USER GUIDE 9651 HARDWIRED CONTROL PANELS
Contents 1. Introduction ........................................3 The Alarm System................................3 The Keypad..........................................3 About This Guide .................................5 2. Everyday Operation ...........................6 How Do I Know if the System is Working?..............................................6 Setting the System ...............................6 Timed Set.........................................7 Exceeding the Exit Time ..................
1. Introduction The Alarm System The 9651 alarm system comprises a control unit, one or more keypads, and various detectors. The control unit is a box that houses the main controller, power supply, stand-by battery, and any remote communicator. The control unit is normally fitted out of sight in a safe place (for example under the stairs). The detectors are installed at various places, or zones, around the premises. If something triggers a detector then the detector signals back to the control unit.
1. Introduction 1. Line Fault LED 2. Service LED 3. Power LED 4. Level setting keys. 5. Omit key. 6 Enter Key 7 Fire alarm keys. Press 7 and 9 together. 8. Medical assistance keys. Press 4 and 6 together. 9. Optional programmable panic alarm keys. Press 1 and 3 together. 10. 16 digit Liquid Crystal Display (LCD). 1 4 “Proximity” Tag Reader Area Figure 1. 9930 LCD Remote Keypad. The display shows the state of detector zones, the anti-tamper wiring, and other information as necessary.
1. Introduction 6 7 8 9 X Y Set the internal clock/calendar, which provides a time stamp on log entries. Enable or disable the Chime facility. Start a test of the sounders and strobe. Start a test of the detectors. (See "4. Special Functions".) Omit individual zones or start again if you make a mistake when entering access codes. Enter programming and setting/unsetting commands. About This Guide The rest of this guide tells you how to use the system in more detail: 2.
2. Everyday Operation There are several different ways of setting the system. For all methods (except using a keyswitch) you must enter your access code or present a tag at the keypad. The keyswitch method uses a key in a special switch fitted to your premises. "Setting the System" below describes each method. Ask your Installer to provide the method that suits your site best. During installation the Installer programs the system to create an exit route for your premises.
2. Everyday Operation Timed Set With Timed Set the system sets after a programmed exit time has expired. Ask your Installer to make sure the exit time is long enough for you to leave the premises and close the final door. 1. Close all doors and windows. 2. Key in your access code or present a tag at the keypad. 3. Press the appropriate Level key. Note: If you press Y at this point the system sets at Level A. The exit time starts when you press Y or the Level key.
2. Everyday Operation Final Door Set With Final Door Setting the system sets when you close the last door. There is no fixed exit time. 1. Close all doors and windows. 2. Key in your access code or present a tag at the keypad. 3. Press the appropriate Level key. The keypad starts the continuous exit tone. Setting A --Exit tone Leave via the designated exit route and close the final door. The system sets seven seconds after you close the door and gives Level A set a double "beep".
2. Everyday Operation Part Setting The Installer may have programmed your system so that you can protect part of the premises while the rest is in use. Level keys B, C and D give different part set areas. Level key A always sets the full system. Ask your Installer which zones keys B, C and D cover. To part set: 1. Close doors and windows in the protected area. 2. Key in your access code or present a tag at the keypad. 3. Press B, C or D.
2. Everyday Operation Keyswitch Setting 1. Close all doors and windows. The Ready lamp on the keyswitch should be glowing to indicate that all the detectors are closed. (Some types of keyswitch do not have lamps.) Armed Ready Full Off Part Armed Ready Full 2. 3. Either turn the keyswitch to "Full" to set Level A Or turn the keyswitch to "Part" to set Level B. Leave the premises and close the final door. The system gives a double "beep" at the end of the exit time and sets. The Armed lamp glows.
2. Everyday Operation Lock Set Your installer may have fitted a special lock so that locking the final exit door completes the setting sequence. (The lock contains a switch so that the control unit can sense whether the lock is open or closed). To use Lock Set: 1. Close all doors and windows. 2. Key in your access code or present a tag at the keypad. 3. Press the appropriate Level key. The keypad starts the Setting A --continuous exit tone.
2. Everyday Operation If the System Will Not Set Detector Active If you try to set the system while something is triggering one of the detectors in the protected area (for example a door or window is still open) then the keypads or internal sounder will give an interrupted tone and the display will show the zone number of the detector. 1. Go to the zone shown on the display and find out what is triggering the detector. If possible remedy the fault. 2. Return to the keypad and set the system again.
2. Everyday Operation What To Do When Service and Line Fault Glow If you hear an intermittent tone from the keypad, and both the s and f lamps glow then your system may have experienced a temporary telephone line fault. 1. Key in your access code or present a tag The tone stops and the display may briefly Plugby line fail show: The s and f lamps will continue to glow for as long as the fault is present. If the system detects that the fault has been rectified, then the s and f lamps go off.
2. Everyday Operation Unsetting the System WARNING: If you enter your premises and an internal alarm starts then there may be an intruder. Unsetting From a Keyswitch Turn the keyswitch to OFF. The system unsets immediately. Unsetting From the Keypad The system has a programmed entry time. Ask your Installer to make sure the entry time is long enough for you to enter by the designated entry route, get to the keypad and unset the system. The entry time starts when you open the designated entry door.
2. Everyday Operation Unsetting with a Lock Switch If the installer has fitted the final exit door with a lock switch: 1. Unlock the door. The keypad gives a continuous exit tone. At this point you can lock the door again and the system will remain set. Exit tone 2. Enter through the designated entry door and go to the keypad. As you enter the premises the system starts the entry timer and the keypads give the entry tone. Entry tone 2. Key in your access code or present a tag.
2. Everyday Operation Starting Alarms Yourself There are three types of alarm that you can start yourself: PA (Panic), Medical Assistance, and Fire. Your Installer must program your system to enable these functions. You can start these alarms from the keypads by pressing two keys at the same time. Remember: To start a Panic Alarm: On a keypad press 1 & 3 together. To start a Medical Assistance Alarm: On a keypad press 4 & 6 together. To start a Fire Alarm: On a keypad press 7 & 9 together.
3. After an Alarm When your system raises an alarm you must disarm it in order to switch off the sounders and strobes. The system keeps a record of which zone(s) triggered the alarms, and shows the zone number(s) on the keypad display. Once you have disarmed the system, you must reset the system before you can start using it again. Fire Alarm The system gives a fire alarm by sounding a warbling tone from the keypads and alarm sounder. The display shows the letters "Fire". 1.
3. After an Alarm • If the s lamp glows after an alarm and your system is connected to an communication device then your system may use Remote Reset. Your alarm company will give you instructions over the phone and a special code so that you can reset the system from the keypad. Customer Reset 1. Key in your access code or present a tag and press Y. The display clears. 2. You can now use your system as normal. Remote Reset Before starting this process, make sure you have a pen and paper to hand.
4. Special Functions Introduction From the keypad you can perform a number of other functions, apart from setting and unsetting the system. These functions are: [Access code] + X Omitting zones. [User 01 Access code] + 4 Changing access codes and user names. [Access code] + 5 Reading the system log. [User 01 Access code] + 6 Setting the time and date. [Access code] + 7 Turning the chime on or off. [Access code] + 8 Testing the sounders. [Access code] + 9 Testing the zones.
3. After an Alarm 5. 6. Key in your access code (or present a tag) and press a Level key.. The control unit gives an error tone and the A:Omit Zone 07? display shows (for example): 7. Press Y. If necessary, press Y again for each omitted zone shown on the display. (If you wish to escape press X.) After you press Y for the final omitted zone the control unit starts to set. To reinstate a zone repeat steps 1 to 4. At step 3 press Y and “o” will disappear. Press X to exit. Omissions are not permanent.
3. After an Alarm Changing Access Codes 1. Enter User 01 access code. The display shows: 2. Select? Press 4. The display shows: Old Code= Note: If the system does not already have a code then it uses X002 for user 02, X003 for user 03 and so on. 3. 4. Key in the access code you wish to change and press Y. The display shows (for example): U02:User At this point you can change the text that the system displays on the keypad for each user code. See "Changing User Names" below.
3. After an Alarm ABCÆÅÄ DEF GHI JKL MNOØÖ PQRS TUV WXYZ Space'():.-!& Figure 3. Letters Generated by Each Number Key Proximity Tags If the installer has fitted your keypad with a 934 SCANPROX module you can program the system to recognise individual proximity tags. Users can then employ these tags in place of access codes. A tag acts as an alternative to a user access code. You can assign a user a tag, an access code, or both.
3. After an Alarm 4. 5. 6. The display shows the user number and any text description you have programmed for that user. Press Y. The display shows the user number and an underscore, for example: Present the proximity tag to the front of the keypad (see page 4). The system learns the identity of the tag and links it to that user number. The keypad gives a double beep to show that the system has learned the tag successfully. The keypad displays the date and time.
3. After an Alarm Using the Log The system keeps a log of the last 250 events. You can examine this log from the keypad. To use the log: 1. Key in your access code or present a tag 2. Press 5. The display shows the most recent event, U01 Change U02 for example: The display shows a short message for each type of event. Table 1 on the next page shows each of the messages that you might see, and their meaning. 3. Press Y to toggle the display between the time and date of the event and the log report.
3. After an Alarm Set Fail Znn Burg Znn Rstr Tamper Znn Knn Missing Knn Restore Knn Tamper Knn Excess Keys Tel Line Fault Tel Line Rstr Comms Fail AC Fail AC Restore Low Battery Low Batt Rstr Batt Missing Batt Missing Rstr Aux DC Fail Aux DC Fail Rstr Setting failed because of zone nn. Intruder alarm at zone nn restored. Tamper at zone nn. Keypad nn missing. Keypad nn restored. Tamper at keypad nn. Too many keys pressed at keypad nn (someone may be trying to guess the access code).
3. After an Alarm Setting the Time and Date The control unit contains an internal clock/calendar that runs as long as there is power present (mains or stand-by battery). The system uses this clock to mark the time and date on the system log. If the power supply fails for any reason, and the stand-by battery is low, then the system loses track of the correct time and date. You may also need to change the time if you live in a country that uses summer/winter time.
3. After an Alarm Testing the System Bell Test You can test that all the sounders and the strobe are working, as follows: 1. Key in your access code. or present a tag 2. Press 8. The system turns the external sounder, internal sounder(s) and keypad sounders on for three seconds each, one after the other. The strobe flashes for six seconds to give you time to see it. Walk Test You can set the system so that it will allow you to walk round the premises and test each of the detectors (a walk test).
3.
