3D Printer Cart Assembly Guide . For assistance, please contact us: 7 TD5000_TD5001_2015_C : Copernicus © 1-800-267-8494 Slope! Pod Check out our other products online at Email www.copernicused.com : Have your packing slip ready for reference + This product is meant to be assembled by an adult. WARNING | + In its assembled state, small parts present a hazard. used under direct supervision of an adult.
Warning! Hazard Risks! Please read the warnings below for Important safety Information regarding your product. Allure to read these warnings or to follow the Instructions below could result In personal Injury or damage to your product that could cold your warranty. 9P In its assembled state, this product contains parts that can be hazardous to small children. This Sal product should be assembled by an adult. Parts [1] This product is to be used under the supervision of an adult.
D Printer Cart Parts Before beginning, you should have: ~— Additional tools required: Screwdriver QrO Adjustable wrench x1 he, ~~ Contents Box 1 4" Caster With Brake & Hardware Actual Size 4” Caster 1/4" x Bolt Safety Pinch Point Cover No Brakes double Si ® 2x woe wow) Tapeworm || dor WONANANNANANNANANY Spool Arm Holder Right : 2x (700012) 1x (51089 Side Frame Middle Frame x 1 1/4” Bolt 2x oer) x 106m) (430043) JINN Spool Arm Holder Left M6 x 19mm Screw Caster Lien © wa) Ee, Cal) 1x Handily © 10-24" x 7/8"
+ Tips for Assembly Using this Manual Watch for These Helpful Symbols i This symbol denotes a 2 Person Task. For safety, please ensure that there are two people working on steps displaying this symbol 2 Person | «Watch for this symbol throughout the Assembly Instructions. Wherever you see it, pay close H attention. The symbol denotes a step needing extra attention to ensure it is done correctly.
3D Printer Cart Assembly Guide . For assistance, please contact us: TD5000_TD5001_2015_A : Coniferous — © 1-800-267-8494 o Fos Check out our other products online at Email www.copernicused.com Have your packing slip ready for reference Dear Educator, Thank you for purchasing one of our products. I hope the assembly of your 3D Printer Cart went well. If you have any questions, or concerns, or ideas for how we can improve, please call us at 1-800-267-8494, where someone will be happy to help.
ual Size: will need: (Not to Scale) Side Frame 1x Stretcher 2x Attach Stretchers to Side Frame | Make sure Side Frame m channels face inwards. You will need: (Not to Scale) Side Frame 1x Attach other Side Frame Make sure Side Frame H channels face inwards. 6 TD5000-TD5001 Version C Released 14 September 2015 Copernicus Educational Products Inc.
You will need: (Not to Scale) Middle Frame 1x Attach Middle Frame Position main frame upside down to attach Middle Frame. Actual Size: © 4x You will need: (Not to Scale) 4” Caster With Brake & 4” Caster without Caster Safety Pinch Point Cover Brakes Wrench 2x (41013) 2x (41014) 1x Install Casters Place lock nut over threaded post of caster. Locking caster are Installed on front of cart, opposite of cable wrap. Non-locking casters installed back of cart, same side as cable wrap.
You will need: (Not to Scale) : ig Tub F : Re ally Big Tub Frame Adjustable wrench x1 Install Really Big Tub Frame Slide Really Blg Tub frame Into cart frame opposite of cable hooks on Middle Frame and install safety bolts ush frame all the way in & then install bolts. Do not over tighten. Actual Size: You will need: (Not to Scale) Handle 1x Attach Handle Note orientation of handle In diagram. CABLE HOOKS 8 TD5000-TD5001 Version C Released 14 September 2015 Copernicus Educational Products Inc.
You will need: (Not to Scale) Top Drawer Stretcher 2x Attach Top Drawer Stretchers Do not fully tighten hardware until the end of Stop 8. Note orientation of Top Drawer Stretchers. ® Drawer Slides slide out towards the front, opposite to the cable hooks on the back. Note channels face inward Actual Size: You will need: (Not to Scale) Laptop Tray (drawer slides attached) 1x Install Laptop Tray Completely slide Laptop Tray Into drawer slides. Tighten hardware from Step 7.
Actual Size: ANN | ® ax You will need: (Not to Scale) Printer Table 1x Install Printer Table Tighten screws until flush with shelf, B® otherwise they will stick out above printer shelf surface. T= )memo © o= You will need: (Not to Scale) Spool Holder Spool Arm Holder 1x 2x Install Spool Holder Arms Spool Holder Arms are adjustable for different printers. Choose height where | spools will not rest on printer body. Spool holder rests in place.
You will need: (Not to Scale) Tiny Tub Install Tiny Tub in Holder Actual Size: You will need: (Not to Scale) Power Strip Double Sided Foam Tape 2x (700012) Attach Power Strip Attach Power Strip to the cart by using the supplied double sided tape. Install on the same side as the handle. Install on the stretcher shown below. Wrap cord around hooks on back of unit. Flea eR EY Apply Double Sided Tape oy 11 TD5000-TD5001 Version C Released 14 September 2015 Copernicus Educational Products Inc.
Actual Size: You will need: (Not to Scale) Open Tub Really Big Tub TD5000 4x 7 1x Open Tub Really Big Tub 12 Install Tubs res TOG, pre TBO =e Printer and accessories not included. Printer and accessories not included. TD5000-TD5001 Version C Released 14 September 2015 Copernicus Educational Products Inc.
