USER GUIDE HARDWIRED CONTROL UNIT
Contents 1. Introduction ........................................3 Alarm System.......................................3 Keypad.................................................4 Proximity Tags .....................................4 Mains Power Failures...........................7 About this Guide...................................8 2. Everyday Operation ...........................9 Setting the System ...............................9 General Procedure.........................10 Timed Set......................
1. Introduction Alarm System The alarm system described in this book comprises a control unit (model 9651), one or more keypads, and various detectors. The control unit houses a main controller, power supply, stand-by battery and an optional communication device. It is normally fitted in a safe place out of sight (for example, under the stairs). The detectors are installed in various places, or zones, around the premises. If something triggers a detector, the detector signals this to the control unit.
1. Introduction Keypad Your alarm system is fitted with a 9930 or 9940 keypad, from which you can set and unset the system. Figures 1 and 2 show the main features of these keypads. Refer to "4. Special Functions" on page 18 for information about other functions available from them. The system will not accept commands from the keypad until you identify yourself with an access code or proximity tag. It can store 50 access codes, which may contain four or six digits1, giving secure access for up to 50 users.
1. Introduction These may show nothing until a user is identified. Sensitive area Present proximity tags by touching them to this area. Alert lamp (see page 20) Flashes to highlight unacknowledged alarm, fault or tamper conditions. Glows for acknowledged conditions. Goes out when all conditions are rectified. Service lamp Glows if the system needs an Installer reset. Mains lamp Glows when using mains power. Flashes when using stand-by battery.
1. Introduction These may show nothing until a user is identified. Alert lamp (see page 20) Flashes to highlight unacknowledged alarm, fault or tamper conditions. Glows for acknowledged conditions. Goes out when all conditions are rectified. 2-line 16-digit liquid crystal display The first line shows: - unset: time and date - set: level(s). The second line shows Installer-configured text, often the control unit model number. The display may show only time and date until a user is identified.
1. Introduction Mains Power Failures The control unit indicates mains power failures using alerts. If the supply has since been restored, the alert will show the condition as inactive. For instructions on how to view and acknowledge alerts, refer to page 19.
1. Introduction About this Guide The rest of this guide tells you how to use the system: 2. Everyday Operation Tells you how to set and unset the system. 3. After an Alarm Tells you how to switch off the sounders after an alarm, view what caused the alarm and reset the system so that it can be used again. 4. Special Functions Tells you how to use more advanced features, some of which are available only to the master user.
2. Everyday Operation During installation, your installer programs the system to create an exit route and entry route for your premises. When setting the system, you must follow the exit route. When unsetting the system, you must follow the entry route. If you stray from these routes, you may cause a false alarm. Setting the System There are several different methods for setting the system. Each level can use a different method, although not all methods are available in all cases.
2. Everyday Operation General Procedure To set the system: 1. Secure all doors and windows. 2. At the keypad, key in an access code (or present a tag). The display shows (for example): 3. 4. 5. System OK Set? Press the appropriate level key. Note: If you press y without a level key, the system sets Level A (Full Set). If you have omitted a zone (see page 20), the display shows (for example): Press y to continue with the zone omitted. If you do not want to omit it, press X to exit.
2. Everyday Operation Timed Set With Timed Set, the system sets after a programmed exit time has expired. The time starts when you press a level key, or when you press y to accept an omitted zone. Your installer will have made the exit time long enough for you to leave the premises and secure the final door5. When using Terminated Set (see below), your installer may have programmed the system to set after the exit time even if the exit terminate button is not pressed.
2. Everyday Operation waiting for an exit time. The system gives a double "beep" to show that it is set. Note: Instant Set is not available for Level A (Full Set). Keyswitch Set If your system is fitted with a keyswitch, you can use it to set the system. If it is a three-position keyswitch in a single system, you can use it to set Level B. The keyswitch initiates setting, which then completes in accordance with the programmed exit mode. You do not need to enter an access code or present a tag.
2. Everyday Operation Investigating Setting Problems This section offers general guidance. If you need assistance to resolve a problem, contact your installer. Detector Active If something is triggering a detector at the end of the exit procedure, the system will not set. Depending how your installer has set up the system9, internal or external sounders may operate. The display shows which zone (or zones) is active. To set the system: 1. 2. 3. 4. 5.
2. Everyday Operation Other Problems The system informs you of problems through alerts. These are warnings communicated through the keypad display and lamps. If your system is set up to hide status information after 30 seconds10, enter an access code or present a tag to activate the keypad display and lamps. Depending on the nature of the problem, you may need to reset the system or call an installer to do this for you (see page 17).
2. Everyday Operation Unsetting the System WARNING: If you enter your premises and an internal alarm starts, there may be an intruder. You can unset the system from a keypad or keyswitch. When you open an entry door, the system starts an entry timer. There are four entry timers so that different entrances can use different times. During the entry time, the keypads give a "galloping" entry tone to warn you that the timer is running. If you exceed the entry time, an alarm will occur.
2. Everyday Operation Aborting False Alarms If your system is connected to an ARC and you accidentally cause an alarm, you normally have at least two minutes before the ARC calls the police. Alarm Abort12 enables you to cancel a false alarm by entering a valid access code during this period (which is set by the ARC). If Alarm Abort is not enabled on your system and you often exceed an entry timer that is already set to the maximum, ask your installer about Alarm Abort.
3. After an Alarm Responding to a Fire Alarm IMPORTANT: The system gives a fire alarm by sounding a two-tone warning from the keypads and alarm sounder. The display shows (for example): 1. Evacuate the premises. Do not attempt to unset the alarm. 2. If there is evidence of fire, call the Fire Brigade. 3. Only when the premises are safe, proceed as for other alarms.
4.
Appendix Viewing Alerts The system records alarms, faults and tampers as alerts. It usually displays the first alert automatically when you unset the system but you can view alerts at any time by pressing 1. Viewing an alert acknowledges it. The Alert lamp ( ) flashes for unacknowledged alerts and glows for acknowledged alerts. If the condition that caused the alert still exists, the alert message shows "Active". If the condition no longer exists, the message shows "Inactive". To view alerts: 1.
Appendix Omitting Zones Your system may be programmed so that you can omit individual detectors. This enables you to ignore alarms coming from faulty detectors in non-critical positions. Refer to the table on page 32 to see which zones can be omitted in your system. To omit a zone: 1. Key in an access code (or present a tag). 2. Press 2. This display shows: Omit Zone? 3. 4. Press the number of the zone you want to omit (for example, press 07 to omit zone 7) and then press y.
Appendix Requiring User Code before Installer Code You can specify that a user code must be entered before the installer code to access the installer menu. This enables you to supervise installer activities. 1. Key in an access code (or present a tag). 2. Press 3 to toggle between requiring and not requiring a user code. The display shows (for example): UserCode req=OFF 3. When you turn user code on or off, the keypad confirms with a double "beep". Press y.
Appendix Turning the Chime On and Off Your system may be programmed so that a chime tone sounds when certain doors are opened while the system is unset. You can turn this on and off. 1. Key in an access code (or present a tag). 2. Press 7 to toggle chime on and off. The display shows (for example): Chime = ON When you turn chime on, the keypad confirms with a double "beep". 3. Press y. Testing the Sounders You can test that the sounders and strobe are working.
Appendix Testing Zones You can set the system so that it will allow you to walk around and test each of the detectors (a walk test). Do this when the premises are empty to avoid other people triggering movement detectors before you do, which would confuse the results of the test. If a detector fails the test, contact your alarm company and ask them to check the system. Notes: 1. 2. You can abandon the test at any time by pressing y.
Appendix When the system is delivered from the factory, all access codes are set to default values. Depending how your installer has set up the system13, access codes may contain four or six digits. The default for the master user (U01) is "1234" when four-digit codes are in use and "123456" when six-digit codes are in use. The master user should change this immediately to a code known to no one else. The other defaults are "X002" for U02 through to "X050" for U50.
Appendix To delete an access code: 1. Follow the procedure for setting an access code. 2. In step 5, key in "0000". Changing User Names The system can store up to 12 characters for each user name, including spaces and punctuation marks. The default names are in the form User nn. You can change the name when you set the access code. In step 3 of the procedure on page 24, the display shows the current user name with a flashing cursor under the first letter.
Appendix Proximity Tags Each normal user (Users 2 to 50) can have a tag, an access code or both. You cannot assign a tag to the master user (U01), the installer (U00), or the duress code (U51). You set up a tag in a similar way to an access code (see page 24). Instead of entering a new access code for the user, present the tag. The system learns the identity of the tag and links it to the user number. The keypad confirms that the tag has been learned with a double "beep".
Appendix Appendix.
Appendix Message Meaning System Tamp System tamper reset Rst System Tamper System tamper Tamper F== Rstr Forbikobler keypad == tamper reset Tamper K== Keypad == tamper reset Rstr Tamper Z== Zone == tampered with Tamper Z== Tamper in zone == during the day Tamper Z== Rstr Zone == tamper reset Tech Z== Alarm Technical alarm in zone == Tech Z== Rstr Technical alarm in zone == reset Tel Line Fault Line fault on telephone line Tel Line Rstr Line fault reset on telephone line U== # Set User == set level # U== #
NOTES Page 29 497282
Appendix NOTES Page 30 497282
Log Messages NOTES 497282 Page 31
Your Installation Zone 1 2 3 4 5 6 7 8 Company Name Control Unit Model Exit Time Bell Duration Engineer Reset Communicator Fitted Meets DD243: 2004 Description A A B Contact Number (Day) Contact Number (Night) B C C D Omit Chime Allow Entry Time D Dual Key PA Fire Enabled? Meets PD 6662 / prEN 50131-1: 2004 Medical Note: If this table has not been completed, ask your Installer for the information.
