INSTALLATION AND PROGRAMMING GUIDE 9651 HARDWIRED CONTROL PANEL
9651 Hardwired Control Panel Installation and Programming Guide © Cooper Security Ltd. 2004 Every effort has been made to ensure that the contents of this book are correct. However, neither the authors nor Cooper Security Limited accept any liability for loss or damage caused or alleged to be caused directly or indirectly by this book. The contents of this book are subject to change without notice. Printed and published in the U.K.
Contents 1. INTRODUCTION.......................................................................................... 3 Operator Controls and Displays - 9930 ..........................................................................................................4 System Features.............................................................................................................................................5 Detectors .................................................................................
Contents 39: Level A Exit Mode.................................................................................................................................34 40: System Auto Re-Arm............................................................................................................................35 41: Bell Delay .............................................................................................................................................35 42: Bell Duration ........................
1. INTRODUCTION The 9651 control unit is designed to be fully programmable to suit individual site requirements and user needs. Note that in the UK the product does not comply with the ACPO 2000 alarm policy and DD243: 2002. The system comprises a control unit in a metal shielded case and up to four separate keypads (see Figure 1 on the next page). You should always fit at least one keypad. The control unit provides: ° A four-wire bus connection for keypads.
3. Introduction 1 - Control unit 2 - Keypads 3 - PIRs 4 - Door contacts 5 - fused mains spur Figure 1. 9651 System Layout Operator Controls and Displays - 9930 Figure 2. 9930 Remote Keypad. The 9930 keypad has a 32 character LCD display that shows "first to alarm" information, level status, and programming commands.
3. Introduction a Glows steadily when mains power is present. Flashes when the system is working from battery backup. f Glows steadily if a telephone line fault is present. s Glows steadily if: a) A fault or tamper circuit is active while the system is unset. b) The system needs an engineer or remote reset. c) A telephone line fault is present. The 9930 keypad provides the following keys: 9 Used to start a test of the detectors. 8 Used to start a test of the sounders and strobe.
2. Technical Description Specification Environmental EN50131 “Class II” Dimensions -10° to +40 °C. 75 % RH. Junior combi box: 243mm W, 234mm H, 87mm D Weight Junior combi box: 2.45 kg (without standby battery) Internal Clock ±10 minutes over one year (depending on the accuracy of the mains supply frequency). Conforms to BS4737 1986 Part 1. for Audible or Remote signalled systems. Designed to fulfil the requirements of a EN 50131-1 Grade 2 Intruder Alarm System. Power Supply All currents accurate to ±5%.
2. Technical Description Control Unit PCB Figures 3 show the layout of the 9651control unit PCB. 12V AUX F-1A 12 11 10 BATT F-2A 1 9 8 2 7 3 6 4 5 1. Outputs. 2. Aux power. 3. Tamper switch. 4. Zone connectors. 5. Keypad bus. 6. Communications Outputs. 7. NVM Reset pins. 8. Battery connector. 9. Battery fuse. 10. Kick start pins. 11. 21VAC from transformer. 12. 12V AUX fuse. Figure 3.
3. INSTALLATION Overview A typical installation comprises the following main steps: 1. Carry out a Risk Assessment of the premises and agree a security grade for the proposed alarm installation. Decide on positions for wired detectors, control unit, keypads, external and internal sounders. As part of the site survey ask the user what facilities they require . 3. Ensure that there is a suitable mains supply present at the site of the control unit. 4.
3. Installation recommended cable lengths in metres for 7/0.2 cable, assuming that you connect all items at the end of a single cable run. In real life you may be able to improve on these figures by spreading items along the cable length. 7/0.2 8-core cable Length (m) No items 1 core 2 cores on 0V and 12V.
3. Installation 1 1 2 1 1 1. Fixing hole. 2. Adjustable cam. Figure 4. Backplate of the 9930 Keypad Cooper Security recommend that you mount the keypad using No 8 or 6 screws (M4/M3.5) as follows: 1. Select which cable entry you are going to use and break out the appropriate plastic sections. 2. Hold the backplate in place against the wall and mark the position of the centre hole in the adjustable cam (see Figure 4). 3.
3. Installation Wiring the Control Unit Cable Entries The control unit case back provides several cable entries. The back is designed to stand away from the wall to leave space for cables. Mains Connection The control unit must be permanently connected to a 3A fused spur outlet fitted with a readily accessible disconnect device. Connect the mains supply to the control unit using the 3-way terminal block located in the control unit back.
3. Installation Remote Keypads Keypad Addressing The control unit is supplied with one remote keypad. If you have fitted more keypads then each one must be given a separate "address". Links LK2 to LK4 set the keypad address, as shown in Figure 6. Keypad 1 Address Keypad 2 2 2 2 3 3 3 4 4 4 Keypad 3 Keypad 4 2 2 3 3 4 4 ON BACKLIGHT ON BACKLIGHT Backlight ON ON BACKLIGHT Backlight OFF Figure 6. Keypad Addressing.
3. Installation Typical internal Sounder 16Ohm loudspeaker (2 Max in parallel) Bell Strobe Typical SAB 9651 Control Unit +ve -ve OP1 OP2 OP3 TR + LS 12V AUX 12V AUX 0V 0V Bell -ve Hold Off -ve Tamper Return +ve Hold Off -ve Apply Trig 9930 Keypad 0V 12V CLK DATA ET Lock Switch OR Exit terminate button (NO, push to make) 9651 Control Unit 0V 12V CLK DATA To other keypads 4-core Fig 7.
3. Installation FSL Connections The control unit zone connectors provide space for up to eight FSL zones. Each FSL zone is a ‘Fully Supervised Loop’ using a two wire closed loop. The loop uses two resistors of different values to differentiate between ‘Circuit’ and ‘Tamper’ signals: a 2K2 resistor fitted in series at the end of the wired loop, and a 4K7 resistor fitted across the alarm contact, see Figure 9.
3. Installation To program the outputs use programming command 81 for OP1, command 82 for OP2 and command 83 for OP3 (see "4. Programming").
3. Installation Fitting a Plug-by Communicator The 9651 can be fitted with a communicator or speech dialler, for example the Scantronic 660, 8400, and 8440 digital communicators or the SD1 or SD2 Speech diallers. To fit a communicator inside the control unit, follow the instructions below. To connect an SD1 or SD2 follow the instructions provided with those products. Caution: Follow the instructions in the order shown, or you may damage the control unit and/or communicator. 1.
3. Installation Com Connector Cable, Part No.
3. Installation Fitting a Battery Fit a rechargeable battery into the back of the case. The case provides space for a 12V 7AH battery. Make sure the battery terminals are oriented in the position shown in Figure 16. 7AH Figure 16. Fitting a Battery Initial Start Up Before applying power to the control unit, ensure that: • All remote keypads have been addressed and connected. • All external and internal sounders are connected. • All wired zone circuits are connected. Then: 1.
3. Installation The power LED on the keypad glows steadily. 6. Key-in 0 followed by the factory default engineer access code: 7890. (You do not have to remove the control unit lid.) The display shows: Installer Mode You are now in programming mode. Carry on to Chapter 4 in order to program the system.
4. Programming Entering Programming Mode Installation - Initial Power Up” describes how to enter programming mode for the first time in a new installation. If you wish to enter programming mode at any other time: 1. Make sure the system is unset. 2. Press 0, then key in the Engineer’s code (default 7890). The display shows: You are now in programming mode. Installer Mode While the system is in programming mode all keypads except the one you are using will be locked, displaying “Busy”.
4. Programming Command 0 n= Country PTT Defaults country, one of: 0 = UK (Y) 1 = Italy 2 = Spain 3 = Portugal 4 = Netherlands 5 = France 6 = Belgium 7 = Germany 8 = Switzerland 9 = Austria X1 = Ireland X2 = OEM 1 X3 = OEM 2 X4 = OEM 3 X5 = Norway X6 = Denmark X7 = Sweden Note: If you carry out this Command then the system will load all defaults for the selected country.
4. Programming 41 42 43 44 45 46 Bell Delay 0 No delay 1 1.5 minutes 2 3 minutes 3 5 minutes 4 10 minutes 5 15 minutes 6 20 minutes 41YnY Y Bell Duration 1 1.
4. Programming 78 79 81 Level D Entry Time 1 10 seconds 2 20 seconds 3 30 seconds 4 45 seconds 5 60 seconds 6 120 seconds 78YnY Level D Exit Time 1 10 Seconds 2 20 seconds 3 30 seconds 4 45 seconds 5 60 seconds 6 120 seconds 79YnY Output 1 Type, one of 81YnY Output 2 Type, one of See Command 81 for a list of options. Default for Command 82 is 08 Strobe. 82YnY 83 Output 3 Type, one of See Command 81 for a list of options. Default for Command 83 is 03 Set latch.
4. Programming 157 Plug by Comms Output 7 Not used. See Command 151 157YnnY 158 Plug by Comms Output 8 Default 06 Technical.
4. Programming Re-entering Programming Mode You can go back into programming mode whenever the system is unset and not in alarm: 1. Key in 0 followed by the Engineer’s code (default 7890). The display shows: You are now in programming mode. Installer Mode Restoring the Access Codes (1st stage reset) If the user and/or engineer codes are lost, then: 1. First remove mains power and then open the case and disconnect the battery. 2.
4. Programming Programming Command Reference 0: Country Defaults Use this Command to select the country and PTT defaults (to select language see Command 126). Note: 1. If you select options X5, X6 or X7 (Norway, Sweden or Denmark) then the control unit also changes the method of entering programming mode. See “Entering Programming Mode” at the beginning of this chapter. 2. This Command loads default access codes and programming options. See “Programming Commands” for details of the options available.
4. Programming Figure 17. Letters Generated by Each Number Key Zone Types The following types are available: 00 Not Used (NU) The system ignores Zones with this type. Key in 00 for a zone that will not be used. Note: If a zone is programmed as ‘Not Used’, it is not necessary to link the circuit or anti-tamper connections.
4. Programming 06 07 08 Entry Route (ER) - Use this zone type for detectors sited between the Final Exit door/detector and a keypad. If an ‘Entry Route’ zone is violated when the system is set, an alarm will occur. If the entry/exit timer is running when an Entry Route zone is violated then no alarm occurs until the entry/exit timer expires. Shock Analyser (SA) - You can apply this zone type to zones 1 to 4 Only.
4. Programming To set Level A do not assign a Keyswitch zone to levels B, C or D. To set any other level assign the Keyswitch zone to a single level. 11 Momentary (KM) - Use this zone type to connect a momentary keyswitch to a single zone. 12 Fixed (KF) - Use this zone type to connect a fixed position keyswitch to a single zone. 13 Anti-Mask Zone (AM) - Note This zone type is for use in EN50131 Grade 3 systems only and is not applicable on the 9651 control panel.
4. Programming X3 Double Knock (2) Zones with this attribute will cause an alarm condition only if one or more sensors generate two alarms events within a five minute time window, or if one zone remains open for more than 10 seconds. Programming a zone as ‘Double Knock’ is a way of reducing false alarms caused by environmental changes, but is not normally recommended. Note: ‘Double Knock’ is available only for Normal Alarm and Entry Route zone types.
4. Programming 21: Zone Configuration This Command allows you to select the wiring type of the zone connectors on the main PCB. The options available are: Option 0 Eight Closed circuit zones with global anti tamper on control unit. 1 Eight Fully Supervised Loop (FSL) zones on control panel. See Chapter 3 for wiring details. 22: Loudspeaker Chime A user may find that the chime tone from the keypads is not loud enough.
4. Programming 28: Status Display Use option 1 of this Command if you do not wish to show keypad displays permanently. The keypad displays “Level Set” for 180 seconds after the user sets the system and then reverts back to the time and date display. Use this option when installing a system in the U.K. When set to option 0 the keypad displays “Level Set” the whole time that the alarm system is set. Use option 2 to make the keypad display revert to time and date 30 seconds after any event.
4. Programming 33: System Reset If you wish to make the system engineer reset, then use option 1. For user reset use option 0. Certain types of event will always need an Engineer reset, no matter what option you choose for Command 33. These events are: Auxilliary 12V supply fuse blown. Keypad missing or failed. A low battery at the control unit. 34: PA Reset If you wish to make the system engineer reset after a PA alarm then use option 1. For user reset use option 0.
4. Programming 38: System Tamper Reset This Command allows you to choose whether the customer can reset the system after a tamper alarm. This facility is independent of that offered by Commands 31 and 33. If you select option 0 (customer) then the user can reset the system after a system tamper alarm providing no fault exists. If you select option 1 (engineer) then you must enter the engineer access code at a keypad to reset the system after a system tamper alarm.
4. Programming the entry timer. The user completes entry by unsetting the system in the normal way. Note: If an intruder opens the final exit door without first unlocking the lockswitch then the control unit immediately starts an alarm. If you select Timed (options 0), Terminate (option 1), or Final Door (option 2) exit modes the system allows a seven second settling time after pressing an exit terminate button or closing a final door.
4. Programming tones, while option 9 gives the loudest entry/exit tones. The internal sounder demonstrates the volume of the tone when you enter the digit. 46: Tamper Alarm Annunciation Use this Command to chose which sounders the control unit will activate for a tamper alarm while the system is unset. Option 0 Selects internal sounders only. 1 Selects keypad sounders only. 2 Selects internal sounders and keypad sounders.
4. Programming 4. 5. Key in the two digits for the month number and press Y . Use a leading zero for January to September. Key in the two digits of the year and press Y. The display shows the current time, for example: 6. 7. H09 M15 Key in two digits for the hours of the day and press Y. Use the 24-hour clock. Key in two digits for the minutes and press Y. The keypad sounder gives a double “bleep” and the display shows “Installer Mode”.
4. Programming to 1 any Entry Route zones included in part set B will act as Final Exit zones during part set B. 62: Level B Exit Mode Command 62 specifies the exit mode for Level B. Option 0 Low Tone. Timed set with the exit tone fixed at half volume.Use Command 65 to select the exit time. 1 Instant Set (no exit tone) 2 Silent Set. (Timed Set with no exit tone) .Use Command 65 to program the Exit time. 3 As A. The exit mode chosen for Level A (whole system) is also applied to this level.
4. Programming 71: Level C Entry Route Operation Command 71 controls how the system treats Entry Route zones during part set Level C. When the option is set to 0 all Entry Route zones included in part set Level C will continue to act as Entry Routes during part set Level C. When the option is set to 1 any Entry Route zones included in part set Level C will act as Final Exit zones during part set C. 72: Level C Exit Mode Command 72 specifies the exit mode for Level C. Option 0 Low Tone.
4. Programming 0 Low Tone. Timed set with the exit tone fixed at half volume. Use Command 79 to select the exit time. 1 Instant Set (no exit tone) 2 Silent Set. (Timed Set with no exit tone ).Use Command 79 to program the Exit time. 3 As A. The exit mode chosen for Level A (whole system) is also applied to this level. Note: That the keypads give a double beep confirmation tone at the end of all setting modes. 77: Level D Alarm Response Command 77 specifies the alarm response for Level D.
4. Programming Output Type Option 00 Bell. - The control unit operates this output during an alarm. Use Command 41 to control bell delay and 42 to control bell duration. 01 EE Follow. - This output is active when the entry or exit time starts and deactivates at the end of the entry/exit time, or if the entry/exit time is terminated. The output can be used for a separate entry/exit buzzer. Note that the output does not give a tone during part set if the exit mode is silent set or instant set.
4. Programming output for 3 seconds when the system is reset after any alarm has occurred. 10 Siren Test. - This output becomes active when the Installer performs a sounder test using Command 91. 11 Strobe Set. - This output is active for 10 seconds after the system has set. The output can be used to operate the strobe to give a visual indication that the system has completed setting. 12 Pulse Set o/p 1.
4. Programming 33 Pulse Unset o/p 4. - This output becomes active for a programmable time period between 1 – 12 seconds (command 172) when someone unsets the A or B or C or D levels, or during a fire or PA alarm (if the function is selected in commands 174 or 175). 85: Burglar Communications Re-arm This Command determines what happens to the “Burg” communications output at the end of the bell run time. Option 0 Latched. The output stays active until an engineer or user resets the system. 1 Rearm.
4. Programming 90 - 97: See “5.Testing” 98: Load Full Defaults Use this Command to load default values for all Commands. 1. Enter programming mode (if you are not already there). 2. Key in 98 Y at the keypad. The display shows: 3. 4. Load default Press 1. (You can press X to stop the procedure if you change your mind at this stage.) Press Y. The keypad gives a double confirmation tone and the system loads the factory default Command values, erasing all previously programmed values.
4. Programming 126: Select Language The control unit can display messages on the keypads in one of several different languages. Use Command 126 to select the language you wish to use.
4. Programming 1 +ve Applied to trigger. The inactive output floats. When active the output goes +ve. 170 - 175: Pulsed Set & Unset Output Options Use commands 170 to 175 to apply additional options to the output types pulsed set o/p 1-4 and pulsed unset o/p 1-4. Example 1: Panel output 3 is programmed with the output type 12 (Pulsed set o/p 1). This is required to operate a locking mechanism when the system is set.
4. Programming 172 173 174 175 Set o/p 3 ABCD, select the level(s) in which the output will be active toggle abcd keys to select level on /off. Set o/p 4 ABCD, select the level(s) in which the output will be active toggle abcd keys to select level on /off.
5. Testing Reading the Log (Command 90) The control unit keeps a log of recent events The log can contain up to 250 events. Each event is represented by a short text message, shown below and on the next page. To review the event log, make sure the system is in programming mode, then: 1. Key in 90Y. The display shows the most recent event in the log. For a list of the log messages see below. 2. Key in 1 to show earlier events or 3 to see more recent events. 3.
5.
5. Testing Testing Outputs (Commands 91-96) You may test parts of the system by entering commands at the keypad. To carry out a test make sure the system is in programming mode and then key in one of the following commands. Press Y to end each test: 91Y To test output 1 (usually the external sounder/bell). 92Y To test output 2 (usually the strobe output). 93Y To test output 3. 95Y To test the keypad sounder. Engineer Walk Test (Command 97) Allows the engineer to test all devices on the system. 1.
Index 24 hour alarm............................................................. 41 24 hour zones ............................................................ 27 Access codes ............................................................... 5 restoring ................................................................ 25 Alarm Abort description ............................................................. 33 Alarm response Level B .................................................................. 38 Level C ...
using ......................................................................14 PA reset......................................................................33 Panic Alarm ................................................................27 PCB ..............................................................................7 Plug by communicator outputs ...................................45 Power Control unit current ..................................................6 Programming commands ......................
Notes 496929 Page 53
Declaration of Conformance Cooper Security Ltd issues this certificate to certify that the equipment known as: 9651 Complies with the following directive: 1995/5/EC R&TTE Directive Signed Stewart Taylor, Technical Director Date: 6/2/2004 Cooper Security Ltd. Security House Vantage Point Business Village Mitcheldean Gloucestershire GL17 0SZ www.scantronic.co.uk Product Support (UK) Tel: +44 (0) 870 757 5400. Available between: 08:15 and 17:00 Monday to Thursday, 08:15 and 12:45 Friday.
