i-on16 © Cooper Security Ltd. 2012 IN NO EVENT WILL COOPER BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL , OR INDIRECT LOSS OR DAMAGE, INCIDENTAL DAMAGES, STATUTORY DAMAGES, EXEMPLARY DAMAGES, LOSS OF PROFITS, LOSS OF REVENUE, LOSS OF ANTICIPATED SAVINGS, LOSS OF BUSINESS OR OPPORTUNTIY, LOSS OF GOODWILL OR INJURY TO REPUTATION, LIQUIDATED DAMAGES OR LOSS OF USE, EVEN IF INFORMED OF THE POSSIBILITY OF SUCH DAMAGES.
i-on16 Contents 1. Introduction .......................................................................... 7 Setting and Unsetting ................................................................ 8 Alarms and Reset .............................................................................. 9 Security Levels ................................................................................. 9 24 Hour Alarms................................................................................. 9 Communications .
i-on16 Walk test ....................................................................................... 57 Outputs ......................................................................................... 59 Remotes ........................................................................................ 61 Radio Hold Up Alarms ...................................................................... 62 Proximity Tags................................................................................
i-on16 Compliance Statement The i-on16: Is suitable for use in systems designed to comply with PD6662:2010 at Grade 2, and environmental class II. Is suitable for use in systems designed to comply with the requirements of EN50131-3 at Grade 2 and environmental class II. Complies with the requirements of EN50131-6:2008 at Grade 2 and environmental class II. When fitted with the appropriate communicator (see the relevant Installation Guide) this product is compliant with EN 50136-1.
i-on16 This page is intentionally blank.
i-on16 1. Introduction The i-on16 is a wireless intruder alarm system intended mainly for use in domestic and small commercial properties. The heart of the i-on16 system is the control unit and its keypad. The control unit contains the main wireless receiver, the power supply and stand-by battery. The stand-by battery can keep the alarm system going for up to 12 hours if the mains supply fails. Connected to the control unit by cable are the keypads.
1 Introduction i-on16 1 2 3 A B 1. Two button Hold Up Alarm with tilt switch. 2. Two button Hold Up Alarm. 4 5 3. Four button remote control. 4. Keypad. 5. Wireless arming station. 6 6. Door Contact/Universal Transmitter. 7 8 7. Smoke Detector. 8. Passive Infra Red. 9 9. External siren/strobe. Figure 1.
i-on16 1. Introduction into protected areas. Readying the system to start an alarm when someone moves into a protected area is called “setting” the system. Disarming the system so that people can move freely is called “unsetting” the system. Alarms and Reset When the system starts an alarm it usually includes activating sounders and strobes and sending messages to an Alarm Receiving Centre (ARC). The ARC may then call the police or other security service to come and investigate the alarm.
1 Introduction i-on16 Communications Your system may be fitted with a communication module that allows the control unit to send alarm information over the telephone network. Controls and Displays Figure 2 shows the controls and displays available on the keypad. 1. LCD display . 1 2. Programming keys. 2 3. Navigation key 7 4. Setting and 3 unsetting keys. 5. Hold Up Alarm (HUA) keys. 66. Alpha/numeric keys. 4 5 7. Set/Unset status LEDs. Figure 2.
i-on16 1. Introduction Deletes characters when editing names. Press this key to confirm a decision and save any changes. a) Moves the display to a higher level of the menu. b) Press this key to abandon your decision when the display shows “Are you sure Y/N?” Press this key to gain access to the Menu. 1 to 0, Used to key in access codes. Can also be used to key in *, # text for names, and telephone numbers. # Used when keying in text: press to change between capitals or small letters.
1 Introduction i-on16 Note that the installer can disable these LEDs in order to hide the state of the system (to comply with EN50131). Alternatively, the installer may have programmed the LEDs to glow for 30s immediately after setting, and then to go out. Detectors or Zones? When talking about alarm systems, people tend to use the words “detectors” and “zones” interchangeably. Most of the time this doesn‟t matter, but occasionally it can cause some confusion.
i-on16 1. Introduction For details on how to add and remove users see page 36 . Identifying Users The control unit identifies each user internally by a unique number in the range 001 to 016. When a Master User adds or edits other users the keypad shows user numbers as “User nnn”, for example “User 001” or “User 015”. To help Master Users identify other users the control unit allows each user to have a 12 character name. The Master User keys in the name when adding the user to the system.
1 Introduction i-on16 Codes 0000 to 9999 are available but Cooper Security Limited recommends that you avoid easily memorised codes such a 0000, 9999 or 4321. The installer has their own access code which they cannot use to set or unset the alarm system. Neither can they use that code to change details of other users registered to the system. Similarly, the Master User code has no access to any installer programming menus.
i-on16 1. 2. 3. 4. 5. 1. Introduction Full Set. Part Set. (Programmable, see page 74.) Unset. Transmit LED. A B Figure 3. Remote control Buttons. Each remote control has a unique electronic identity. When you assign a remote control to a user you teach the identity to the control unit. You may assign one (and only one) remote control to each user. Radio Hold Up Alarms (HUA) A radio HUA is a two button transmitter, used to start a Hold Up Alarm. (Hold Up Alarms used to be known as Panic Alarms.
i-on16 2. Alarms The table below shows the different kinds of alarms possible. Type of Alarm Intruder Signal (see note) Started by: Loud warbling tone from siren. Normal alarm or entry route zone activated when system is set. Fire Pulsing tone from siren. Fire zone activated at any time. Hold Up Loud warbling tone from siren HUA zone or radio Hold Up Alarm transmitter activated at any time. 24 hour zone activated at any time. Pressed on keypad.
i-on16 2. Alarms 1. Make sure it is safe to enter the premises: 2. Either key in your access code OR present your proximity tag. The bottom line of the display shows the first zone to alarm. 3. 4. Press or to see the name of the zone (if the installer has programmed one), for example: Press to reset the system. The system returns to standby, and is ready to set again. (The top line may show the installer‟s name.
2. Alarms i-on16 Press or to see the name of the zone (if the installer has programmed one), for example: Press to restore the display to normal. If you wish to see any other zones that were triggered during the alarm, look in the log (see page 52). If You Cannot Reset the System Your system may be programmed so that it has to be reset by an installer after an alarm.
i-on16 2. Alarms When you talk to the alarm company, they will ask about the circumstances of the alarm, and also for the code you recorded from the display. If the alarm company decides that an engineer does not need to visit you, then they will give you another four digit code (the “anti-code”). Key in the anti-code at the keypad. The system will reset, and you can carry on using it as before.
2. Alarms i-on16 Function End this call (and let the control unit contact the other destinations for this alarm) Play „Home‟ and „alarm‟ message again Clear down (and do not call any of the other destinations for this alarm). Key „5‟ „3‟ „9‟ Note: When the called party answers a speech dialler call there is a six second delay before the control unit starts playing the home message. Alerts (or Why is it Beeping?) From time to time the control unit may detect that there is a problem with the system.
i-on16 2. Alarms alerts the keypad will return to its‟ standby screen and, after a few seconds, the rim of the navigation pad will glow green. In addition the keypad will stop beeping. OR: Press . The rim of the navigation pad will stay red and the system will show the text of the alert the next time you key in an access code. (The keypad will stop beeping.) Note: 1. The system will not alert you to short (less than 10s) interruptions of mains power.
i-on16 3. Setting and Unsetting There are two main ways of setting and unsetting your alarm system: either from a keypad or from a remote control. This chapter is split into two halves, dealing with each of those methods in turn. In case you are not familiar with some of the terms used in this book: “Full Set” means that all the detectors in the system are being monitored. If there is any activity on any detector then the system will start an alarm.
i-on16 3. Setting and Unsetting Setting 1. Starting to Set Do this: The display shows: a. Make sure the system is idle. Secure all the windows and doors. (The top line may show the installer‟s name.) b. Either key in your access code. As you key in your code the display shows a “*” for each digit. OR present your tag. Quick Set: In a part setting system, quick set removes the need to use an access code or tag to start setting.
3. Setting and Unsetting i-on16 2. Selecting What to Set: Do this: a. The display shows: The bottom line of the display shows the first item in the setting options menu. ↕ Press or to select the option you want. ↕ The bottom line of the display shows each item from the rest of the menu in turn. 3.
i-on16 3. Setting and Unsetting top line of the display shows the part of the system being set, the bottom line shows the remaining exit time (in seconds). b. Leave by the designated exit door. Remember to close the door. At the end of the exit time the system sets. Exit Terminate Button: a. Press . The keypad sounds the exit tone. The top line of the display shows the part of the system being set, the bottom line shows “Exit Terminate”. b.
3. Setting and Unsetting i-on16 door is closed). The top line of the display shows the part of the system being set, the bottom line shows “Final Door Set”. b. Leave by the designated exit door. c. Close the door. The system sets. Lock Set: a. Press . The keypad sounds the exit tone (an interrupted tone if the final exit door is open, a continuous tone if the exit door is closed). The top line of the display shows the part of the system being set, the bottom line shows “Lock Set”. b.
i-on16 3. Setting and Unsetting One of four LEDs glows to show which part of the system is set. Note: The installer may have disabled the LEDs to ensure that the alarm system meets the appropriate standards. In addition, the installer may have programmed the system to briefly flash the strobe light on the external sounder when the system sets. Changing Your Mind If you want to stop setting then press (unset key).
3. Setting and Unsetting i-on16 SETTING FAULTS Z041 Back door Figure 5. Keypad Display Showing Active Zone Investigate the zone listed on the display and see if you can rectify the fault. If your system has been programmed to then you can “omit” the affect zone beforehand (see page 35 for instructions on how to omit zones before setting the system). Other Reasons Why the System May Not Set There are several other events that can show fault warnings on the keypad and prevent your system from setting.
i-on16 3. Setting and Unsetting Message Meaning The system has detected a User fault not covered by the above categories. 1 Override by: Your system may be programmed so that only the Installer can override this fault. Unsetting the System Using a Keypad When unsetting the system do not stray from the entry route designated by the installer. If you do so then you will cause an alarm. Start the Entry Procedure Do this: 1. Enter by the designated entry door or route.
3. Setting and Unsetting i-on16 LEDs “A” to “D” should be dark, showing that the system is unset. Note: The installer may have disabled the LEDs to ensure that the alarm system meets the appropriate standards. Using Radio Keypads and Remote Controls. Using a Radio Keypad Setting Secure all your windows and doors. Make sure the system is idle, and that you can hear the warning tones from the sounders. 1. Key in a valid access code. 2.
i-on16 3. Setting and Unsetting Using a Proximity Tag With a Radio Keypad If you wish to use a Proximity Tag with the radio keypad in place of an access code, then hold the tag up against the proximity tag sensor (see Figure 6). The keypad glows blue and gives a “click” to show that it has recognised the tag. Proximity tag sensor “Transmit” LED Figure 6. Radio Keypad Note: The radio keypad does not show the status of the alarm system at all.
3. Setting and Unsetting i-on16 Transmit LED Full Set Part Set A B (Programmable) Unset Figure 7. Remote Control Button Functions. The keypad sounds the exit warning tone. 2. Complete setting using the method programmed by the Installer (see “3. Finishing Setting” on page 24). Unsetting 1. Enter by the designated entry door. 2. Press on your remote control. The system unsets. At this point the system displays the standby screen.
i-on16 4. Administration To make changes to the way your system works you must enter the Menu. Your degree of access to the Menu depends on what type of user you are: Master User or Normal User. A Master User has access to all the options of the Menu. A Master User can add, change, or remove users and has full access to the system options menu. A Normal user has very limited access to the Menu: they can change their own access code, switch Chime on or off, and operate any outputs.
4. Administration i-on16 The rest of this chapter describes each of the main options in the Menu. Editing Text For many of the items that you can program, the control unit lets you assign a 12 character name. To key in text for the name press each number key one or more times to obtain the letter you want (the letters of the alphabet appear on the keys in the same arrangement as on many mobile phones, see Figure 8.) Press # to change between capitals and small letters.
i-on16 4. Administration Omitting Zones You may wish to prevent a zone causing an alarm. For example, if your garage door is protected by a detector, but you wish to leave it unlocked for the delivery of a parcel, you may wish to omit that detector when you set the rest of the alarm system. Provided that the Installer has programmed your system to allow this, then, to "Omit" a zone. 1. Make sure the display shows the standby screen. 2. Press 3.
4. Administration i-on16 If you change your mind then press again so that the end of the line shows an "I" (for Included). 7. Repeat steps 5 and 6 for any other zone you wish to omit (or include). 8. Press to store the changes you have made. The keypad gives a double “beep” confirmation tone. 9. Press to leave the Menu. The keypad gives a double “beep” confirmation tone.
i-on16 4. Administration Edit their own user code, and delete or add their own proximity tag, remote or radio HUA. Guards and Set Only users have no access to the Menu. Editing Existing Users This menu lets you change the details for an existing user. Name Use this option to give the user a 12 character name. 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). 4. Press . 5. Press .
4. Administration 9. Press . The bottom line shows: 10. Press . The display shows the current name given to the user, and places a cursor at the beginning of the name. i-on16 11. Key in the name from the keypad. See Editing Text on page 34. 12. Press when finished. The keypad gives a double “beep” confirmation tone.
i-on16 7. Press . The bottom line of the display shows the name of the first in a list of the users already programmed into the control unit. In the example shown the name is “User 01”. 8. 4. Administration Press or to display the user you wish to edit. (Alternatively, if you already know their user number, you can key that in and the display will show that user immediately.) 9. Press . The bottom line shows: 10. Press . 11.
4. Administration i-on16 Access Code No user can change any other user‟s access code. (A Master User can create an access code for a new user when they first add the user to the system, see page 48.) Any user, except a Guard or Set Only user, can change their own code as follows: 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). 4. Press . .
i-on16 8. 4. Administration Key in the new access code . Access codes are four digits long. When you press the last digit of the access code the display asks you to key in the same access code again. 9. Key in the same digits again, in the same order. The keypad gives a double “beep” confirmation tone.
4. Administration b) Press . c) Press or . until the bottom line of the display shows your own user name. d) Press . e) Press or . until the bottom line of the display shows: f) Go on to step 8. i-on16 If you are a Normal User: 6. Press . 7. Press until the display shows: 8. Press .
i-on16 4. Administration If you have a proximity tag and want to know who it belongs to then use the Test - Prox Tag menu option, see page 52 . Remote Controls No user can change any other user‟s remote control. (A Master User can register a remote control for a new user when they first add the user to the system, see page 48.) Any user except a “Guard” or “Set Only” user can register a remote control for themselves as follows: 1. Make sure the display shows the standby screen. 2. Press 3.
4. Administration i-on16 If you are a Normal User: 6. Press . 7. Press until the display shows: 8. Press . The display asks you to press one of the buttons on the remote control. Note: If you already have a device allocated to you then the screen will display “Delete Remote?”. See page 47. 9. Press any button on the device that you wish to register. The keypad gives a double “beep” confirmation tone.
i-on16 4. Administration Radio Hold Up Alarms (HUA) No user can change any other user‟s radio HUA. (A Master User can register a radio HUA for a new user when they first add the user to the system, see page 48.) Any user except a Guard or Set Only user can register a radio HUA for themselves. Note: While you are registering a new radio HUA the control unit will not respond to an alarm signal from any radio HUA it has already learned. 1. Make sure the display shows the standby screen. 2. Press 3.
4. Administration 6. Press . 7. Press until the display shows: 8. Press . i-on16 The display asks you to press both of the buttons on the Hold Up Alarm. Note: If you already have a Hold Up Alarm allocated to you then the screen will display “Delete Hold Up Alarm?”. See page 47. Press to leave the menu without deleting the Hold Up Alarm, or if you change your mind and do not wish to add a Hold Up Alarm. 9.
i-on16 4. Administration Deleting Remote Controls and Radio HUAs If you have lost a remote control, prox tag or radio Hold Up Alarm assigned to you then you should delete it from the system to make sure that no unauthorised person can use it. 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). 4. Press . . If you are a Master User: (otherwise go to step 6) 5. Press . a) Press . b) Press . c) Press or .
4. Administration 8. Press . The bottom line of the display asks if you wish to delete the device you selected. 9. i-on16 Press The keypad gives a double “beep” confirmation tone. The keypad display shows: The control unit has deleted the identity of the Hold Up Alarm (or other device you selected). followed by: To register a new device, re-enter the Menu and select Users - Edit User.
i-on16 5. Press . 6. Press . The display shows a default user name, for example: “User 04”. Edit the name (for hints on editing text see page 34). 7. Press or to show the type you want to assign to the new user and then press . The display asks you to assign a new user code. 9. Press when you have finished editing the name.
4. Administration i-on16 The display then asks you to press a button on any remote control that you want to assign to the user. 12. Press a button on a remote control (one that is not currently registered to any other user). If you do not have one press . The display finally asks you to press both buttons on any radio HUA that you want to assign to the new user. 13. Press both buttons on a radio HUA that you wish to assign to the user.
i-on16 4. Press . 5. Press . 6. Press until you see: 7. Press . The bottom line of the display shows the first user in a list of the users recognised by the system. 8. Press or . until the bottom line of the display shows the user you wish to delete. 4. Administration Note: The control unit will not allow you to delete User 01. 9.
4. Administration i-on16 Viewing the Log The control unit keeps a log of the last 265 events (for example, alarms and setting/unsetting events). To read the log: 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). 4. Press until you see:. 5. Press . . The display shows the most recent event recorded in the log. 6. Press or to scroll through the log. shows older events, shows more recent events. 8.
i-on16 4. Administration User 18 Panel (Control Unit) User 19 Keyswitch User User 20 ARC Remote Reset Testing the System If you think that your system is not working correctly then a Master User can use the Test option to test various peripherals. If the test confirms that part of the system is not working then contact your installer. The Test option also lets you check the identity of Remote controls, Hold Up Alarms and Tags. Sirens & Sounders 1. Make sure the display shows the standby screen.
4. Administration i-on16 keypad shows for a few seconds: a) Press . The keypad gives a double “beep” confirmation tone. The keypad display shows: The control unit turns on the external radio sirens. Check that you can hear them. b) Press again to turn the sirens off. The keypad gives a double “beep” confirmation tone. The keypad display shows: 8. Press when you have finished this test.
i-on16 4. Administration 12. Press . The display shows the next item in the list of tests. 13. Press . a) Press . The keypad gives a double “beep” confirmation tone. The keypad display shows: The control unit sounds a test tone on the loudspeakers. Check that you can hear them. b) Press again to turn the loudspeakers off. The keypad gives a double “beep” confirmation tone.
4. Administration b) Press again to turn the keypad sounders off. i-on16 The keypad gives a double “beep” confirmation tone. The keypad display shows: 17. Press when you have finished this test. 18. Press to leave the siren test menu. Keypad 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). 4. Press until you see: 5.
i-on16 8. 4. Administration Press each key once. The bottom line of the display shows the key you pressed. Press both radio HUA keys together to test. As you press the function keys on the keypad the display shows their name, for example: 9. Press to end the test. Walk test The Walk Test menu allows you to test detectors without starting an alarm. To “walk test” an alarm system you operate each detector in the system.
4. Administration 4. Press until you see:. 5. Press . The bottom line of the display shows: 6. Press until you see: 7. Press . The bottom line of the display shows: 8. i-on16 Press or to turn a chime tone on or off. When the chime tone is on, the keypads and loudspeakers will sound a chime tone for each zone that triggers while you are performing the walk test. 9.
i-on16 4. Administration the detectors ready for testing. The top line of the display shows you how many detectors remain to be tested. 10. Walk round and trigger each detector. The display shows an "A" at the end of the line each time a detector is triggered. If you have enabled the Chime then every time you trigger a detector the keypads and loudspeakers give a double tone chime. Note that you cannot test HUA, 24 hour or fire zones. 11.
4. Administration 6. Press until you see: 7. Press . The bottom line of the display shows the first in a list of the outputs allocated for your use. If the output has a name programmed for it, that will appear on the bottom line instead of the output number. 8. Press or to display the output you wish to test. a). Press . The keypad gives a double “beep” confirmation tone.
i-on16 4. Administration Remotes 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). 4. Press until you see:. 5. Press . . The display shows: 6. Press until you see: 7. Press . 8. The display asks you to press any button on the remote you wish to test.
4. Administration i-on16 button you pressed and the strength of the signal received by the system from the remote. If the signal strength is less than 4 you should contact your installer. a). Press all the other buttons on the device. Each time you press a button on the remote the keypad gives a double “beep” confirmation tone. For each button you press you will see a similar message, for example: b) Press a button on any other device that you wish to test.
i-on16 5. Press . The display shows: 6. Press until you see: 7. Press . The display asks you to press both buttons on the radio HUA you wish to test. If there are no radio HUAs available the display briefly shows: 8. 4. Administration Press and hold down both buttons on the Hold Up Alarm you wish to test (you should hold the buttons down until the transmit LED on the radio HUA flashes).
4. Administration a) i-on16 Press and hold the buttons on any other HUA that you wish to test. Each time you activate a HUA the keypad gives a double “beep” confirmation tone. The display shows information for any radio HUA allocated to a user of the system, for example: 9. Press to end the test. Proximity Tags 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). 4.
i-on16 8. 4. Administration Hold the prox tag against the front of the keypad. The keypad gives a double “beep” confirmation tone. a) The bottom line of the display shows the user that the prox tag is allocated to. (Any name programmed for the user will appear in place of the user number.) Hold any other prox tags that you wish to test up against the keypad (one at a time). The keypad gives a double “beep” confirmation tone.
4. Administration 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). 4. Press until you see:. 5. Press . . The bottom line of the display shows: 6. 8. Press .
i-on16 3. Key in your access code (or present a tag). 4. Press until you see:. 5. Press . The bottom line of the display shows: 6. Press until the display shows: 7. Press . The top line of the display shows “Set the date” and the bottom line shows the current date in number format (day/month/year). The day is highlighted. 8. 9. Key in the correct date. Use the format dd/mm/yyyy. If the days or months are “9” or less then key in a leading zero.
4. Administration i-on16 seven in the morning will be “07:06”. 11. Press . The keypad gives a double “beep” confirmation tone. The keypad display shows: The control unit saves you changes and the display returns to the date and time menu option. Note: The internal clock adjusts itself for daylight saving in Spring and Autumn. Programming Outputs During programming the installer may allocate some outputs so that they can be reprogrammed by an Master User.
i-on16 6. Press until the display shows: Note: This option is only visible if the installer has allocated some outputs to you. 7. 4. Administration Press . The top line of the display shows the address of the first available output. The bottom line shows the name of the output (if the installer has given it one). 8. Press or to display the output you wish to edit. 9. Press .
4. Administration 13. Press The display shows: i-on16 14. Press . There are two options to “Latched”. “Yes”. The output stays on until a user deliberately turns it off. In addition, you can program the output to come on and go off at fixed times (see the next section). “No”. The output goes on when a user turns it on, but then goes off again after a set time. You can program the length of time the output remains on. 15.
i-on16 19. Key in the number of seconds that you want the output to stay on. The maximum is 999s. 4. Administration 20. Press . The keypad gives a double “beep” confirmation tone. The keypad display shows: 25. Press to leave the menu. Note: You can switch the output on and off from the Menu by selecting Outputs On/Off (see page 85). If you want to program a remote control to control the output, see page 76.
4. Administration 21. Press until the display shows: i-on16 22. Press . The display shows the time when the output will turn off. 23 Key in the time when you want the output to go off. Use the 24-hour clock in the format hh/mm. If the hours or minutes are “9” or less then key in a leading zero. For example: six minutes past seven in the morning will be “07/06”. 24. Press .
i-on16 4. Administration the output will operate on that day, or “No” if the output will NOT operate on that day. 27. Press or to change the “Yes” to a “No” or the “No” to a “Yes”. For example: 28. Press repeatedly to show the other days of the week, for example: 29. Press or to change the the “No” to a “Yes” for each day on which you want the output to operate.
4. Administration i-on16 Programming Remote Controls for Users The System Config - Remotes option allows you to re-program buttons on an i-fb01 remote control. Set/Unset To program a remote button to set or unset: 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). 4. Press until you see:. 5. Press . 6. Press until the display shows: 7. Press . 8. Press . 9.
i-on16 4. Administration Note: You cannot reprogram the unset key on a remote control. OR (if you do not have the remote in your possession) a) Press . The display presents a list of the registered remote controls and their users. b) c) Press or to show the remote control you want to edit. Press to select it. The display shows the first button on the remote control. d) Press or to show the button you wish to reprogram.
4. Administration i-on16 c) Press . The bottom line of the display now shows the first item in a list of setting or unsetting options that you can apply to the selected button. The options available are: Part Set Part sets the system. Full Set Full set the system. Unset Unset the system. Note: Ask your Installer if the entry timer needs to be running before a user can unset using a remote. 11.
i-on16 4. Administration 3. Key in your access code (or present a tag). 4. Press until you see:. 5. Press . 6. Press until the display shows: 7. Press . 8. Press . 9. EITHER Press the button on the remote control that you wish to program. Hold the button down until you see the transmit LED flash. The display shows the identity and owner of the remote control, and the button you pressed. Go on to step 10.
4. Administration c) i-on16 Press to select it. The display shows the first button on the remote control. d) Press or to show the button you wish to reprogram. e) Press to select the button. The bottom line shows the first in a list of the options that you can assign to the button: 10. Press until the display shows: 11. Press .
i-on16 4. Administration “Off” = Turns the output off. “Toggle” = Changes the state of the output every time you press the button. 14. Press or . until the display shows the action you want to give to the button, for example: 15. Press . The keypad gives a double “beep” confirmation tone. The keypad display shows: 16. Press repeatedly to leave the menu. Repeat steps 8 to 15 if you want to program any more remotes. 17.
4. Administration 5. Press . 6. Press until the display shows: 7. Press . 8. Press until the display shows: 9. Press . The display shows: i-on16 10. EITHER a) Press the button of the remote you wish to delete: OR (if you do not have the remote to hand.) a) Press .
i-on16 4. Administration 12. Repeat steps 9 to 11 if you wish to delete any other remotes. 13. Press repeatedly to leave the menu. The control unit will let you delete all remote controls in one operation. Think carefully before you use this feature. To delete all remotes: 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). 4. Press until you see:. 5. Press . 6. Press until the display shows: 7. Press . 8.
4. Administration i-on16 11. Press repeatedly to leave the menu. To register remote controls with users once again enter the Menu and select Users - Edit User (see page 43). Preventing Any Remote From Unsetting the System You may wish to prevent any remote from unsetting your alarm system. You can do this as follows: 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). 4. Press until you see:. 5. Press . 6.
i-on16 4. Administration 12. Press repeatedly to leave the menu. Once you have carried out this process, then although remote controls can set the system, none of them can unset the system. To allow remote controls to unset the system repeat steps 1 to 12, but select “enabled” at step 10. Redirecting Speech Messages Note: This option is available only if you have the a speech dialler module fitted inside the control unit and it has been programmed by the installer.
4. Administration 8. 9. Press until the display shows the telephone number that you wish to change, for example: i-on16 Press . The display shows the current phone number, for example: 10. Key in the new phone number. If necessary, press to move the cursor left, or to move the cursor to the right. Press to remove digits to the left of the cursor. 11. Press to store the changes you have made.
i-on16 4. Administration Turning Outputs On/Off You can operate the outputs from the keypad, as well as by using a remote control (provided the installer has assigned some outputs to you). To operate an output: 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). 4. Press until you see:. 5. Press . The display shows the first in a list of the outputs that are available to you.
4. Administration i-on16 What System Have I Got? There may be times, when your installer is helping you with a problem over the phone, that they ask you what system you have and what software version it is running. You can find this information as follows. 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). 4. Press until you see: 5. Press . .
i-on16 4. Press until you see: 5. Press . 6. Press . until the display shows: 7. Press . The bottom line of the display shows the module type currently fitted (or the word “None” if no module is fitted). 8. Press repeatedly to leave the menu. 4.
i-on16 List of Menu Options Item Omit Zones Users Add User Edit User (for each user:) Name Type (not U01) Code Prox Tag Remote Hold Up Alarm Delete User View Log Test Siren & Sounders Wired Keypad Walk test Outputs Remotes User Hold Up Alarms Prox Tags System Config Facilities On/Off Chime Set Date & Time Speech Phone Book Edit Outputs Remotes Outputs On/Off About Page 88 Page 35 40 48 37 38 38 36 41 43 45 50 52 53 53 56 57 59 61 62 64 65 65 66 83 68 74 85 86
i-on16 Alarm Functions At a Glance OK Display shows: Time and date when system off (unset). First zone to alarm after alarm Read log here. NO Glowing = On (set) Off = Off (unset) Flashing = Part Set Key in access code here HUA/PA keys Hold prox tag near face of keypad. Setting and Unsetting IN ORDER TO: DO THIS: THE SYSTEM WILL: Turn the system on: EITHER: Start the exit tone. Key in ACCESS CODE and press OR present tag. Then leave the premises and close door.
i-on16 After an Alarm IN ORDER TO: DO THIS: THE SYSTEM WILL: Switch off siren: EITHER: Key in ACCESS CODE OR present tag. Stop the siren. The keypad display shows the first zone to alarm. Reset the system: Press . Keypad display shows time and date. Read the log: Press + ACCESS CODE (or tag) + 3 + . Keypad display shows most recent event. Press . Keypad display shows older events. Press . Keypad display shows newer events. For more information see page 16 .
