EN User Manual WASHING MACHINE User Manual AW 710SD
CONTENTS CHAPTER-1: 4 BEFORE USING THE APPLIANCE • Correct Usage 6-7 • General warnings 8-9-10-11 • Safety warnings 12-13-14-15-16-17 • Packaging and Environment 18 • Savings Information 19 CHAPTER-2: OVERVIEW OF YOUR DEVICE • General Appearance 20-21 • Techincal Specifications 22 CHAPTER-3: INSTALLATION • Removing transportation safety screws 23-24-25 • Adjusting Adjustable Stays 26-27 • Electrical connection 28 • Water inlet hose connection 29-
CONTENTS 5 CHAPTER-5: PRELIMINARY PREPARATION FOR LAUNDERING • Separating laundries 38-39 • Putting laundries in the machine 40 • Adding detergent into machine 41 • Operating your machine 42-43-44 • Auxiliary functions 45-46-47-48-49-50 • Child lock 51 • Cancelling programme 52 • Finishing programme 53 CHAPTER-6: PROGRAM TABLE CHAPTER-7: MAINTENANCE AND CLEANING OF YOUR MACHINE • Warning 62 • Water inlet filters 63 • Pump filter 64-65 • Detergent drawer
CHAPTER -1: BEFORE USING THE APPLIANCE (CORRECT USAGE) • Definitely read the user’s manual. • Your machine is designed to be used domestically. Commercial use will cause your warranty to be cancelled. • Keep your pets away from your machine • Please check the packaging of your machine before installation, and the outer surface after the package is opened. Do not operate damaged machines or machines with opened package. • Have your machine installed only by authorized service.
CHAPTER -1: BEFORE USING THE APPLIANCE (CORRECT USAGE) • Use your machine only for laundries that have been specified as suitable for washing by the manufacturer. • Before operating the washing machine, remove the 4 transportation screws and rubber spacers from the back of the machine. If the screws are not removed, it may cause heavy vibration, noise and product malfunction, (voiding the guarantee).
CHAPTER -1: BEFORE USING THE APPLIANCE (GENERAL WARNINGS) 8 • The necessary ambient temperature for your machine’s ideal operation is 15-25°. • Frozen hoses can tear and explode. In regions where temperature is below zero, ambient temperature might endanger the safe operation of electronic card. • Please ensure that the clothes you will place in your machine do not contain any foreign substances (nail, needle, coins, lighter, matches, clip etc.) in their pockets.
CHAPTER -1: BEFORE USING THE APPLIANCE (GENERAL WARNINGS) • As detergent or softener exposed to air for a long time may cause residues, put your detergent or softener in the detergent drawer at the beginning of every washing. • It is advised that you unplug your machine and close the water inlet tap if you will not use your machine for a long time. Also, leaving the door of your machine will prevent the formation of bad odors due to humidity.
CHAPTER -1: BEFORE USING THE APPLIANCE (GENERAL WARNINGS) • Never open the detergent compartment when the appliance is running. • In case of any breakdown, unplug the appliance first and then turn the tap off. Do not attempt to repair by yourself, always contact for authorized service advice. • The amount of laundry you put in your washing machine should not exceed the maximum amount indicated. • Never force the door to open when the machine is running.
CHAPTER -1: BEFORE USING THE APPLIANCE (GENERAL WARNINGS) • Please adhere to detergent/fabric conditioner manufacturers’ advice regarding the use of fabric conditioner or similar products in your machine. • Set up your machine in a place where its door can be completely opened. (Do not set up your machine in places where its door cannot be fully opened.) • Set up your machine at locations that can be fully ventilated and could have constant air circulation.
CHAPTER -1: BEFORE USING THE APPLIANCE (SAFETY WARNINGS) You must read these warnings. You can thus protect yourself and your beloved ones against fatal injuries and risks. DANGER OF GETTING BURNT! Do not touch discharging hose and water during discharging as the appliance may reach high temperatures when running.
CHAPTER -1: BEFORE USING THE APPLIANCE (SAFETY WARNINGS) DEATH RISK DUE TO ELECTRICAL CURRENT! • Do not use multiple receptacles or extension cord. • Do not plug in damaged or torn plugs. • Never pull the cable when unplugging – always grip the plug itself. • Do not plug-in or out the plug from the receptacle with wet hands to prevent electrocution! • Never touch the machine with wet hands or feet. • Call the nearest authorized service for a replacement if the power cord malfunctions.
CHAPTER -1: BEFORE USING THE APPLIANCE (SAFETY WARNINGS) Flooding risk! • Check whether the water runs fast or not before placing the discharge hose on the sink. • Take necessary measures to prevent the slipping of your hose. • The backfiring force of a hose that is not placed appropriately can displace the hose. Prevent the stopper inside your sink from blocking the sink hole.
CHAPTER -1: BEFORE USING THE APPLIANCE (SAFETY WARNINGS) Danger of Fire! • Do not keep inflammable liquids near your machine.. • The sulphure content of paint removers might cause corrosion. For this reason, never use paint-removing materials in your machine. • Never use products that contain solvent material (like washing gas) in your machine. • Remove all the objects in the pockets of your laundries (needle, paperclip, lighter, matches etc.) when placing them your machine.
CHAPTER -1: BEFORE USING THE APPLIANCE (SAFETY WARNINGS) Fall and injury hazard! • Do not climb on your machine. The upper table of your machine may break and you might get injured. • Tidy the hose, cable and packaging of your machine during installation. You might trip over and fall. • Do not turn your machine upside down, or on its side. • Do not lift your machine by holding it from extruding parts (detergent drawer, door). These parts might break and cause you to get injured.
CHAPTER -1: BEFORE USING THE APPLIANCE (SAFETY WARNINGS) 17 Child safety! • Do not leave children unattended near the machine. Children might lock themselves up into the machine and death risk might occur. • Door glass and surface might be extremely hot while your machine operates. Thus, especially touching the machine might give damage to the skins of children. • Keep packaging material away from children.
CHAPTER -1: BEFORE USING THE APPLIANCE PACKAGING AND ENVIRONMENT Removal of packaging materials Packaging materials protect your machine from any damage that might occur during transportation. Packaging materials are environment friendly as they are recyclable. Recycling material provides both raw material savings and decreases waste production. Disposal of old machine Electrical or electronical old devices might still contain salvagable parts.
CHAPTER -1: BEFORE USING THE APPLIANCE SAVINGS INFORMATION Some important information to get more efficiency out of your machine: • The amount of laundry you put in your washing machine should not exceed the maximum amount indicated. By this way, your machine shall run in saving mode. • Not using the pre-wash feature for little and normal-dirty laundry shall save electricity and water.
CHAPTER -2: OVERVIEW OF YOUR DEVICE GENERAL APPEARANCE Electronic display Programme knob Upper Tray Detergent drawer Container Cover of pump filter 20
CHAPTER -2: OVERVIEW OF YOUR DEVICE GENERAL APPEARANCE Transportation Safety Screw Water Inlet Valve Discharging Hose Power Cable Transportation Safety Screw Transportation Safety Screw Transportation Safety Screw 21
CHAPTER -2: OVERVIEW OF YOUR DEVICE TECHNICAL SPECIFICATIONS Operating voltage / frequency (V/Hz) (220-240) V~/50Hz Total current (A) 10 Water pressure Maximum: 1 Mpa Minimum : 0.
CHAPTER -3: INSTALLATION REMOVING TRANSPORTATION SAFETY SCREWS Before operating the washing machine, remove the 4 transportation screws and rubber spacers from the back of the machine. If the screws are not removed, it may cause heavy vibration, noise and product malfunction, (voiding the guarantee). For this reason, transportation safety screws shall be loosened by being rotated in counter-clockwise using an appropriate wrench.
CHAPTER -3: INSTALLATION (REMOVING TRANSPORTATION SAFETY SCREWS) Transportation screws shall be removed by pulling out. Fit the plastic transportation screw taps delivered in accessories bag to the palces where transportation screws have been removed. The transportation safety screws should be stored to be used in case of transportation. NOTE: You should absolutely remove the transportation screws of your machine before the first usage.
CHAPTER -3: INSTALLATION (ADJUSTING ADJUSTABLE STAYS) 25 Adjusting Adjustable Stays • Do not install your machine on a carpet or such grounds that would prevent the ventilation of its base. • To ensure silent and vibration-free operation of your machine, it should be deployed on a non-sliding and firm ground. • You can adjust the balance of your machine through the stays. • Loosen the plastic adjustment nut.
CHAPTER -3: INSTALLATION (ADJUSTING ADJUSTABLE STAYS) • Adjust the stays upward and downward by rotating them. • After maintaining the balance, compress the plastic adjustment nut upward again.
CHAPTER -3: INSTALLATION (ADJUSTING ADJUSTABLE STAYS) • Never put cardboard, wood or suchlike materials under your machine if you are intending to stabilize the distortions on the ground. • When cleaning the ground, on which your machine rests, be careful not to disorder stays stabilization.
CHAPTER -3: INSTALLATION (ELECTRICAL CONNECTION) • Your washing machine is set to 220-240V and 50Hz. • The mains cord of your washing machine is equipped with a specific earthed plug. This plug should always be inserted to a earthed socket of 10 amps. The current value of the fuse should be 10 amps. Fuse current value of the power line connected to this plug should also be 10 amperes. If you don’t have such a receptacle and fuse confirming with this, please have it done by a qualified electrician.
CHAPTER -3: INSTALLATION (WATER INLET HOSE CONNECTION) 29 • To eliminate water leakages in points of contact, 1 or 2 nuts are provided in the hose package (applicable for machines with double water inlets). Fit these nuts to the ends of new water inlet hoses on the side of faucet. • Mount new water inlet hoses to a ¾ ˝, threaded faucet.
CHAPTER -3: INSTALLATION (WATER INLET HOSE CONNECTION) • Ensure that the new water inlet hoses are not bent, broken, crushed and resized. • If your machine has double hot water inlets, the temperature of hot water inlet should be maximum 70°C. Note: Use only the new water inlet hose coming with your machine while making Water inlet hose connections of your machine. Never use old, used or damaged water inlet hoses.
CHAPTER -3: INSTALLATION (WATER DISCHARGE CONNECTION) 31 • The end of water discharge hose can be fitted to a specific apparatus directly attached to dirty water discharge hole or outlet joint of the basin elbow. • Never attempt to extend the water discharge hose by jointing. • Do not put discharging hose of your machine in a vessel, bucket or sink. • Make sure that the water discharge hose does not bend, buckle, be crushed or extended.
CHAPTER -4: INTRODUCTION OF CONTROL PANEL 32 Programme knob Elektronic Display and Additional Functions Detergent drawer
CHAPTER -4: INTRODUCTION OF CONTROL PANEL (DETERGENT DRAWER) 33 You can use the liquid level determination plate when you want to wash your laundry with liquid detergent. You can use your liquid detergents in all programs without prewashing. Place the liquid detergent aparatus in the second compartment (which is available inside the machine) of the detergent drawer (*) and set the detergent amount. (Use the recommended amount of liquid detergent by detergent producers).
CHAPTER -4: INTRODUCTION OF CONTROL PANEL (DETERGENT DRAWER) 34 SECTIONS Main wash detergent compartment: In this compartment, only materials like detergent (liquid or powder), lime preventer and such can be used. You can find the liquid detergent aparatus inside your machine at first installation. (*) Fabric conditioner, starch, detergent compartment: You can use softener for your laundry (recommended amount and type by the producer is recommended).
CHAPTER -4: INTRODUCTION OF CONTROL PANEL (PROGRAM KNOB) • You can select the programme you want to wash your laundry in through programme knob. • You may set the programme selection operation by rotating the programme knob in both directions. • Ensure that the programme knob is exactly on the programme you want to select.
CHAPTER -4: INTRODUCTION OF CONTROL PANEL (ELECTRONIC DISPLAY) Electronic Display Wash level display Digital Display Function display Auxiliary function symbol Start/Pause button Auxiliary function button Delayed start auxiliary function Rpm speed adjustment button Water Temperature Adjustment Button 36
CHAPTER -4: INTRODUCTION OF CONTROL PANEL (ELECTRONIC DISPLAY) On the electronic display, you may view washing water temperature, spinning revolution speed of your machine, when your machine will finish washing, the auxiliary functions you have selected and at what stage the programme you have chosen is ( prewash/wash, rinsing, spinning).
CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING (SEPARATING LAUNDRIES) 38 • Your laundry has product labels on them that specifiy their specifications. Wash or dry your laundry according to the specifciations on the product label. DGVDSHSFHS DGVDSHSFHS DGVDSHSFHS DGVDSHSFHS • Separate your laundries according to their types (cotton, synthetic, sensitive, wool etc.), their temperatures (cold, 30°, 40°, 60°, 90°) and degree of contamination (slightly stained, stained, highly stained).
CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING (SEPARATING LAUNDRIES) Whitening available No whitening Normal washing Ironing temperature is maximum 150°C Ironing temperature is maximum 200°C No ironing Dry cleaning available No dry cleaning Leave on a flat place Hang when wet Dry by hanging Drying by twirling is not allowed F P A Dry cleaning in gas oil, pure alcohol and R113 is allowed Perchloroethylene R11, R13, Petroleum Perchlorinetyhlene R11, R113, Gas oil 39
CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING (PUTTING LAUNDRIES IN THE MACHINE) 40 • Open the door of your machine. • Spread your laundries in your machine. NOTE: Note: Maximum loading capacity may vary based on the laundry type you will wash, degree of contamination and the programme you have chosen. Do not exceed maximum dry loading capacity indicated in the programme table for washing programmes. You can take the following table of weights as an example.
CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING (ADDING DETERGENT INTO MACHINE) 41 The amount of detergent you will put in your machine will depend on the following criteria: • Your detergent utilization will be based on the degree of contamination of your laundries. Do not prewash your less stained laundries and put your slight amount of detergent in the 2nd compartment of the detergent drawer.
CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING (OPERATING YOUR MACHINE) • Plug your machine in. • Open the water faucet. • Open the machine door. • Spread your laundries in your machine. • Push the door of your machine until hearing the locking sound to close it. Selecting programme Select the convenient programme for your laundries on the programme table.
CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING (OPERATING YOUR MACHINE) 43 AUXILIARY FUNCTIONS Before starting the programme, you can optionally select an auxiliary function. • Press on the button of auxiliary function you would like to select. Temperature Spin Speed Delay Timer Auxiliary Function Selection Start/Pause • If auxiliary function symbol on electronic display flashes continuously, the auxiliary function you have selected will be activated.
CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING (OPERATING YOUR MACHINE) HALF-LOAD DETECTION SYSTEM Your machine features a half-load detection system. In case yuo put approximately half or less amount of launderies of maximum laundry capacity in your machine, your machine will run so as to save washing time, water consumption and energy in some programmes.When the halfload function is active, the machine can complete the programme you have set in a shorter time.
CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING AUXILIARY FUNCTIONS 45 1- Temperature selection You can select the washing water temperature with the washing water temperature adjustment button. Whenever you select a new programme, the maximum washing water temperature is shown on the washing water temperature display. You can gradually decrease the washing water temperature between the maximum temperature and cold washing (--) by pressing washing water temperature adjustment button.
CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING AUXILIARY FUNCTIONS 2- Spin speed selection 46 Spin Speed You can set the spin revolution for your laundries via revolution speed setting button. When you select a new programme, the maximum spin revolution speed of the programme you have selected will be viewed on the display of revolution speed.
CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING AUXILIARY FUNCTIONS 47 3- Delay timer By using this auxiliary function, you can set the time when your machine start washing. This time can vary from an hour to 23 hours. To use auxiliary function of delay timer: Temperature Spin Speed Delay Timer Auxiliary Function Selection Delay Timer - Press time delay button once. - Expression of “1 h” will appear on the display. Symbol will flash on electronic display.
CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING AUXILIARY FUNCTIONS 48 If you have skipped the time delay you want to set, you can go back to the time desired by keeping pressed on time delay button. If you want to cancel the time delay, you are required to press the time delay button once. symbol will no longer flash on electronic display. To run time delay function, your machine is required to be operated by pressing on Start/Pause button.
CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING AUXILIARY FUNCTIONS 49 6- Rapid wash(*) This auxiliary function will enable the washing duration of your laundries that are not very dirty to be shortened.
CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING AUXILIARY FUNCTIONS 50 8- Extra Rinse(*) You can make additional rinse operation on your laundry by using this additional function. You may make the programme active by pressing the extra rinsing auxiliary function button when the led light of the symbol turns on.
CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING (CHILD LOCK) To avoid programme flow from being affected if programme buttons are pressed or programme button is turned when performing washing operation in your machine, child lock is available. Child lock will be activated in case pressed on both auxiliary functions 3 and 4 at the same time for more than 3 seconds.
CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING (CANCELLING PROGRAMME) If you want to cancel any programme running: 1- Switch the programme knob to “CANCEL” position. 2- Your machine will stop the washing operation and the programme will be cancelled. 3- To get rid of the water accumulated in the machine switch the programme knob to any programme. 4- Your machine will perform the necessary discharge operation and cancel the programme. 5- You can run your machine by selecting a new programme.
CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING FINISHING PROGRAMME Your machine will stop by itself as soon as the programme you have selected finishes. - The expression of “END” will flash on the electronic display. Temperature Spin Speed Delay Timer Selection Auxiliary function Start/Pause - You can open the machine’s door and remove the laundry. - Leave the door of your machine open to allow the inner part of your machine to dry after removing your laundries.
CHAPTER -6: PROGRAM TABLE 54 COTTON 90° Washing temperature (°C) 90° Maximum dry laundry amount (kg) 7,0 Detergent compartment 2 Programme duration (Min.) 200 Very dirty, cotton and flax textiles. Laundry type / Descriptions (Underwears, linen, tablecloth, towel (maximum 3,5 kg), bedclothes, etc. Pre-Wash Cotton Washing temperature (°C) 60° Maximum dry laundry amount (kg) 7,0 Detergent compartment 1&2 Programme duration 165 Laundry type / Descriptions Dirty cotton and flax textiles.
CHAPTER -6: PROGRAM TABLE COTTON ECO 55 60 C° Washing temperature (°C) 60° Maximum dry laundry amount (kg) 7,0 Detergent compartment 2 Programme duration (Min.) Laundry type / Descriptions 205 COTTON Dirty cotton and flax textiles. (Underwears, linen, tablecloth, towel (maximum 3,5 kg), bedclothes, etc. 40 C° Washing temperature (°C) 40° Maximum dry laundry 7,0 amount (kg) Detergent compartment 2 Programme duration (Min.) 195 Laundry type / Descriptions Dirty cotton and flax textiles.
CHAPTER -6: PROGRAM TABLE 56 ECO 20° Washing temperature (°C) 20° Maximum dry laundry amount (kg) 3,5 Detergent compartment 2 Programme duration (Min.) 98 Laundry type / Descriptions Less dirty, cotton and linen textiles. (Underwear, bedsheet, tablecloth, towel (max. 2 kg) bedcloth, etc. EASY CARE Washing temperature (°C) 40° Maximum dry laundry amount (kg) 3,5 Detergent compartment 2 Programme duration (Min.) 91 Very dirty or synthetic-mixed textiles.
CHAPTER -6: PROGRAM TABLE 57 WOOL Washing temperature (°C) 30° Maximum dry laundry amount (kg) 2,5 Detergent compartment 2 Programme duration 49 Woollen laundries with machine Laundry type / Descriptions wash labels.
CHAPTER -6: PROGRAM TABLE 58 SPINNING Washing temperature (°C) Maximum dry laundry amount (kg) 7,0 Detergent compartment - Programme duration 17 If you want to additionally wring your upon completion of washing Laundry type / Descriptions laundries operation, you may use this programme for any kind of laundries.
CHAPTER -6: PROGRAM TABLE SPORTS WEAR Washing temperature (°C) 30° Maximum dry laundry amount (kg) 3,5 Detergent compartment 2 Programme duration 79 Laundry type / Descriptions Sportswear. MIXED Washing temperature (°C) 30° Maximum dry laundry amount (kg) 3,5 Detergent compartment 2 Programme duration 85 Laundry type / Descrip- Dirty cotton, synthetics, colour and flax textiles can be washed together.
CHAPTER -6: PROGRAM TABLE 60 BLOUSES / SHIRTS Washing temperature (°C) 60° Maximum dry laundry amount (kg) 3,5 Detergent compartment 2 Programme duration 110 Dirty cotton, synthetic and syntheticLaundry type / Descriptions mixed shirts and blouses can be washed together. DAILY 60 min.
CHAPTER -6: PROGRAM TABLE 61 RAPID 15 min. Washing temperature (°C) 30° Maximum dry laundry amount (kg) 2,0 Detergent compartment 2 Programme duration 15 Laundry type / Descriptions You can wash your slightly stained, cotton, colured and flax textile within only 15 minutes. NOTE: As the washing period is short, less amount of detergent is required to be used compared to other programmes. The programme period will increase if your machine detects instable loading.
CHAPTER -7: MAINTENANCE AND CLEANING OF YOUR MACHINE (WARNING) Unplug your machine before starting the maintenance and cleaning of your machine. Turn the tap water off before starting the maintenance cand cleaning of your machine. CAUTION: Your machine’s parts might be damaged if cleaners with solvent agents are used. Do not use cleaning materials with solvent agents.
CHAPTER -7: MAINTENANCE AND CLEANING OF YOUR MACHINE (WATER INLET FILTERS) 63 Filters to avoid dirt and foreign substances in the water from penetrating into the machine are available both on the side of faucet and on the ends of water valves along the water inlet hose of your machine. If your machine cannot intake sufficient amount of water despite water faucet being open, these filters should be cleaned. (It is recommended that you clean your pump filter once in 2 months.
CHAPTER -7: MAINTENANCE AND CLEANING OF YOUR MACHINE (PUMP FILTER) 64 A filter system which avoids threads remaining from your laundries and tiny materials from entering into the pump during water discharging operation carried out by your machine after completing washing so prolonging the lifecycle of your pump is available. It is recommended that you clean your pump filter once in 2 months.
CHAPTER -7: MAINTENANCE AND CLEANING OF YOUR MACHINE (PUMP FILTER) • Clean the foreign materials in the filter with a brush. • After cleaning the filter, fit the filter cover and tighten it by rotating it in clockwise direction. • While closing the pump cover, ensure that the parts on the inner side of the cover to match the holes on the front panel side. • You can reattach the pump cover in the reverse order that you removed it. WARNING! As water in the pump may be hot, wait until it cools down.
CHAPTER -7: MAINTENANCE AND CLEANING OF YOUR MACHINE (DETERGENT DRAWER) Your detergents may deposit residue in detergent drawer and housing of detergent drawer over time. To clean the residue formed, disassemble the detergent drawer in particular periods. It is recommended that you clean your pump filter every 2 months.
CHAPTER -8: FLUSH STOPPER / BODY / DRUM 67 Flush stopper Disassemble the detergent drawer. Disassemble the flush stopper and clean the softener residues completely. Refit the flush stopper after cleaning it. Check whether it has settled properly. Body Clean the outer body of your machine with warm water and a non-inflammable cleaning agent that will not abrade the body of your machine. After rinsing with some water, dry it using a soft and dry cloth.
CHAPTER -9: TROUBLESHOOTING 68 All repairing operations required for your machine should be carried out by our authorised service. If your machine requires a repair or if you cannot remove the fault by the help of the information provided as follows: • • Unplug your machine. Turn the water faucet off. FAULT Your machine does not start. Your machine does not intake water. POSSIBLE CAUSE TROUBLESHOOTING It is not plugged. Fuse blown. Plug it. Replace the fuses. Electricity cut-off.
CHAPTER -9: TROUBLESHOOTING FAULT Your machine does not discharge water. Your machine vibrates. POSSIBLE CAUSE 69 TROUBLESHOOTING Discharging hose clogged or twisted. Check the discharging hose, then either clean or untwist. Pump filter clogged. Clean the pump filter. (*) Laundry settled in the machine unevenly. Spread your laundry in the machine evenly. The feet of your machine have not been adjusted. Adjust the feet on your machine.
CHAPTER -9: TROUBLESHOOTING FAULT Excessive foam is formed in the detergent drawer. Unsatisfactory washing result. POSSIBLE CAUSE Excessive amount of detergent used. 70 TROUBLESHOOTING Press on Start/Pause button To eliminate foam formation, mix a spoon of softener with half litres of water, and pour the mixture in the detergent drawer. After 5-10 minutes, press on Start/ Pause button again. In your next washing operation, Adjust the detergent dose accordingly. Wrong detergent used.
CHAPTER -9: TROUBLESHOOTING FAULT POSSIBLE CAUSE 71 TROUBLESHOOTING Water being hard. ( Contaminated, lime water etc.) Adjust the amount of detergent based on the instruction of detergent manufacturer. Laundries distributed in your machine nonhomogenously. Spread your laundries in the machine properly and homogeneously. As soon as the machine is loaded with water, water discharges. The end of water discharging hose is too low for the machine. Set the water discharging hose on appropriate height.
CHAPTER -9: TROUBLESHOOTING FAULT Spinning operation is not performed or runs late. POSSIBLE CAUSE No fault. Unbalanced load control system has been activated. 72 TROUBLESHOOTING Unbalanced load control system will try to spread your laundries homogeneously. Wringling operation will begin after your laundry is spread. Place the laundry in the machine in a balanced fashion the next time.
CHAPTER -10: AUTOMATIC FAULT WARNINGS AND WHAT TO BE DONE 73 Your machine is equipped with the systems which are capable of both taking necessary precautions and warning you in case of any breakdown by means of continuous self-checking during washing operations. TROUBLE CODE POSSIBLE FAULT WHAT TO DO E01 The door of your machine is left open. Close the machine door. If your machine persists to indicate fault, turn off your machine, unplug it and contact the nearest authorised service immediately.
CHAPTER -11: PRACTICAL INFORMATION Alcoholic drinks: Spotted area should initially be washed using cold water, and then be wiped with glycerine and water and rinsed with vinegar-mixed water. Shoe shine: Spot should be rubbed out gently without damaging the cloth and be scrubbed and rinsed with detergent. If not removed, it should be scrubbed using the mixture obtained by adding 1 scale of alcohol (96˚) into 2 scales of water, and then be washed with warm water.
CHAPTER -11: PRACTICAL INFORMATION Tomato paste: After rubbing out the dried substances without damaging your laundry, submerge it in water for 30 minutes, and then scrub and wash it with detergent. Bouillon-Egg: Remove dried spot residues on your laundry, and then wipe it with a sponge or soft cloth submerged in cold water previously. Scrub with detergent, wash with diluted bleacher. Grease and oil stains: Firstly, wie the residues. Scrub the spot with detergent and wash it with warm soapy water.
CHAPTER -11: PRACTICAL INFORMATION Fruit: Stretch the spotted area of your laundry throughout the opening of a vessel, and pour cold water on it. Do not pour hot water on the spot. Wipe with cold water and apply glycerine. Allow 1-2 hours, wipe with a few drops of white vinegar, and rinse it. Grass stain: Wipe the stained part with detergent. If the type of your cloth permits bleacher using, wash with bleacher. Wipe your woollen laundries with alcohol.
CHAPTER -11: PRACTICAL INFORMATION Blood stain: Submerge your laundries in cold water for 30 minutes. If the stain is not removed, then submerge in a mixture of water and ammoniac (3 spoons of ammoniac in 4 litres of water) for 30 minutes. Crema, ice cream and milk: Submerge your laundries in cold water and scrub the spotted area with detergent. If the spot is not removed, apply bleacher to the extent suitable for your laundries. (Do not use bleacher for colour laundries.
DESCRIBING ENERGY LABEL AND SAVING ENERGY Model 78 Brand Energy Class Energy Consumption Noise Value While Washing Noise Value While Spinning Spinning Performance Class Dry Laundry Capacity Annual Water Consumption
DESCRIBING ENERGY LABEL AND SAVING ENERGY Energy and water consumption may vary based on water pressure, water hardness, water temperature, ambient temperature, laundry amount, additional function selection, voltage fluctuations.
DISPOSAL OF YOUR OLD MACHINE This symbol on the product or package implies that the product should not be treated as domestic waste. Instead, it should be delivered to applicable waste collection places recycling electrical and electronic equipment. You will contribute to avoid potential negative results regarding environment and human health, which will arise due to wrong waste procedure for the product by ensuring that this product is annihilated properly.
