9x5x PROGRAMMING GUIDE HARDWIRED CONTROL UNITS
9853, 9752, 9751 Hardwired Control Unit Programming Guide This document applies to control panels using software version 4.2.x. © Cooper Security Ltd. 2005 Every effort has been made to ensure that the contents of this book are correct. However, neither the authors nor Cooper Security Limited accept any liability for loss or damage caused or alleged to be caused directly or indirectly by this book. The contents of this book are subject to change without notice. Printed and published in the UK.
Contents 1. INTRODUCTION.......................................................................................... 1 About this Manual...........................................................................................................................................1 Compliance with Standards............................................................................................................................1 Operating Modes ......................................................................
Contents 61: Level B Entry Route Operation.............................................................................................................29 62: Level/Partition B Exit Mode ..................................................................................................................29 63: Level/Partition B Alarm Response........................................................................................................30 64: Not used .....................................................
Contents 132: Send Tampers as Burglary.................................................................................................................53 133: Do not Send SIA Restores .................................................................................................................54 134: AC Fail User/Installer Reset ...............................................................................................................54 135: Line Fault User/Installer Reset ...........................
Contents List of Figures Figure 1. Sensitive Area on 9930 Keypad for Tag .........................................................................................5 Figure 2. Sample Log Print...........................................................................................................................70 Figure 3. Using a Common Area ..................................................................................................................78 Figure 4. Using a Private Door .................
1. INTRODUCTION About this Manual This manual is divided into five chapters: 1. Introduction provides an overview of how to program a 9x5x control unit. 2. Programming Commands lists and describes the commands available to program aspects of a 9x5x control unit's operation. 3. Testing Commands lists and describes the commands available to test a newly installed alarm system based on a 9x5x control unit. 4.
1. Introduction Operating Modes The alarm system has three basic modes of operation that provide access to commands appropriate to different types of users: 1. User mode allows setting, unsetting and resetting of the system, along with some basic commands. There may be many user codes of this type. 2. Master user mode provides access to all user commands, including those available in user mode. The master user can configure other users. There is only one user code of this type. 3.
1. Introduction Using Programming and Testing Commands When delivered from the factory, the control unit already has default settings. To change the default settings: 1. Enter installer mode. 2. Key in the appropriate command number and press y. The display shows the current value of the command. 3. Key in digits to select the value you require. The display shows the new value. 4. Press y to store the new value of the command. Note: If at any time you change your mind, repeat steps 1 to 3.
1. Introduction To restore all access codes to their default settings: 1. Remove mains power. 2. Open the case and disconnect the battery. 3. Identify the NVM Reset pins and Kick Start pins on the main PCB (refer to the 9x5x Installation Guide). 4. Short circuit the NVM Reset pins with a wire link. 5. Short circuit the Kick Start pins with a wire link. 6. Reconnect the battery. 7. Remove the wire links from the NVM Reset pins and Kick Start pins.
1. Introduction Adding and Deleting Tags You can use any industry-standard ISO tag or card with the 934 module. To purchase tags from Cooper Security, quote part number Proxtagpk5. A tag acts as an alternative to a user access code. You can assign a user a tag, an access code, or both. You cannot assign a tag to the Master User (User 01), the Installer (User 00) or, if the Guard Code facility has been enabled using Command 181, the Guard (User 50).
1. Introduction To Add a Tag 1. 2. Key in User 01 access code while the system is unset. The display shows: Press 4 to select the change codes option. The display shows: Select? Old Code= 3. Enter the access code of the user for whom you want to program a tag and press y. The display shows the user number and any text description you have programmed for that user. 4. Press y. The display shows the user number and an underscore, User 06 = for example: 5.
2. PROGRAMMING COMMANDS 0: Country PTT Defaults Use this command to select the country and PTT defaults; it also loads default access codes and programming options. Use Command 126 to select language without making other changes. Note: If you select options X4, X5, X6 or X7 (Finland, Norway, Sweden or Denmark), the control unit changes the method of entering installer mode (see "Entering Installer Mode" on page 1).
2. Programming Commands Enter letters from the keypad one at a time by repeatedly pressing a number key until the display shows the letter you want. If you make a mistake, press C or D to move the cursor to the letter you want to change and key in the new letter. To delete a name completely, press D to move the cursor onto the first character of the name and then press D again to clear the old name. When you have finished entering the name, press y.
2. Programming Commands Value 05 06 07 08 09 10 Type Description Final Exit (FE) Zones of this type must be the first to be activated on entry. You can use them to set the system using the Final Door Set exit mode. Use Command 39 to set the exit mode for the zone (page 20). Use zone attribute X7 to select an entry timer for the zone (page 12) and Commands 201–4 (page 66) to set up the entry timers.
2. Programming Commands Value 11/12 Type Keyswitch 13 Anti-Mask Zone (AM) 14 Forbikobler (FB) 15 AC Fail (AC) 16 Low Battery (LB) Page 10 Description There are two Keyswitch zone types: Momentary and Fixed.
2. Programming Commands Value 17 Type Battery Fault (BF) 18 Power Output Failure (PF) 19 Fault (FL) Description This zone type is triggered by a fault in the battery in the external power supply. In a partitioned system, BF zones are always allocated to Partition A. This zone type is triggered by a failure in the DC output to the external power supply. In a partitioned system, PF zones are always allocated to Partition A.
2. Programming Commands Value Attribute Valid for X3 Double Knock (D) Normal Alarm (NA) Entry Route (ER) X4 X7 A B C D Page 12 Description For zones with this attribute, no action is taken on first activation. To cause an alarm, the zone must be activated twice within a fiveminute period or remain open for longer than 10 seconds. An alarm will also occur if another double-knock zone in any partition is activated within five minutes of the first.
2. Programming Commands For information on how zones behave in linked partitions, refer to "Common Areas" on page 78. Zones and Partitions In a partitioned system, you can assign some zone types to two or more partitions, and some zone types to one partition only.
2. Programming Commands 21: Zone Configuration This command enables you to select the wiring type of the zone connectors on the control unit PCB. The default is option 0 for all models. Zones type on 9751/2 PCB 0 Up to 8 closed circuit loop zones (CC + Com A/T). 1 Up to 8 fully-supervised loop zones (FSL 2K2/4K7). Zones type on 9853 PCB 0 Up to 8 closed circuit loop zones (CC 4 wire). 1 Up to 8 end-of-line zones (EOL 2K2). 2 Up to 16 fully-supervised loop zones (FSL 2K2/4K7).
2. Programming Commands 23: Remote Reset Enable Option 1 enables Remote Reset, which is designed to operate with the plugby communicator or remote PC reset. After an alarm, the user keys in an access code to silence the alarm but cannot reset the system. The first alarm message to display and the Service lamp remain visible. The user contacts the Alarm Receiving Centre (ARC), which verifies the user's identity and then sends a signal to the control unit.
2. Programming Commands 27: Exit Fault External Sounder This command controls what happens when an exit timer completes and a zone is still violated (for example, when a door is not shut). Option 0 Internal (default). System operates the internal sounders only. 1 Local. System operates both internal and external sounders. Note: Compliance with PD 6662 / prEN 50131-1: 2004 (see page 85) prohibits an alarm after a failure to set the system, which would require Command 27 to be set to option 0.
2. Programming Commands 29: Entry Alarm Delay Time This command determines what the system does if a user strays from an Entry Route zone during entry. If you select option 0 (the default), the system gives an immediate alarm when the user strays from an Entry Route zone during entry. If you select option 1, the system gives an internal alarm when the user strays from an Entry Route zone during entry but waits for 30 seconds before raising a full alarm.
2. Programming Commands 33: System User/Engineer Reset To require an engineer reset, select option 1. To permit a user reset, select option 0 (the default). Certain types of events always need an engineer reset, irrespective of the option that you choose here: ° Auxiliary 12V supply fuse blown ° Keypad missing or failed ° Remote expander missing or failed ° A low battery at the control unit. Note: Compliance with DD 243: 2004 (see page 83) requires that Command 33 is set to option 1.
2. Programming Commands 37: Daytime Tamper Communication This command defines how the control unit reports tamper indications (for example, an attempt to open a control unit or keypad case) while the alarm system is unset. Option 0 Internal sounder only (default). 1 Internal sounder and communication of tamper indication to the Alarm Receiving Centre (ARC). Notes: 1.
2. Programming Commands 39: Level/Partition A Exit Mode Use this command to select the exit mode for Full Set or Partition A. The keypads give a double "beep" confirmation tone at the end of all setting modes, including Silent Set. The default is option 0, Timed. In a single system, the options are: Option 0 Timed. Use this option if the system sets after an exit time selected using Command 44. If an Exit Terminate button is fitted, the user may use it to shorten the exit time. 1 Terminated.
2. Programming Commands Notes on Lock Set: 1. Do not assign the keypad to more than one partition. Do not connect more than one lock switch (or any other device) to the keypad ET terminals. In a single system, do not attempt to fit two lock switches. 2. To set the system, the user first enters their access code at a keypad or operates a keyswitch. The control unit starts to emit the exit tone. The exit time is infinite in this option.
2. Programming Commands 41: Bell Delay When an alarm occurs (for example, an intruder violates a zone), the system waits for the Bell Delay before operating the external sounder for the Bell Duration. This command sets the Bell Delay. Note: Compliance with PD 6662 / prEN 50131-1: 2004 (see page 85) requires that the Bell Delay does not exceed 10 minutes and that it is not used for entry alarms (see Command 26). Option 0 No delay (default) 1 1.
2. Programming Commands 44: Level/Partition A Exit Time This command lets you set the Exit Time for Full Set or Partition A. Option 1 10 seconds 2 20 seconds (default) 3 30 seconds 4 45 seconds 5 60 seconds 6 120 seconds 45: Entry/Exit Tone Volume In a single system, this command sets the volume of the Entry/Exit tone from the internal sounder. If you select option 0, the internal sounder emits no tone. Select a value from 1 (quietest) to 9 (loudest) to set the volume (default 5).
2. Programming Commands 48: Lockout Keypads During Entry This command enables you to lock keypads during entry when proximity tag readers or remote setting devices are being used to unset the system. When you lock keypads during entry, some functions are still available: ° Keypad PA, Fire and Medical alarms ° Duress Code operation ° User's ability to cancel false alarms or disarm the system during an alarm. If you select option 0, the system permits all users to use all keypads during entry.
2. Programming Commands 50: CSID Code To enable the user to use the "Remote Reset" facility (enabled with Command 23), you must program the control unit as "Engineer Reset" (Command 33 option 1) and install a four-digit Central Station Identification (CSID) code: 1. Contact the Alarm Receiving Centre (ARC) and obtain the CSID code. 2. Ensure that the system is in installer mode. 3. Select Command 50 and enter the four-digit CSID code.
2. Programming Commands 54: Supervision Time Radio zones are supervised. If they do not communicate for a certain time, the control unit reacts in the way selected with Command 55. The time is based on the supervision period of the radio detector used in the zone, which depends on the model as shown in the following table. The model number is usually shown on a label affixed to the PCB inside the detector.
2. Programming Commands 55: Supervision Response This command specifies how the control unit responds to a reported supervision failure (as described in Command 54). Option 0 Supervision response: tamper (default) 1 Supervision response: alarm 2 Supervision response: fault 3 Supervision response: silent Note: Compliance with PD 6662 / prEN 50131-1: 2004 Grades 1 and 2 (see page 85) requires option 0. Grade 3 does not permit radio zones.
2. Programming Commands 56: Number of Digits in Access Codes The control unit can use either four-digit or six-digit access codes. Select option 0 for four-digit access codes and option 1 for six-digit access codes. Changing code length causes the system to revert to factory defaults for all access codes; four-digit defaults are 1234 (user) and 7890 (engineer), sixdigit defaults are 123456 (user) and 567890 (engineer).
2. Programming Commands 60: Level B Final Exit Operation In a single system, this command specifies how the system treats Final Exit zones during part set B. If you select option 0 (the default), Final Exit zones included in Level B continue to act as Final Exit zones during part set B. If you select option 1, these zones act as Normal Alarm zones during part set B. Note: This command is not available in a partitioned system.
2. Programming Commands In a partitioned system, the options are: Option 0 Timed. Use this option if Partition B sets after an exit time selected using Command 65. If an Exit Terminate button is fitted, the user may use it to shorten the exit time. 1 Terminate. Use this option if the user completes setting the partition by pushing an Exit Terminate button connected to a keypad. The exit time is infinite in this option. 2 Final Door Set.
2. Programming Commands 65: Level/Partition B Exit Time This command sets the Exit Time for Level or Partition B. Option 1 10 seconds 2 20 seconds (default) 3 30 seconds 4 45 seconds 5 60 seconds 6 120 seconds 66: Forbikobler Keypads and Partitions If you created a partitioned system during initial power up, this command enables you to assign individual Forbikobler keypads to those partitions. By default, all Forbikobler keypads belong to all partitions.
2. Programming Commands 69: Forbikobler Door Locking This command specifies whether the door controlled by the Forbikobler system is normally unlocked while the system is reset or opened only for a controlled time. Even if the door is normally unlocked, it can be locked with a user command if required. Option 0 Lock Timed (default) 1 Lock Toggled 70: Level C Final Exit Operation In a single system, this command specifies how the system treats Final Exit zones during part set C.
2. Programming Commands In a partitioned system, the options are: Option 0 Timed. Use this option if Partition C sets after an exit time selected using Command 75. If an Exit Terminate button is fitted, the user may use it to shorten the exit time. 1 Terminate. Use this option if the user completes setting the partition by pushing an Exit Terminate button connected to a keypad. The exit time is infinite in this option. 2 Final Door Set.
2. Programming Commands 75: Level/Partition C Exit Time This command sets the Exit Time for Level or Partition C. Option 1 10 seconds 2 20 seconds (default) 3 30 seconds 4 45 seconds 5 60 seconds 6 120 seconds 76: Level/Partition D Exit Mode This command sets the Exit Mode for Level or Partition D. The keypads give a double "beep" confirmation tone at the end of all setting modes, including Silent Set. The default is option 0, Timed. In a single system, the options are: Option 0 Timed.
2. Programming Commands 77: Level/Partition D Alarm Response This command sets the Alarm Response for Level or Partition D. In a single system, the options are: Option 0 Keypad sounders only. 1 Internal sounders and keypad sounders (default). 2 Local alarm (internal and external sounder only). 3 Full alarm (communication and internal/external sounders). In a partitioned system, the options are: Option 0 Keypad sounders only. 1 Local alarm (internal and external sounder only).
2. Programming Commands 81 to 84: Output n Type These commands, along with Commands 215 to 218, select types for the control unit's panel outputs.
2. Programming Commands 05 Walk Test: active during both engineer and user Walk Tests and during the time between silencing and resetting the system. It is used on movement detectors that are able to switch off the Walk Test lamp in any state other than a Walk Test. 06 Ready Lamp: active when the system is unset and if there are no faults. It is inactive when the system is full or part set, during any alarm or if a circuit fault prevents setting.
2. Programming Commands 26 Pulse Set 1: active for time set by Command 170. 27 Pulse Set 2: active for time set by Command 170. 28 Pulse Set 3: active for time set by Command 170. 29 Pulse Set 4: active for time set by Command 170. 30 Pulse Unset 1: active for time set by Command 172. 31 Pulse Unset 2: active for time set by Command 172. 32 Pulse Unset 3: active for time set by Command 172. 33 Pulse Unset 4: active for time set by Command 172. 34 Fire: active during a Fire alarm.
2. Programming Commands 87: Keypad Dual Key Alarms This command enables users to raise an alarm by pressing two keys on the keypad at the same time. Three types of alarms are available, each of which can be enabled or disabled independently. The default is disabled (option 0). Alarm type PA Medical Fire Key combination 1 and 3 4 and 6 7 and 9 Disable 0 0 0 Enable 1 1 1 Press A and B to scroll up and down through the types (PA, FI and MD). Notes: 1.
2. Programming Commands Option 0 Masking (default). Resistance values of both 4.4kΩ and 9.1kΩ are reported as Masking detected. 1 Masking and Fault. A resistance value of 4.4kΩ is reported as a Fault and 9.1kΩ is reported as Masking detected. Note: 1. Using three-resistor anti-mask wiring requires that Command 21 is set to one of the Fully Supervised Loop options (2 or 3). 2.
2. Programming Commands 99: Leave Installer Mode This command returns to user mode (for more information, see page 3). 100: Not used This command is not used. 101: Call Mode Use this command to select the call mode used by the communicator when contacting the Alarm Receiving Centre (ARC). Option 0 Disabled (default). The control unit does not use any communications. 1 Single reporting. The control unit reports to one programmed telephone number (see Command 115) with one account number (see Command 117).
2. Programming Commands 102: Communication Fault Timeout This command sets the period after which a communications fault times out. In earlier versions of the 9x5x series, timeouts occurred after a specified number of calls. Option 0 60 seconds 1 120 seconds 2 240 seconds (default) 3 480 seconds Note: Compliance with PD 6662 / prEN 50131-1: 2004 (see page 85) requires that Command 102 is set to option 2.
2. Programming Commands 105: Static Test Call With static testing, the control unit makes test calls at fixed times or intervals; alternatively, you can use Command 108 (see page 44) to set up a dynamic test call for 24 hours after the last communication. Note: Cooper Security recommends that you choose either Static Test Call (105) or Dynamic Test Call (108), but not both at the same time. To disable static test calls, key in "00".
2. Programming Commands 106: Line Fault Response This command sets how the control unit responds when it detects a fault on an attached telephone line. The response depends on whether the system is set or unset. Option 0 Disabled. The control unit does not monitor the telephone line. 1 Audible (default). If the system is unset, the control unit logs the event and the keypads emit a short audible tone every minute.
2. Programming Commands 109: Three-way Calling (UK only) To use three-way calling, you must make sure that the BT Network Services Option of "three-way calling" is available on the telephone line to which the communicator is connected. Option 0 Three-way calling off (default). 1 Three-way calling on. Operation: If the communicator, when triggered by the control unit, detects Off Hook or Incoming Ringing, it sends an 80ms trigger.
2. Programming Commands 112: Rings to Answer Use this command to set the number of rings for which the system waits before answering an incoming call from the remote PC. Option 0 3 rings 1 5 rings (default) 2 7 rings 3 10 rings 4 15 rings 5 255 rings 113: Answer on One Ring If the alarm system shares a telephone line with other equipment, use this command to instruct the control unit how to interpret one ring on the shared line. Option 0 One Ring off (default).
2. Programming Commands 114: Access Mode You may wish to impose extra security on communication between a remote PC and the control unit as, once the PC is connected, Downloader has access to all programming commands. Select option 0 (the default) to require the user to initiate communication with the remote PC. Select option 1 to accept remote calls but check the details sent by the Downloader software. Select option 2 if you do not require extra security. Option 0 Callback off (Attended).
2. Programming Commands 117: Account Number With SIA formats, the control unit can report alarms using a six-digit account number. Use leading zeros to pad the account number to the correct length if necessary; for example; account 1234 would be 001234. Some European countries use letters in account numbers. The control unit accepts B, C, D, E and F ("Zone Names" on page 7 explains how to enter characters). In a partitioned system, you can enter up to four account numbers, one for each partition.
2. Programming Commands 122: Communication Acknowledge This command is available only if Country is set to Ireland (Command 0, option X1). In addition, option 1 is effective only if Scancom Fast Format is selected (Command 103, option 0). To enable Communication Acknowledge, select option 1.
2. Programming Commands 126: Select Language The control unit can display messages on the keypads in several languages. Select option for the language you wish to use: 0 1 2 3 4 5 English (default) Italian Espanol (Spanish) Port (Portuguese) Nederl (Dutch) Francai (French) 6 7 8 9 X1 Deutsch (German) Norsk (Norwegian) Svenska (Swedish) Dansk (Danish) Suomi (Finnish) Note: This overrides the default language loaded when the Country is selected with Command 0. 127: Not used This command is not used.
2. Programming Commands 131: SIA Report Mode SIA reports are called telegrams. Each telegram contains the site identification number (normally six digits) and relevant event information. The amount of information reported depends on the SIA mode that you select: Basic, Summary, Intermediate or Full. The following table shows the types of report for each mode; use this to decide which mode is appropriate for the installation. Each mode also contains all the reports in the mode above it.
2.
2. Programming Commands KEYSWITCH DISARM KEYSWITCH ARM FULL Event DOWNLOAD SUCCESS EXPANDER MISSING EXPANDER MISSING RESTORE FORBI MISSING FORBI MISSING RESTORE JAMMING PASSWORD DEFAULTS LOADED PROG MODE START PROG MODE END TD (Time and day) RESET TX BATTERY TROUBLE USER CODE CHANGED USER CODE DELETED OS CS 409 409 SIA Code RS TA TR TA TR XQ RH LB LS JT XT JV JX CID Code 412 137 137‡ 137 137‡ 380 627 628 625 384 - Notes: 1. If Command 143, option 1 is selected, all messages with a CID Code are sent.
2. Programming Commands 133: Do not Send SIA Restores Use this command to stop the system sending SIA restore messages. Option 0 SIA Restores Off (default). System does not send SIA restore messages: FR (Fire Restore), PR (Panic Restore), UR (Technical Restore), BR (Burglary Restore) or TR (Tamper Restore). 1 SIA Restores On. System sends SIA restore messages. 134: AC Fail User/Installer Reset Use this command to determine how AC Fail alerts are reset. Option 0 No Reset Required (default).
2. Programming Commands 137: AC Fail Override Use this command to determine how AC Fail alerts can be overridden. Option 0 Never. The user cannot override AC Fail alerts when setting the system and must first reset them. Command 134 determines how the alert can be reset. 1 Inactive. The user can override AC Fail alerts when setting the system, provided that the power supply has been restored. 2 Any (default). The user can override AC Fail alerts when setting the system.
2. Programming Commands 139: Fault User/Installer Reset Use this command to determine how alerts can be reset for all faults that do not have an individual reset command. Option 0 User Reset (default). Fault alerts can be reset by the user or installer. 1 Installer Reset. Fault alerts can be cleared only by the installer. Notes: 1.
2. Programming Commands 143: Contact ID Report Restores If the Reporting Type is set to Contact ID (Command 103, option 1), use this command to select the types of contact ID messages that will be sent. Option 0 Basic: all the messages with numbers in the "CID Code" column of the table in "131: SIA Report Mode", except for those marked with an "‡". 1 Basic + Restore (default): all the messages with numbers in the "CID Code" column of the table in "131: SIA Report Mode".
2.
2. Programming Commands 159: Invert Plug-by Outputs By default, plug-by outputs have a positive voltage when inactive and this is removed when the output is active. This command inverts that logic so that a positive voltage is applied when the output is active. Option 0 +ve removed to trigger (default): the output is positive when inactive and goes to zero when active. 1 +ve applied to trigger: the output floats when inactive and goes positive when active.
2. Programming Commands 162: External Sounder on Confirmed or Unconfirmed Alarm Note: Set Alarm Confirmation (Command 89) to 1 or 2 to access this command. This command selects whether the control unit will operate the external sounder for a confirmed alarm or for an unconfirmed alarm. Option 0 Control unit operates the external sounder for a confirmed or unconfirmed alarm (default). 1 Control unit operates the external sounder only for a confirmed alarm.
2. Programming Commands 164: User/Engineer Reset after Confirmed Alarm Note: Set Alarm Confirmation (Command 89) to 1 or 2 and Enable Engineer Reset (Command 33) to access this command. Use this command to select who can reset the system after a confirmed alarm. Option 0 User/Engineer (default). The user can reset the system after a first alarm but an engineer is required to reset after a confirmed alarm. 1 User/User. The user can reset the system after both types of alarm. 2 Engineer/Engineer.
2. Programming Commands Notes: 1. Generating a pulse on an output depends both on a set or unset pulse being defined for the output and on the output being associated with a partition that is being armed or disarmed. 2. Commands 174 (Fire) and 175 (PA) activate only the Pulse Unset outputs configured with Command 172. Example 1 In a single system, panel output 3 is to be programmed as type 12 (Pulse Set 1). It will be used to operate a locking mechanism when the whole system is set.
2. Programming Commands 180: Print Log (9853 only) This command instructs the control unit to print the event log through the serial port on the main PCB. Selecting option 1 causes events to be printed as they occur until the mode is cancelled by selecting option 0. To print the log during testing, use Command 90, options 0 and 7, as described on page 70. Option 0 Off (default). Do not print the event log. 1 On. Print the event log.
2. Programming Commands 185: Keyswitch Auto Reset This command instructs the control unit to reset automatically if the user uses the keyswitch to set the system on leaving. Option 0 Off (default). User must reset manually. 1 On. System resets automatically when the user sets it with a keyswitch (KM or KF). Note: Compliance with PD 6662 / prEN 50131-1: 2004 (see page 85) requires that Command 185 is set to option 0.
2.
2. Programming Commands 200: Forbikobler Entry Timer This command sets the interval between a user entering the premises through a Forbikobler entrance and an alarm going off, using one of the independent entry timers configured with Commands 201 to 204. Any of the entry timers can be assigned to any Forbikobler entrance. Entering the entry code into the Forbikobler unit starts the selected entry timer.
2. Programming Commands Setting Different Entry Timers for Different Entrances Suppose that you have installed a system on a site that can be entered through a front door or through an integral garage with an internal door: ° When a user opens the front door, it may take only 20 seconds to step inside and enter an access code at a keypad in the lobby.
2. Programming Commands 211 to 214: Plug-by Communicator Outputs These commands select types for the four additional programmable outputs on the optional expansion for the 9853. For details, see Commands 151 to 158 on page 57. 215 to 218: Output n Type These commands select types for the control unit's panel outputs. They apply only to the 9853, as only it has eight outputs. For details, see Commands 81 to 84 on page 36.
3. TESTING COMMANDS 90: Reading the Event Log The control unit keeps a log of recent events. The log can contain up to 700 events. Each event is described by a short text message. To review the event log, make sure the system is in installer mode and then: 1. Key in 90y. The display shows the most recent event in the log. 2. Key in 1 to show earlier events or 3 to show later events. 3. Key in 4 to show the first event or 6 to show the last event. 4. Press X to leave the log.
3. Testing Commands Printing the Event Log (9853 only) Note: 975x models do not have the connector required for event log printing. To print the event log, make sure the system is in installer mode, and then press 90y0. To stop printing, press X. To toggle the logging printer on and off, press 90y7. The keypad gives a Chime tone when the printer is turned on and a "beep beep" confirmation tone when the printer is turned off. This is a test mode and is cancelled if power is lost.
3. Testing Commands Keypad Display Bell Tamper Rst Burg Z== Alarm Burg Z== Rstr Bypass Supr. Z== Codes Defaulted Comms Fail Printed (9853 only)* Bell Tamper Restore Burg: Z== Burg Restore Z== U== Sup.
3.
3.
3. Testing Commands 97: Engineer Walk Test This function enables the engineer to test all devices on the system. 1. Enter installer mode. 2. Press 97y 97: Walk Test The display shows: 3. Open and close each alarm and tamper contact in turn. The system gives a Chime tone each time you open and close a detector contact. The display shows: "A: Zone" and the zone number of every detector you have tested, in sequence and for one second each.
4. SYSTEM CONFIGURATIONS Using a Partitioned System Introduction When programming a control unit, there are two ways of changing from a single system to a partitioned system: a) during initial power up b) using Command 98. To create a partitioned system during initial power up, refer to the 9x5x Installation Guide. If you have an existing control unit that has already been programmed as a single system and wish to convert it to a partitioned system, then: 1. Enter installer mode. 2. Press 98y at the keypad.
4. System Configurations Programming Partitions Once you have selected a partitioned system, you can use the following commands to program each partition: 1. Use Commands 01 to 16 and X17 to X40 to assign each zone to a partition. Each zone defaults to Partition A. Press A to assign zones to Partition A. Press B to assign zones to Partition B. Press C to assign zones to Partition C. Press D to assign zones to Partition D. (See also "Setting Up A Common Area" on page 78.) 2.
4. System Configurations Differences in Commands for Partitioned Systems When you are using a partitioned system, some commands offer new options and others can no longer be used. The table below summarises the programming differences between partitioned and single systems.
4. System Configurations Common Areas Setting up a Common Area You can create a common area linked to two or more partitions. The system sets the common area when the users have set all the linked partitions. When users enter the common area using the appropriate access code, the system unsets it and any partition selected by the user. The remaining partitions stay set. The following sections show examples of how to use common areas. Example 1.
4. System Configurations To see how this works, start with what happens at the end of a working day when all the users leave the building. User A happens to leave first, and sets Partition A from the keypad in Office A. The control unit completes setting Partition A when the user closes zone 2. A few moments later, users B and C set their partitions. The control unit completes setting Partitions B and C when the users close zones 3 and 4 respectively.
4. System Configurations Office A Partition A Z4 Office B Partition B KPD KPD Z2 Z3 Lobby Common Area Z1 Figure 4. Using a Private Door Partition A has a separate exit guarded by a Final Exit zone (zone 4). Partition B is set. User A starts setting at their keypad and then leaves by their private door on zone 4. The control unit is expecting to see zone 1 close in order to complete setting Partition A and the common area.
4. System Configurations Example 2. Double Common Area You are not limited to having one common area. Figure 6 shows three partitions sharing two common areas. Common Area 2 KPD KPD Partition B Partition A KPD Partition C Common Area 1 Figure 6. Using two Common Areas The control unit sets Common Area 1 when users set Partitions A and B. The control unit sets Common Area 2 when users set Partitions B and C. Example 3.
4. System Configurations Partition D remains set during the day. Partitions A, B and C are unset, so the control unit leaves the common area unset. When users A, B and C leave at the end of the day the control unit sees that all partitions are set and sets the common area. When the cleaners arrive in the evening, they open zone 1 and the control unit starts the entry timer. The cleaners unset Partition D and the control unit unsets the common area but leaves Partitions A, B and C set.
4. System Configurations DD243: 2004 Compliance Applicability Please study this section if all of the following apply: 1. You are installing an alarm system in England, Wales or Northern Ireland. 2. The system has remote signalling and requires the local Police Authority to issue a URN (Unique Reference Number). 3. You have chosen to use "Sequential Alarm Confirmation" to comply with DD243: 2004.
4. System Configurations The table below summarises which options to select on various commands in order to comply with paragraphs 6.4.2 to 6.4.6. DD243: 2004 Para: Possible Installation Command 89 160 48 163 164 Alarm Confirmation Confirmation Time Lockout Keypads During Entry Confirmation on Entry User Reset After Confirmation 6.4.2 Unset from outside the premises using a keyswitch zone input – entry must be prevented until system is unset No (Option 0) Never (Option 0) Enabled (Option 1) 6.4.
4. System Configurations PD 6662 / prEN 50131-1: 2004 Compliance EN 50131-1: 2004, Alarm systems – Intrusions and Hold-up Systems – Part 1: System Requirements, requires that an alarm system does not display any detailed information until a user enters a valid access code or presents a valid proximity tag. The system should display an alert to inform users that there is information to view.
4. System Configurations Programming for Compliance Use the following setting to ensure compliance with PD 6662 / prEN 50131-1: 2004.
Index 24-hour Alarm ............................................................. 37 Abort Alarm ..................................................................... 18 reset after an Abort Alarm ..................................... 25 AC Fail Override ......................................................... 55 AC Fail Reset.............................................................. 54 Access code.............................................................. 3, 7 length................................
Index Exit mode Level/Partition A.....................................................20 Level/Partition B.....................................................29 Level/Partition C.....................................................32 Level/Partition D.....................................................34 Exit Terminate button using in common areas..........................................79 Exit time Level/Partition A.....................................................23 Level/Partition B................
Index PD6662 compliance ... 14, 15, 16, 17, 19, 22, 23, 26, 27, 28, 30, 33, 35, 42, 43, 44, 53, 54, 55, 56, 60, 64, 66 Print printing event log during normal operation ............ 63 printing event log during testing............................. 70 Programming entering installer mode ............................................ 2 leaving installer mode.............................................. 3 leaving programming mode ................................... 41 using programming commands .................
Index Cooper Security Ltd. Security House Vantage Point Business Village Mitcheldean Gloucestershire GL17 0SZ www.scantronic.co.uk Product Support (UK) Tel: +44 (0)870 7575400 Available between: 08:15 and 17:00 Monday to Friday Product Support Fax: +44 (0)1594 545401 Part Number 497096 Issue 3 Declarations of conformance to standards can be obtained from our Web site, www.scantronic.co.
