Parts which heat up should not be exposed.
Wherever possible the back of the product should
be against a wall.
¥ If the appliance has been transported horizontally,
it is possible that the oil contained in the
compressor flows in the refrigerant circuit. It is
advisable to wait at least two hours before
connecting the appliance to allow the oil to flow
back in the compressor.
Environment Protection
This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The
appliance shall not be discarded together with
the urban refuse and rubbish. Avoid damaging
the cooling unit, especially at the rear near the
heat exchanger. Information on your local
disposal sites may be obtained from municipal
authorities. The materials used on this appliance
marked by the symbol are recicable.