Specifications

4" Low Voltage
84
DIMENSIONS
DESCRIPTION
The ET400LV is a small aperture
low voltage housing for providing
accent and task lighting. For use in
non-insulated ceilings. If ceiling
insulation is present, it must be kept
3" from the fixtures on all sides.
Housing
Die-formed CRS with gray powder
coat finish.
Plaster Frame
• Housing is secured in plaster frame
with spring barbs.
• The housing can be adjusted in the
plaster frame.
• The housing can be removed from
the plaster frame to provide access
to the junction box.
Junction Box
• Positioned to accommodate straight
conduit runs.
• Seven conduit knockouts are
uniform 1/2" size with true pryout
slots.
• Four pryouts with integral strain
relief simplify “NM” non-metallic
sheathed cable installation.
• Three quick connect wire connectors
included.
ALL-NAIL™ Bar Hangers
Bar Hanger features include:
• Pre-installed nail.
• Mini leveling foot aligns the housing
to the bottom of the joist.
• Housing can be positioned at any
point within 24” joist spans
• Score lines allow tool-free
shortening for narrow joist spacing.
• Bar hangers may be repositioned
90° on plaster frame
• Integral T-bar clip snaps onto T-bars –
no additional clips are required
Socket
Ceramic socket with reflector for
bi-pin 12V, MR16 lamps.
Transformer
120V Integral magnetic transformer
steps line voltage down to lamp
operating voltage.
Thermal Protector
Thermal protector integrated in the
transformer deactivates fixture if
overheating occurs due to improper
operating condition or misapplied
insulation.
Labels
• UL/cUL Listed 1598 Luminaire
• UL/cUL Listed for Damp Location
• UL/cUL Listed for Feed Through
• UL/cUL Listed for Wet Location,
covered ceiling
• IP Rated (Improper Lamp)
• Certified Under ASTM-E283 for
air tight construction
Note: Some units may have
different features.
Visit www.cooperlighting.com for more information on the complete ALL-PRO Stock and
Specification offering. Product availability subject to change without notice.
DIMENSIONS
DESCRIPTION
The EI400LVAT housing has an
integral low voltage transformer
that supplies 12 volts to MR16 lamps.
It can be used in ceilings where it will
be in direct contact with insulation.
AIR-TITE design meets restricted
airflow requirements.
Housing
Double wall aluminum construction
for greater heat dissipation. EI400LVAT
housing is gasketed to prevent airflow
from heated or air conditioned spaces.
Plaster Frame
• Galvanized steel construction.
• The inner housing can be removed
from the plaster frame to provide
access to the junction box.
• Plaster frame includes locking
screws for hanger bars and cutouts
for crimping hanger bars in
position.
• AIR-TITE gasket is pre-installed.
Junction Box
• Positioned to accommodate
straight conduit runs.
• Seven conduit knockouts are
uniform 1/2” size with true pryout
slots.
• Four pryouts with integral strain
relief simplify “NM” non-metallic
sheathed cable installation.
• Three quick connect wire
connectors included.
ALL-NAIL™ Bar Hangers
Bar Hanger features include:
• Pre-installed nail.
• Mini leveling foot aligns the housing
to the bottom of the joist.
• Housing can be positioned at any
point within 24” joist spans
• Score lines allow tool-free
shortening for narrow joist spacing.
• Bar hangers may be repositioned
90° on plaster frame
• Integral T-bar clip snaps onto T-bars –
no additional clips are required
Socket
Ceramic socket with reflector for
bi-pin 12V, MR16 lamps.
Transformer
120V Integral magnetic transformer
steps line voltage down to lamp oper-
ating voltage.
Thermal Protector
Thermal protector integrated in the
transformer deactivates fixture if
overheating occurs due to improper
operating condition.
Labels
• UL/cUL Listed 1598 Luminaire
• UL/cUL Listed for Damp Location
• UL/cUL Listed for Wet Location –
Covered Ceiling
• UL/cUL Listed for Feed Through
• UL/cUL Listed for Direct Contact
with Insulation and combustible
material
IC and AIR-TITE™
Certified under ASTM-E283 and listed
UL/cUL 1598. May be used to meet
insulated ceiling and restricted
air-flow requirements such as:
• Washington State Energy Code
• International Energy Conservation
Code (IECC)
• New York State Energy Conservation
Construction Code (NY-ECCC)
• State of California Title 24 “Recessed
Luminaires in Insulated Ceilings.”
4-1/2"
[114mm]
5"
[127mm]
1/2"
[13mm]
8"
[203mm]
5-1/4"
[133mm]
4-1/2"
[114mm]
1/2"
[13mm]
7-1/8"
[181mm]
7-3/8"
[187mm]
13"
[330mm]
9-1/2"
[241mm]
ET400LVAT
4" Aperture, Non-IC,
New Construction, AIR-TITE,
12V Low Voltage, MR16
Specifications
• Thermally protected
Non-IC housing
• May be used ininsulated
ceilings but insulation
MUST be kept 3" from all
sides of fixture
• Integral 120V magnetic
transformer
• For use with 12V MR16
lamps
EI400LVAT
4˝ Aperture, IC,
New Construction, AIR-TITE,
12V Low Voltage, MR16
Specifications
• IC housing
• Housing may be covered
with insulation
• AIR-TITE housing prevents
airflow between attic and
living areas
• Integral 120V magnetic
transformer
• For use with 12V MR16
lamps