CX-CT6A Computer Transmitter INSTRUCTION MANUAL 6 channel Radio Control System Digital Propotional Radio Control System www.copterx.com Copyright © 2008 KY MODEL Company Limited.
CX-CT6A Computer Transmitter MENU Table of content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CX-CT6A Computer Transmitter 1. Introduction Thank you for choosing 2.4G radio remote control digital products. If this is your first time to use this type of products, please read this manual carefully and strictly follow the instruction. You could refer to the manual if you have any problems during the operation. Please keep the manual well because you may have to use it again. 2. Services If you have any problems during the operation process, please refer to the manual.
CX-CT6A Computer Transmitter 3. Special Symbols Please pay attention to the following symbols when they appear on the manual. Danger : If the item is not operated by following the instructions, serious injuries, even mortal danger, may be resulted. Warning : If the item is not operated by following the instructions, serious injuries, even mortal danger, may be resulted. the item is not operated by following the instructions, minor Attention : Ifinjuries may be resulted. Prohibition Mandatory 4.
CX-CT6A Computer Transmitter 5. Battery Charging Notes If you use a Ni-Cd or Ni-MH rechargeable battery, please check before the flying. If there is a lack of electricity, accident may be resulted because of inadequate power or out of control. Therefore, please charge the battery immediately when the power is low. If you recharge a Ni-Cd or Ni-MH battery, please use our company dedicated charger. If the electrical current is too large, it may lead to overheat and fire accident.
CX-CT6A Computer Transmitter 6. Transmitter Parameters *Channels: 6 *Charger port: Yes *Frequency band: 2.4GHz *Simulator port: PS-2 *Power resource: 1.
CX-CT6A Computer Transmitter 8. Respective Part of the Transmitter Antenna Handle HOV.
CX-CT6A Computer Transmitter 9.
CX-CT6A Computer Transmitter 10. 2.4G Operation Notes This is a 2.4G item with automatic address code. Digital transmission mode is used so outside interference can be prevented. 10.01 Matching (code) If you are going to match the receiver with other transmitter, please follow the following steps: 1. Install the battery in the 2.4G transmitter and shut it down. 2. Insert the matching lines to the channel Bat port of the receiver. (Figure 1) 3. Connect the receiver battery to any one of the channel ports.
CX-CT6A Computer Transmitter 10.02 Boot 1. Connect every part. 2. Switch on the power supply. 3. Connect the power supply. 4. Receive LED light solid. 5. Ready for use. Boot Tx power ON Rx power ON 10.03 Shut down 1. Cut off the receiver power supply. 2. Cut off the transmitter power supply.
CX-CT6A Computer Transmitter 11. Computer Hardware Connection Steps A programming line is included in this transmitter. You may use it to set up the program as you like. 1. Install the battery to the transmitter and switch on the power. 2. Plug in the programming line to the transmitter port. 3. Plug in the other head of the programming line to PC. 4. Launch the software program T6CONFIG.EXE. 5. Click the setting buttons and select programming line port. 6.
CX-CT6A Computer Transmitter 12. Computer Software Installation With new computer programmable model design, all functions of transmitter can be set up through computer. 12.01 PC Software Download You can download from our website: www.copterx.com 12.02 PC Software Installation 1. Install driver software: PL-2303 Driver Installer.exe 2. Install application software: t6config.exe 3. Restart computer 4. Installation completed 12.03 PC Software Application 1.
CX-CT6A Computer Transmitter 13. Transmitter Function Notes (Heli) Connect the transmitter programming line with the PC. Switch on the transmitter and start the application software. If you choose HELI90, HELI120 or HELI140, the following interface will appear: Channel Output Display System Function Option System Function Setting Switch Program Setting 13.
CX-CT6A Computer Transmitter If you want to save your settings, click “SAVE” on the main interface. You can then give it a name and click “SAVE” to save. If you want to open your settings, click “OPEN” on the main interface. Select the file and click “OPEN” to open. 13.02 System Function Settings To adjust the movement of servo to a suitable angle for a better control, click “EndPoint”. Each servo can be adjusted individually. It is divided into left half part and right half part.
CX-CT6A Computer Transmitter To use double ratio control of CH1/CH2/CH4 channel, click “DR”. It gives you the best control of the model. It is also a great help for beginners. CH1/CH2/CH4 channels can be adjusted individually. Adjusted value is from 0% to 100%. You may enter the numbers directly from the keyboard. This function will only be effective when the “DR” button is switched on. Click “OK” when the adjustment is finished. To adjust the control mode according to one’s own habit, click “Stick”.
CX-CT6A Computer Transmitter To adjust swashplate of CCPM function helicopter for a better control, click “Swash Afr”. CH1/CH2/CH4 channels can be adjusted individually. Adjusted value is from 0% to 100%. You may enter the numbers directly from the keyboard. Click “OK” when the adjustment is finished. To use the programmable mixed control function, click “MIX.”. This system offers three individual mixed control function (MIX1/MIX2/MIX3).
CX-CT6A Computer Transmitter 14. Content NO: Model Quantity Remarks 1 6-Channel 2.4G Transmitter (CX-CT6A) 1 2 6-Channel 2.
www.copterx.com Copyright © 2008 KY MODEL Company Limited.
