User`s guide

xii Contents
Minimum program setup requirements . . . . . . . . . . . . . . . . 11-2
Defining a Time-Based Stimulus . . . . . . . . . . . . . . . . . . . . . . . 11-3
Overview of Stimulus Generation . . . . . . . . . . . . . . . . . . . . . 11-3
The Stimulus Editor Utility . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5
Stimulus Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6
Configuring Stimulus Files . . . . . . . . . . . . . . . . . . . . . . . . 11-6
Starting the Stimulus Editor . . . . . . . . . . . . . . . . . . . . . . . . 11-7
Defining Stimuli . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-8
Example: piecewise linear stimulus . . . . . . . . . . . . . . . . . . 11-8
Example: sine wave sweep . . . . . . . . . . . . . . . . . . . . . . 11-9
Creating New Stimulus Symbols . . . . . . . . . . . . . . . . . . . . . 11-10
Editing a Stimulus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12
To edit an existing stimulus . . . . . . . . . . . . . . . . . . . . . . 11-12
To edit a PWL stimulus . . . . . . . . . . . . . . . . . . . . . . . . 11-12
To select a time and value scale factor for PWL stimuli . . . . . . . 11-12
Deleting and Removing Traces . . . . . . . . . . . . . . . . . . . . . . 11-13
Manual Stimulus Configuration . . . . . . . . . . . . . . . . . . . . . . 11-13
To manually configure a stimulus . . . . . . . . . . . . . . . . . . . 11-13
Transient (Time) Response . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-15
Internal Time Steps in Transient Analyses . . . . . . . . . . . . . . . . . . . 11-17
Switching Circuits in Transient Analyses . . . . . . . . . . . . . . . . . . . 11-18
Plotting Hysteresis Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-18
Fourier Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-20
Parametric and Temperature AnalysisChapter 12
Chapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
Parametric Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2
Minimum Requirements to Run a Parametric Analysis . . . . . . . . . . 12-2
Overview of Parametric Analysis . . . . . . . . . . . . . . . . . . . . . 12-3
Example: RLC Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3
Entering the schematic . . . . . . . . . . . . . . . . . . . . . . . . 12-3
Running the simulation . . . . . . . . . . . . . . . . . . . . . . . . 12-4
Using performance analysis to plot overshoot and rise time . . . . . 12-5
Example: Frequency Response vs. Arbitrary Parameter . . . . . . . . . 12-8
Setting up the circuit . . . . . . . . . . . . . . . . . . . . . . . . . . 12-8
Displaying results in Probe . . . . . . . . . . . . . . . . . . . . . . 12-9
Temperature Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-11
Minimum Requirements to Run a Temperature Analysis . . . . . . . . . 12-11
Overview of Temperature Analysis . . . . . . . . . . . . . . . . . . . . 12-11