INSTALLATION AND PROGRAMMING GUIDE HARDWIRED CONTROL UNIT
9651 Hardwired Control Unit Installation Guide This document applies to control panels using software version 4.03.10 or later. © Cooper Security Ltd. June 2007 Every effort has been made to ensure that the contents of this book are correct. However, neither the authors nor Cooper Security Limited accept any liability for loss or damage caused or alleged to be caused directly or indirectly by this book. The contents of this book are subject to change without notice. Printed and published in the UK.
Contents 1. INTRODUCTION.......................................................................................... 1 About this Manual ........................................................................................................................................1 Features of the Control Unit .........................................................................................................................2 Elements of the IAS ...................................................................
Contents 9651 List of Figures Figure 1. Elements of an Intruder Alarm System..........................................................................................3 Figure 2. 9930 and 9940 Keypads ...............................................................................................................4 Figure 3. Control Unit PCB Layout.............................................................................................................10 Figure 4. Backplate of the 9940 Keypad .............
1. INTRODUCTION About this Manual This manual is divided into four chapters: 1. Introduction: this describes the parts of an Intruder Alarm System (IAS) based on the 9651 control unit. 2. Technical Description: this defines the operating parameters of the different parts of the system. 3. Installation: this explains the tasks involved in installing an IAS using the 9651 control unit. 4. Programming: this explains how to enter and exit programming, and lists the commands available to the installer.
1. Introduction 9651 Features of the Control Unit The control unit provides: ° On-board connections for 8 Fully Supervised Loop (FSL) zones or 8 Closed Circuit Loop (CCL) zones with a common tamper. ° Connections for 3 fully programmable panel outputs. ° A 4-wire bus for keypads. ° Internal sounder loudspeaker output with Chime, Alarm, Fire and Entry/Exit tones (the volume of the Entry/Exit and Chime tones can be adjusted).
9651 1. Introduction Elements of the IAS An IAS comprises a control unit in a shielded case, with 1 to 4 separate keypads and various detectors or other devices, for example keyswitches, connected to programmable zones. The control unit has eight zone connectors on its printed circuit board (PCB). Figure 1 shows how these elements are connected. In this example, the control unit (1) is directly connected to 6 detectors (3) and 2 door contacts (4). There are 4 keypads (2) on the bus.
1. Introduction 9651 9930 and 9940 Keypads 9940 Keypad 9930 Keypad A B C 1 2 4 5 6 7 8 9 D 3 0 Figure 2. 9930 and 9940 Keypads The control unit supports the connection of 9930 and 9940 keypads. The 9940 is the later replacement for the 9930, and offers smaller size, a built-in wide-area proximity reader and connections for an external panic alarm switch.
651 1. Introduction User Control The control unit provides 50 independent User access codes and a separate Duress Code. Users can change these codes at any time but cannot use them to program the system. During installation, the Installer can select whether access codes use four or six digits. Users can set only one level at a time. Level A sets the whole system. Levels B, C and D set parts of the system. The Installer allocates zones to levels, but all keypads operate the entire system.
1. Introduction 9651 (This page is intentionally blank.
2. TECHNICAL DESCRIPTION Control Unit Specification General Environmental Security Operating temperature Humidity Dimensions Weight Internal Clock Class 2 EN50131-1 or PD6662 Grade 2x -10° to +55°C 96% RH 235mm W, 245mm H, 90mm D 3.3 kg ±10 minutes over one year (depending on the accuracy of the mains supply frequency). Suitable for use in a system that is designed to comply with EN50131-1, ACPO-IAS Policy, NSI NACP14. Power Supply All currents accurate to ±5%.
2. Technical Description 9651 Outputs OP 1, 2, 3 LS AUX Communications outputs Open-collector transistor outputs, 500mA, 12VDC, negative applied. Supports two parallel-connected, externally mounted loudspeakers for internal sounder or EE tones: minimum speaker impedance 8Ω. 500mA, 12VDC minimum, 13.8VDC maximum, ripple ±2% maximum. 12V logic outputs, negative applied in alarm (positive removed), 50mA maximum.
9651 2.
2. Technical Description 9651 Control Unit PCB Layout Figure 3 shows the layout of the PCB used in the control unit. 1. Power input: 12vdc battery and 21vac from transformer (pre-wired) 2. Kick Start pins 3. Zone connectors 4. AUX power 5. Outputs (3 open collector outputs) 6. Tamper return from external sounder 7. Speaker connector 8. Keypad connector 9. NVM Reset pins 10. Plug-by (standalone) communicator connector 11. Processor in socket 12. Lid tamper switch Figure 3.
3. INSTALLATION Caution: Always remove mains power before opening the case lid. Do not work inside the control unit with mains power present. Overview A typical installation comprises the following main steps: 1. Survey the site and decide on positions for wired detectors, control unit, keypads, external and internal sounders. As part of the survey ask the users what facilities they need. 2. Ensure that there is a suitable mains supply present at the site of the control unit. 3.
3. Installation 9651 Cabling for Keypads Cooper Security recommends that you use 8-core 7/0.2 or 16/0.2 alarm cable for wiring keypads. You can connect the keypads in either a star or bus configuration. If you intend to use long cable runs, Cooper Security recommends that you use star wiring with no more than 200m of cable per branch. The maximum length of any one run from the control unit to the most remote keypad depends on the number of items connected to the cable.
9651 3. Installation Fitting the System Fitting the Control Unit Case 1. 2. 3. 4. Remove the control unit case from its packaging. Remove the front screws and slide off the case lid. The upper part of the case back has a central keyway. Mark and drill a hole for the keyway. Temporarily fix the case back to the wall. Mark the position of two more fixing holes, remove the case back and drill the holes. Refit the case back to the wall using screws no less than 30mm x No 8, with dome or pan heads.
3. Installation 9651 Fitting a 9930 Keypad The backplate of the 9930 keypad (see Figure 5) contains an adjustable cam that you can use to make sure the tamper switch will operate correctly when the keypad is mounted on an uneven surface. Cooper Security recommends that you mount the keypad using No 8 or 6 screws (M4/M3.5) as follows: 1. Remove the front cover by first releasing the screw located on the bottom edge of the keypad. 2.
9651 3. Installation Fitting the ScanProx 934 Module Note: If fitting a 934 module to an existing installation, put the alarm system into programming mode and then remove all power, both mains and battery. If you do not remove all power, the system will not recognise the 934 module. 1. 2. Remove the front cover from the keypad(s) to which you intend to fit the module. Remove the cable clips (item 4 in Figure 5). Fit the 934 module to the connector pins, as shown in Figures 6 and 7. Figure 6.
3. Installation 9651 Wiring the Control Unit Cable Entries The control unit case back provides several cable entries. It is designed to stand away from the wall to leave space for the cables. Mains Connection Connect the control unit to a suitable supply using a double pole disconnect device in accordance with EN60950-1:2001 Clause 3.4.3. Connect the supply to the control unit using the 3-way terminal block located on the case back. Secure the cable to the case anchor point using the cable tie provided.
9651 3. Installation Keypads Connecting Keypads Figure 10 shows the connections for keypads. Use the "ET" connector terminals on the keypad PCB to connect an exit terminate button or lock switch. If you are using a lock switch, do not connect any other devices to these terminals. 9930 Keypad 0V12V CLK DATA ET Lock Switch Or Exit terminate button (NO, push to make) Control Unit 0V12V CLK DATA 4-core To other keypads Figure 10.
3. Installation 9651 Keypad Addressing The control unit is supplied with one keypad. If you have fitted more keypads, each one must be given a separate "address". Links LK2 to LK4 set the keypad address, as shown in Figure 12. Keypad 1 Address Keypad 2 2 2 2 3 3 3 4 4 4 Keypad 3 Keypad 4 2 2 3 3 4 4 ON BACKLIGHT ON BACKLIGHT Backlight ON ON BACKLIGHT Backlight OFF Figure 12.
9651 3.
3. Installation 9651 Connecting Detector Circuits to the Main PCB The connectors for the detector circuits, or zones, are on the left-hand edge of the main PCB in the control unit. The table below summarises the number and type of zones that can connect to the main PCB of the control unit. Use Command 21 to specify which of these wiring types you are using. You cannot specify different wiring types for different zones.
9651 3. Installation The wiring resistance of the cable to the detector (including joints) should not exceed 100 ohms. The recommended maximum cable length within a zone is 200–300m. Figure 15. FSL Connections 4k7 Yellow Violet Red Gold 2k2 Red Red Red Gold Figure 16.
3. Installation 9651 Programming Outputs Control unit panel outputs can be programmed using the commands shown in the table below. Open collector outputs are of a "pull down" type that provides negative-applied control signals; the system adjusts the output polarity when you select the output type. Output OP1 OP2 OP3 Type open collector open collector open collector Command 81 82 83 Figure 17 shows some examples of applications for open collector outputs (OP3 is used in these examples).
9651 3. Installation Wiring Keyswitches To allow a user to set and unset the system using a keyswitch, connect a fixed position or spring loaded (momentary) key switch to a zone input. When programming the control unit select zone type (KM) for momentary or (KF) for fixed position keyswitches. See Command 185 for keyswitch auto-reset. Figure 18 shows the connections for a keyswitch.
3. Installation 9651 The 9928 can be connected to either a momentary or a latched keyswitch (see Figure 19). When using a momentary keyswitch, remove the jumper from link M/C. When using a latched keyswitch, fit a jumper to link M/C. Note: If you connect a keyswitch through a keyswitch interface, it can be used to set and unset the whole system or Level B only.
9651 3. Installation Communicator The 9651 can be fitted with a communicator or speech dialler, for example the Scantronic 660, 8400, and 8440 digital communicators or the SD1, SD2 or SD3 Speech diallers. To connect an SD1, SD2 or SD3 follow the instructions provided with those products. Figure 20 shows the connections for the communications wiring harness. Figure 20. Plug-By Communicator Wiring Note: Comms O/P4 will be active when the system is unset.
3. Installation 9651 Figure 21. Fitting a Plug-by Communicator 3. 4. 5. Make any necessary connections from the communicator to the communication wiring harness. The default is a positive voltage when the output is inactive but this can be inverted if required using Command 159. Plug the Communication Wiring Harness onto the communications connector on the main PCB. Re-fit the PCB to the support pillars. Secure the PCB to the support pillars with the screws provided (Figure 22).
9651 3. Installation If the system has already been installed: 6. Re-connect the battery. 7. Fit the case lid. 8. Apply mains power. 9. Test communicator operation. Fitting a Battery Fit a rechargeable battery into the back of the case. There is space in the case for a 12V 7Ah battery; make sure the battery terminals are oriented in the position shown in Figure 23. 7AH Figure 23.
3. Installation 9651 Initial Start Up Before applying power to the control unit, ensure that: • All keypads have been addressed and connected. • All external and internal sounders are connected. • All wired zone circuits are connected. Then: 1. Connect the battery to the control unit PCB. 2. Briefly short the Kick Start pins together (see Figure 3). The internal sounder may sound. Ignore any display at this stage. 3. Key in the factory default User access code: 1234. The internal sounder stops.
4. PROGRAMMING Introduction This chapter is divided into four sections: 1. Introduction provides an overview of how to program a 9651 control unit. 2. Programming Commands lists and describes the commands available to program aspects of a 9651 control unit's operation. 3. Testing Commands lists and describes the commands available to test a newly installed alarm system based on a 9651 control unit. 4.
Programming 9651 In addition to the three standard operating modes, there is a special Duress mode which provides the same access as user mode but also secretly communicates the duress status. There is only one user code of this type. See Command 49 for details on how to enable Duress Code, and Commands 151-158 for details on how control the plug-by communicator outputs. Entering Installer Mode Chapter 3 describes how to enter installer mode for the first time in a new installation.
9651 Programming Leaving Installer Mode When you have finished programming the control unit: 1. Press 99y at the keypad The display shows: 2. Press y. The display shows: followed by the time and date. 99:Exit Eng ? 99:Checking Sys The system is now in user mode. Note: If any 24-hour, Fire, PA or Technical zones are active when you enter Command 99, the keypad gives an error tone and displays the faults. Correct the problems identified. When the display shows "No Faults", press y to enter user mode.
Programming 9651 Performing an Engineer Reset To perform an engineer reset: 1. Check that the display is showing the alarm condition. 2. Enter installer mode. 3. Enter 99 yy. The display returns to the time and date. Restoring Default Command Settings To restore all command options to their default (original) settings: 1. Enter installer mode. 2. Press 98y at the keypad. The display shows: Load Default 3. Press 1y at the keypad.
9651 Programming Figure 24. Sensitive Area on 9930 Keypad for Tag To Add a Tag 1. 2. Key in User 01 access code while the system is unset. The display shows: Press 4 to select the change codes option. The display shows: Select? Old Code= 3. EITHER Enter the access code of the user for whom you want to program a tag and press y. OR Press X repeatedly until the display shows the user number of the user for whom you wish to program a tag and press y.
Programming 6. 9651 Repeat steps 1 to 5 for other tags, as necessary. To Delete a Tag Note: If you delete a tag, you also delete that user's access code. 1. 2. 3. Key in User 01 access code while the system is unset. The display shows: Press 4 to select the change codes option. The display shows: Select? Old Code= Enter the User 01 access code again and press y. The display shows "User 01" and any text description for that user. 4.
Programming - Programming Commands 9651 Programming Commands 0: Country PTT Defaults Use this command to select the country and PTT (Public Telegraph and Telephone) defaults; it also loads default access codes and programming options. Use Command 126 to select language without making other changes. Note: If you select options X4, X5, X6 or X7 (Finland, Norway, Sweden or Denmark), the control unit changes the method of entering installer mode (see "Entering Installer Mode" on page 29).
Programming - Programming Commands 9651 The following table shows the letters generated by each key on the keypad. 1 2 3 4 5 6 ABCÆÅÄ DEF GHI JKL MNOØÖ 7 8 9 0 C D PQRS TUV WXYZ Space ' ( ) : . - ! & Move right Move left Zone Types The following table shows the values available for zone type. Value 00 01 02 03 04 05 06 07 Page 36 Type Not Used (NU) Description Identifies zones that are not used. The system ignores zones of this type.
9651 Programming - Programming Commands Value 08 Type Technical Alarm (TC) 09 Keybox (KB) 10 Smoke Detector (SD) 11/12 Keyswitch 13 Anti-Mask Zone (AM) Description Use this zone type when you want to monitor equipment, for example a freezer, without raising a full alarm. If a Technical Alarm zone is activated while the system is set, the system makes no audible alarm. However, when a user unsets the system, the keypad indicates a fault.
Programming - Programming Commands Value 14 Type Forbikobler (FB) 15 AC Fail (AC) 16 Low Battery (LB) Battery Fault (BF) Power Output Failure (PF) Fault (FL) 17 18 19 9651 Description This zone type is a Scandinavian type of Entry/Exit zone (the word "forbikobler" means "bypass" in Danish). Use this type for zones connected to standalone external keypads or access controllers.
9651 Programming - Programming Commands Value Attribute Valid for Description X2 Soak Test (S) Normal Alarm (NA) Entry Route (ER) 24-hour (24) Shock Analyser (SA) X3 Double Knock (D) Normal Alarm (NA) Entry Route (ER) X4 Omit Allowed (O) All Use this zone attribute if you want to place on long-term test a detector that you suspect is giving false alarms. Zones with this attribute are disabled for 14 days after you return the control unit to user mode.
Programming - Programming Commands 9651 Value Attribute Valid for Description A Armed in Level A Armed in Level B Armed in Level C Armed in Level D All Always applied. The zone is armed when the user selects Level A. When applied, the zone is armed when the user selects Level B. When applied, the zone is armed when the user selects Level C. When applied, the zone is armed when the user selects Level D.
9651 Programming - Programming Commands 23: Remote Reset Enable Option 1 enables Remote Reset, which is designed to operate with the plugby communicator. After an alarm, the user keys in an access code to silence the alarm but cannot reset the system. The first alarm message to display and the Service lamp remain visible. The user contacts the Alarm Receiving Centre (ARC), which verifies the user's identity and then sends a signal to the control unit.
Programming - Programming Commands Panel Set No alerts Alerts Panel Unset No alerts Alerts Text 0 1 continuous timed Level set Level set 30s, then T&D Level set Level set 30s, then T&D 0 1 continuous timed T&D T&D T&D T&D T&D Time and date * 9651 Alert lamp 0 1 continuous timed Off Off Service/Mains lamps 0 1 continuous timed On On* 30s On On 30s On On* 30s 0 continuous Off On 1 timed Off On 0 continuous On On 1 timed On* 30s On* 30s If a relevant condition exists Note: Compliance with PD 6
9651 Programming - Programming Commands 31: Zone Tamper User/Engineer Reset Use this command to ensure that the system complies with national requirements for resetting zone tamper indications while the system is unset. If you select option 0 (the default), the user can reset the system after a zone tamper.
Programming - Programming Commands 9651 Note: The Alarm Abort period is controlled by the Alarm Receiving Centre (ARC). 37: Daytime Tamper Communication This command defines how the control unit reports tamper indications (for example, an attempt to open a control unit or keypad case) while the alarm system is unset. Option 0 Internal sounder only (default). 1 Internal sounder and communication of tamper indication to the Alarm Receiving Centre (ARC).
9651 Programming - Programming Commands Notes on Lock Set: 1. Do not connect more than one lock switch (or any other device) to the keypad ET terminals. Do not attempt to fit two lock switches. 2. To set the system, the user first enters their access code at a keypad or operates a keyswitch. The control unit starts to emit the exit tone. The exit time is infinite in this option. The user then operates the Final Exit zone and turns the key in the lock switch to "locked".
Programming - Programming Commands 9651 41: Bell Delay When an alarm occurs (for example, an intruder violates a zone), the system waits for the Bell Delay before operating the external sounder for the Bell Duration. This command sets the Bell Delay. Note: Compliance with PD 6662 / prEN 50131-1: 2004 (see page 73) requires that the Bell Delay does not exceed 10 minutes and that it is not used for entry alarms. Option 0 No delay (default) 1 1.
9651 Programming - Programming Commands 3 30 seconds 4 45 seconds 5 60 seconds 6 120 seconds 45: Entry/Exit Tone Volume This command sets the volume of the Entry/Exit tone from the internal sounder. If you select option 0, the internal sounder emits no tone. Select a value from 1 (quietest) to 9 (loudest) to set the volume (default 5). The internal sounder demonstrates the volume when you enter the digit.
Programming - Programming Commands 1 9651 On. Duress Code. Note: If the duress code is disabled and then enabled again, the code previously assigned to it by the user will be lost. A new duress code must be assigned. 50: CSID Code To enable the user to use the "Remote Reset" facility (enabled with Command 23), you must program the control unit as "Engineer Reset" (Command 33 option 1) and install a four-digit Central Station Identification (CSID) code: 1.
9651 Programming - Programming Commands 53: Abort User/Engineer Reset This command specifies how the system is reset after an aborted alarm. Option 0 Use the reset option selected for the system with Command 33 (default). 1 Permit the user to reset after an abort. 56: Number of Digits in Access Codes The control unit can use either four-digit or six-digit access codes. Select option 0 for four-digit access codes and option 1 for six-digit access codes.
Programming - Programming Commands 9651 60: Level B Final Exit Operation In a single system, this command specifies how the system treats Final Exit zones during part set B. If you select option 0 (the default), Final Exit zones included in Level B continue to act as Final Exit zones during part set B. If you select option 1, these zones act as Normal Alarm zones during part set B.
9651 Programming - Programming Commands 65: Level B Exit Time This command sets the Exit Time for Level B. Option 1 10 seconds 2 20 seconds (default) 3 30 seconds 4 45 seconds 5 60 seconds 6 120 seconds 67: Forbikobler Approved This command specifies whether the Forbikobler system should operate in an approved manner (user codes only) or a non-approved manner (proximity tags and user codes).
Programming - Programming Commands 9651 70: Level C Final Exit Operation This command specifies how the system treats Final Exit zones during part set C. If you select option 0 (the default), any Final Exit zones in Level C continue to act as Final Exit zones during part set C. If you select option 1, these zones act as Normal Alarm zones during part set C. 71: Level C Entry Route Operation This command specifies how the system treats Entry Route zones during part set C.
9651 Programming - Programming Commands 75: Level C Exit Time This command sets the Exit Time for Level C. Option 1 10 seconds 2 20 seconds (default) 3 30 seconds 4 45 seconds 5 60 seconds 6 120 seconds 76: Level D Exit Mode This command sets the Exit Mode for Level D. The keypads give a double "beep" confirmation tone at the end of all setting modes, including Silent Set. The default is option 0, Timed. Option 0 Timed.
Programming - Programming Commands 3 30 seconds 4 45 seconds 5 60 seconds 6 120 seconds 9651 Note: You cannot change the operation of Final Exit and Entry Route zones assigned to Level D as you can with Levels B and C (see Commands 60, 61, 70 and 71). For this reason, Cooper Security recommends that you use Level D for simple applications only.
9651 Programming - Programming Commands 03 Set Latch: active when the system is set and inactive when the system is unset or an alarm condition occurs. It is active for one second when a reset is performed or the control unit leaves installer mode. It is also active during Walk Tests. 04 Shock Reset: used to reset shock sensors (for example, the "Viper"). The output is triggered by the control unit at the start of the Exit Time and remains active for five seconds.
Programming - Programming Commands 29 Pulse Set 4: active for time set by Command 170. 30 Pulse Unset 1: active for time set by Command 172. 31 Pulse Unset 2: active for time set by Command 172. 32 Pulse Unset 3: active for time set by Command 172. 33 Pulse Unset 4: active for time set by Command 172. 34 Fire: active during a Fire alarm. 9651 35 PA: active during a PA. 36 Set Fail: active for 60 seconds from when a set command fails.
9651 Programming - Programming Commands 87: Keypad Dual Key Alarms This command enables users to raise an alarm by pressing two keys on the keypad at the same time. Three types of alarms are available, each of which can be enabled or disabled independently. The default is disabled (option 0). Alarm type PA Medical Fire Key combination 1 and 3 4 and 6 7 and 9 Disable 0 0 0 Enable 1 1 1 Press A and B to scroll up and down through the types (PA, FI and MD).
Programming - Programming Commands 9651 If the system is unset, the control unit logs the event and the keypads emit a short audible tone every minute. Entering a valid access code silences the sounders and the keypad displays indicate a telephone line fault. The system can be set again with the line fault present. If the system is set, the control unit logs the event but the keypads do not emit a tone or display a message.
9651 2 Programming - Programming Commands Installer Reset. An alert is generated when the mains power supply fails and can be cleared only by the installer when the supply is restored. Note: Compliance with PD 6662 / prEN 50131-1: 2004 (see page 73) requires that Command 134 is set to 1 or 2 (Cooper Security recommends 1). 135: Line Fault User/Installer Reset Use this command to determine how Line Fault alerts are reset. Option 0 No Reset Required (default).
Programming - Programming Commands 9651 Note: Insurance policies that are conditional on compliance with PD 6662 / prEN 50131-1: 2004 (see page 73) may require that Command 137 is set to 1 or 2 to restrict the user's ability to override alerts. 138: Line Fault Override Use this command to determine how Line Fault alerts can be overridden. Option 0 Never. The user cannot override Line Fault alerts when setting the system and must first reset them. Command 135 determines how the alerts can be reset.
9651 Programming - Programming Commands 140: Fault Override Use this command to determine how alerts can be overridden for all faults that do not have an individual override command. Option 0 Never (default). The user cannot override a Fault alert when setting the system. 1 Inactive. The user can override a Fault alert when setting the system, provided that the cause of the fault has been rectified.
Programming - Programming Commands 9651 Option 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 Not Used Fire PA Burglar Open/Close Alarm Abort Technical Alarm Not used RF Low Battery Supervision Loss RF Jamming AC Fail Tamper Alarm (day tamper) Open Close Zone Omitted Medical Assistance Key Box Anti-Mask 19 20 21 22 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 Smoke Detector Not used Battery Fault System Alarm Not used Not used Not used Pulse Set OP 1 Pulse Set OP 2 Pulse Set OP 3 Pulse Set OP
9651 Programming - Programming Commands 159: Invert Plug-by Outputs By default, plug-by outputs have a positive voltage when inactive and this is removed when the output is active. This command inverts that logic so that a positive voltage is applied when the output is active. Option 0 +ve removed to trigger (default): the output is positive when inactive and goes to zero when active. 1 +ve applied to trigger: the output floats when inactive and goes positive when active.
Programming - Programming Commands 9651 Example 1 Panel output 3 is to be programmed as type 12 (Pulse Set 1). It will be used to operate a locking mechanism when the whole system is set. The locking mechanism requires a 6-second pulse. The table below shows how to program the system to generate the required pulse. Command 83 170 171 Value 12 Set 1 = 06 Set 1 = a Description Sets panel output 3 to type Pulse Set 1. Sets the duration of Pulse Set 1 to 6 seconds. Allocates Pulse Set 1 to Level A .
9651 Programming - Programming Commands Note: Compliance with PD 6662 / prEN 50131-1: 2004 (see page 73) requires that Command 185 is set to option 0. 199: Display Zone Circuit Resistance For information on this command, see page 72. 200: Forbikobler Entry Timer This command sets the interval between a user entering the premises through a Forbikobler entrance and an alarm going off, using one of the independent entry timers configured with Commands 201 to 204.
Programming - Programming Commands 9651 Option 1 10 seconds 2 20 seconds (default) 3 30 seconds 4 45 seconds 5 60 seconds 6 120 seconds Note: By default, Entry Timer 1 is assigned to all relevant zones.
9651 Programming - Programming Commands Setting Entry Timers for both FE and ER Zones Suppose that you have installed a system that uses the Final Door exit mode. In this case, the entry timer will usually be started when a user opens the final door. It might seem unnecessary to assign an entry timer to an ER zone set up inside but there are two types of situations which make it useful to do so. 1.
Programming - Testing Commands 9651 Testing Commands 90: Reading the Event Log The control unit keeps a log of recent events. The log can contain up to 700 events. Each event is described by a short text message. To review the event log, make sure the system is in installer mode and then: 1. Key in 90y. The display shows the most recent event in the log. 2. Key in 1 to show earlier events or 3 to show later events. 3. Key in 4 to show the first event or 6 to show the last event. 4.
9651 Keypad Display Batt Flt Rstr Batt Load Fail Batt Missing Bell Tamper Bell Tamper Rst Burg Z== Alarm Burg Z== Rstr Codes Defaulted Comms Fail Config Changed Defaults Loaded EEPROM Fail F== Missing F== Restore F== Tamper Fire Reset Fire Z== Alarm Fire Z== Rstr Forbi I/F Tamper Forbi Lp Tamper Fr K== Alarm Frb I/F Tamp Rst Frb Lp Tamp Rst Global T.
Programming - Testing Commands Keypad Display PA Z== Alarm PA Z== Rstr Set Fail Z== Smk Det Alm Z== Smk Det Res Z== Soak Fail Z== System Rearmed System Startup System Tamp Rst System Tamper Tamper F== Rstr Tamper K== Rstr Tamper Z== Tamper Z== Tamper Z== Rstr Tech Z== Alarm Tech Z== Rstr U== # Set U== # UnSet U== Change U== U== Delete U== U== Duress U== Off-Site U== On-Site U== System Reset U== Time/Date U== Z== Omit U== Z== Unomit UserCode req off UserCode req on XT ACFl Rst Z== XT ACFl Z== XT BatFl Rst Z=
9651 Programming - Testing Commands Keypad Display Z== Lock Out Z== Lock Out Rst Meaning The system locked out the zone when attempting to rearm at the end of the bell run time. The system restored a locked out zone zone. Note: The log is protected and cannot be erased by the Installer or a user. 91 to 96: Testing Outputs You may test parts of the system by entering commands at the keypad.
Programming - Testing Commands 9651 199: Display Zone Circuit Resistance This command lets you view the resistance of zones connected to the control unit. Either key in the zone number (single digit 1 to 8 only) or press C to step up and A to step down through the zones. The bottom line of the display shows the word “Panel” followed by the zone type, and then the resistance of the zone in kilo Ohms. If the display shows “O/C” then the zone is open circuit. “0k0” means that the zone is short-circuit.
9651 Programming - System Configurations System Configuration PD 6662 / prEN 50131-1: 2004 Compliance EN 50131-1: 2004, Alarm systems – Intrusions and Hold-up Systems – Part 1: System Requirements, requires that an alarm system does not display any detailed information until a user enters a valid access code or presents a valid proximity tag. The system should display an alert to inform users that there is information to view.
9651 Programming Commands Quick Reference Command 0 Country PTT Defaults (page 35) n= Country: 0 = UK 1 = Italy (I) 2 = Spain (EE) 3 = Portugal (P) 4 = Netherlands (NL) 5 = France (FR) 6 = Belgium (B) 7 = Germany (D) 8 = Switzerland (CH) 9 = Austria (A) X1 = Ireland (IRL) Key in: 0yny Command b= X2 = S (14-day Soak Test) Y X3 = D (Double Knock) X4 = O (Omit Allowed) X7 = 1–6 or 1–4 For zone type 07, shock analyser sensitivity: 1 (low) to 6 (high) For zone types 05, 06 and 14, entry timer number: 1
9651 Programming Commands Quick Reference Command 30 n= 31 n= 33 n= 34 n= 35 n= 36 n= 37 n= 38 n= 1 Delay On PA Response (page 42) 0 PA response audible 1 PA response silent Zone Tamper User/Engineer Reset (page 43) 0 User reset after zone tamper 1 Engineer reset after zone tamper System User/Engineer Reset (page 43) 0 User can reset the system 1 Engineer must reset the system PA User/Engineer Reset (page 43) 0 User reset after PA 1 Engineer reset after PA First Circuit Lockout (page 43) 0 Lockout first
Programming Commands Quick Reference 9651 Command Key in: Command Key in: 62 Level B Exit Mode (page 50) 76 Level D Exit Mode (page 53) n= 0 Timed low tone on setting 1 Instant (no exit tone) 2 Silent (double "beep" after exit time) 3 Sets exit mode the same as Level A Level B Alarm Response (page 50) 62yny Y n= 76yny Y 63yny 77 0 Timed low tone on setting 1 Instant (no exit tone) 2 Silent (double "beep" after exit time) 3 Sets exit mode the same as Level A Level D Alarm Response (page 53)
9651 Programming Commands Quick Reference Command 82 Output 2 Type (page 54) nn = See Command 81 for a list of options. Default is 08 Strobe 83 Output 3 Type (page 54) nn = See Command 81 for a list of options. Default is 03 Set Latch 85 Burg Communication Rearm (page 56) 0 Latched 1 Rearm n= 87 Keypad Dual Key Alarms (page 57) n= 0 Off 1 On (PA enabled) 0 Off 1 On (Fire enabled) 0 Off 1 On (Medical enabled) Note: Setting PA to option 1 also enables a PA from keyswitches.
Programming Commands Quick Reference Command 151 nn = 152 n= 153 n= 154 n= 155 n= 156 n= 157 n= 158 n= Key in: Plug-by Communications Output 1 (page 61) 00 Not Used 01 Fire 02 PA 03 Burglar 04 Open/Closed 05 Alarm Abort 06 Technical Alarm 07 Not used 11 AC Fail 12 Tamper Alarm 13 Open 14 Close 15 Zone Omitted 16 Medical 17 Keybox 18 Anti-Mask 19 Smoke Detector 20 Not used.
9651 Programming Commands Quick Reference Command 201 Entry Timer 1 (page 65) n= 1 10 seconds 2 20 seconds 3 30 seconds 4 45 seconds 5 60 seconds 6 120 seconds Entry Timer 2 (page 65) 202 n= 1 2 3 4 5 6 10 seconds 20 seconds 30 seconds 45 seconds 60 seconds 120 seconds Key in: 201yny Command 203 Entry Timer 3 (page 65) n= 1 10 seconds 2 20 seconds 3 30 seconds 4 45 seconds 5 60 seconds 6 120 seconds Entry Timer 4 (page 65) Y 202yny 204 n= Y 11772232 1 2 3 4 5 6 10 seconds 20 seconds 30 s
9651 (This page is intentionally blank.
9651 Index 24-hour Alarm ...............................................................55 Abort Alarm .......................................................................43 reset after an Abort Alarm.......................................49 AC Fail Override ...........................................................59 AC Fail Reset................................................................58 Access code................................................. 5, 28, 31, 35 length..........................
Index 9651 Fully Supervised Loop (FSL) ....................................... 40 connections............................................................. 20 Fuses........................................................................ 8, 16 General Fault output .................................................... 56 Guard Code.................................................................. 40 Hide status display ....................................................... 41 Humidity........................
9651 Index PA alarm..................................................................43 performing engineer reset.......................................32 remote .....................................................................41 shock .......................................................................55 system reset ............................................................43 Restore access codes ..........................................................31 defaults..............................
Cooper Security Ltd. Security House Vantage Point Business Village Mitcheldean Gloucestershire GL17 0SZ www.scantronic.co.uk Product Support (UK) Tel: +44 (0)870 7575400 Available between: 08:15 and 17:00 Monday to Friday. Product Support Fax: +44 (0)1594 545401 Part Number 11772232 Issue 2 Declarations of conformance to standards can be obtained from our Web site, www.coopersecurity.co.
