TDS

ManualsBrandsCOPPER FORCE ManualsPaint5 gal. #MQ3-04 Quiet On The Set Eggshell Enamel Virucidal and Antibacterial Interior Paint & Primer

TECHNICAL DATA SHEETTECHNICAL DATA SHEET

PRODUCT INFORMATION

BEHR® COPPER FORCE™ Interior Eggshell Enamel is an EPA-registered virucidal and antibacterial paint. This 100% acrylic paint &

primer

◊

kills 99.9% of viruses [SARS-CoV-2 and Feline calicivirus (EPA proxy for Human Noroviruses)] and bacteria [Staphylococcus

aureus (Staph) and Pseudomonas aeruginosa] within two hours of contact on the painted surface and lasts for up to six years..

EPA Reg. No. 32273-10. NOTE: It is a violation of federal law to use this product in a manner inconsistent with its labeling.

RECOMMENDED USES:

Ideal for properly prepared coated and uncoated interior substrates such as:

• Drywall/Gypsum Board • Plaster • Concrete • Masonry

• Brick

• Concrete Masonry Units • Wood • Engineered Wood • Steel

• Galvanized Steel

• Aluminum • Other Ferrous Metals • Other Non-Ferrous Metals • Architectural Plastics

PRODUCT SPECIFICATIONS:

Tint Bases/Max Tint Load:

No. 2190 Tintable White 122  oz/ 8  oz

No. 2193 Deep Base 116  oz/ 14  oz

Gloss: 7 – 12 @ 60°

Sheen: 17 – 22 @ 85°

Resin Type: 100% Acrylic

Weight per Gallon: 10.9 lb

% Solids by Volume: 41% ± 2%

% Solids by Weight: 54% ± 2%

VOC: < 5 g/L

ZERO VOC

• This product, like most Zero VOC paints, emits very low

amounts of VOCs.

• Most emissions occur during painting and for 48 hours

after. Some continue for two weeks or longer.

• While VOC emissions are very low, sensitive groups

such as babies and asthma/allergy suerers should

minimize exposure.

Flash Point: N/A

Viscosity: 100 – 110 KU

Recommended Film Thickness:

Wet: 6.4 mils / Dry: 2.6 mils @ 250 sq ft/gal

Wet: 4.0 mils / Dry: 1.6 mils @ 400 sq ft/gal

Coverage: 250 – 400 sq ft/gal depending on application

method and substrate porosity. Does not include the loss of

material from spraying.

APPLICATION:

Brush: Nylon/polyester

Roller: 3/8" – 3/4" nap roller cover, depending on surface

texture

Airless Spray:

Tip: .015" – .019"

Filter: 60 mesh

Fluid Pressure: 1,400 – 2,400 psi

Thinning: DO NOT THIN. Product is formulated for use at

package consistency only.

Dry Time: @ 77°F & 50% RH

To Touch: 1 hour

To Recoat: 2 hours

Full Cure: 4 weeks

Dry times are temperature, humidity, and lm thickness

dependent.

SURFACE PREPARATION:

All surfaces must be clean, free of dust, chalk, oil, grease,

wax, polish, mold and mildew stains, loose and peeling

paint, rust, and all other foreign substances.

Drywall: All drywall surfaces should be suciently sanded

smooth. Remove any remaining drywall dust prior to

priming. Allow all drywall compounds to be completely dry

prior to coating.

Wood: Remove mill glaze with sandpaper to open the pores

of the wood and follow all label instructions. For severe

stains caused by mold, mildew, algae and fungus, apple

a mildew stain removing product. Set nails and ll holes,

scratches, and gouges with the appropriate wood ller and

let dry completely. Remove all dust with a wiping cloth. Fill

gaps with a 100% acrylic siliconized, paintable caulking and

allow to dry completely. Patched and lled surfaces should

be sanded smooth and dusted prior to coating.

Masonry: Allow to cure for 30 days. The pH must be 10 or

lower prior to coating. Remove bond breakers and all form

release and curing agents. Smooth masonry may require an

adequate prole for adhesion. Remove all loose aggregate

and debris. If painting cannot wait 30 days or pH level is

above 10, allow the surface to cure 7 days and prime the

surface with an alkali-resistant primer.

Plaster: New plaster should be thoroughly dried out and

cured for a minimum of 30 days before painting. When cured,

clean using a mixed solution of one part vinegar and one part

water to remove eorescence and neutralize. Prime the area

with an alkali-resistant primer.

Steel: Minimum surface preparation is Hand Tool Cleaning

in accordance with SSPC-SP2. Remove all oil and grease from

the surface with a solvent in accordance with SSPC-SP1.

For optimal performance, use Commercial Blast Cleaning

in accordance with SSPC-SP6. Prime the area with a rust-

inhibitive primer the same day as cleaned.

Galvanized Steel: Solvent clean new galvanized metal in

accordance with SSPC-SP1 to remove oil and grease from

the surface. Pre-treat with a phosphoric acid solution or

a commercially-available etching solution. Galvanized

metal that has been passivated with chromates or silicates

may require brush blasting in accordance with SSPC-SP16

to remove these treatments. Rusty galvanizing requires a

minimum of Hand Tool Cleaning in accordance with SSPC-

SP2. Prime the area the same day as cleaned.

Shop-Primed Steel: As there is potential for many forms

of contamination during storage and transport, a thorough

cleaning is always recommended for shop-primed surfaces.

Paint exposed areas, i.e., where shop primer is abraded,

with the same material as used for shop priming to comply

with SSPC-PA 1 for touching up shop-primed surfaces. Note:

Assess the integrity of the shop primer prior to application

of subsequent coatings. Review all coatings intended for the

project and conrm the compatibility between shop and

eldapplied coatings.

Aluminum: Remove all oil and grease from the surface with

a solvent in accordance with SSPC-SP1. Prime the area the

same day as cleaned.

This information is provided “as is” and no representations or warranties, either express or implied, of merchantability, tness for a particular purpose or of any other

nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative, call

◊

A primer coat may be needed on some surfaces. See SYSTEM RECOMMENDATIONS for details.

Revised 2/2022

1 of 3

COMPLIES WITH THE BELOW AS OF 2/1/2022

SCAQMD Super

Compliant Coating

†

YES AIM YES

SCAQMD YES LEED® v.4

‡

YES

CARB SCM 2007 YES GREENGUARD®

YES

OTC Phase II YES CHPS YES

OTC YES NAHB/ICC NGBS YES

LADCO YES

† Meets SCAQMD “super-compliant” VOC standard of

<10 g/L.

‡ Please visit www.usgbc.org/LEED for additional details.

# GREENGUARD is a registered trademark of UL Company.

COPPER FORCE

™

INTERIOR EGGSHELL ENAMEL

NO. 2190 TINTABLE WHITE

Summary of content (3 pages)

PAGE 1
TECHNIC AL DATA SHEET COPPER FORCE™ INTERIOR EGGSHELL ENAMEL N O. 2 1 9 0 T I N TA B L E W H I T E PRODUCT INFORMATION COMPLIES WITH THE BELOW AS OF 2/1/2022 BEHR® COPPER FORCE™ Interior Eggshell Enamel is an EPA-registered virucidal and antibacterial paint. This 100% acrylic paint & primer◊ kills 99.
PAGE 2
TECHNIC AL DATA SHEET COPPER FORCE™ INTERIOR EGGSHELL ENAMEL N O. 2 1 9 0 T I N TA B L E W H I T E Stain-Blocking: After priming, test for stain bleed-through by applying the topcoat to a small section. If the stain bleeds through the topcoat, apply a second coat of primer and test again before topcoating the entire area. If bleeding continues, primer may need a longer dry time before applying topcoat.
PAGE 3
TECHNIC AL DATA SHEET COPPER FORCE™ INTERIOR EGGSHELL ENAMEL N O. 2 1 9 0 T I N TA B L E W H I T E PRECAUTIONARY STATEMENTS: HAZARD TO HUMANS AND DOMESTIC ANIMALS. CAUTION HARMFUL IF ABSORBED THROUGH THE SKIN OR SWALLOWED. AVOID CONTACT WITH EYES, SKIN, OR CLOTHING AND AVOID BREATHING VAPORS AND SPRAY MIST. WEAR EYE PROTECTION, GLOVES AND PROTECTIVE CLOTHING. Wash thoroughly with soap and water after handling and before eating, drinking, chewing gum, using tobacco, or using the toilet.