Specifications

5"/6" LED Recessed
Retrofit
77
DIMENSIONS
DESCRIPTION
RL706830E26WBS
5-Inch / 6-Inch LED
Recessed Retrofit
Replacement Lamp
Module-Trim with
E26 Medium Screw-base
Specifications
• For use in insulated
ceiling and non-insulated
ceiling rated housings
• High efficacy LED with
integral driver -
dimmable
The All-Pro RL706830E26WBS is a
retrofit LED Module-Trim for 5” and
6” aperture recessed downlights.
The RL706830E26WBS is designed
for use with compatible 5” and 6”
housings including the Halo H25,
H5, H27, H7, H7U series and All-Pro
ET/EI500, ET/EI2700, ET/EI700. The
RL7 with integral LED driver offers
120 volt dimming capability.
The RL7 lens provides uniform
illumination and wet location
listing. The RL7 die-cast
construction makes any
housing AIR-TITE for added HVAC
savings and code compliance.
MECHANICAL
Module Trim
• Module construction includes
LED, heat sink, reflector, lens,
baffle and trim ring
• Durable die-cast aluminum
construction
• Heat sink designed to conduct
heat away from the LED
keeping the junction
temperatures below specified
maximums, even when
installed in insulated ceiling
environments
• High Gloss Appliance White paint
finish
Lens
• Impact-resistant polycarbonate
• Convex form for lamp-like
appearance
• High lumen transmission
• Diffusing for even illumination
MOUNTING
Torsion Spring Brackets
• Precision formed steel torsion
spring brackets secure torsion
springs to fit compatible housings
with torsion spring mounting tabs.
• Ac c e s sory ( inc luded): 5" & 6"
Friction Blade Kit: Stainless steel
friction blade provide alternative
to torsion springs for retrofit in 5"
and 6" housings without torsion
spring mounting tabs.
• Friction blade design allows
the RL7 to be installed in any
position within the housing
aperture (360 degrees).
LED
• 636 lumens
• Color Temperature: 3000°K
• CRI: 81
• Lumen Maintenance: L70/50
70% lumens / 50,000 hours
• Efficacy 43.47 Lumens per Watt
• LED is a chip on board design
consisting of a multiple LED
package to create one virtual
light source for a productive
“cone of light”
ELECTRICAL
Power Connections
• E26 medium screw-base
Edison connector provides
easy retrofit of incandescent
housings.
Ground Connection
• Separate grounding cable
included on the RL7 module
for attachment to the housing
during installation.
LED Driver
• Dimmable driver is a120 Volt,
high efficiency, electronic
power supply providing DC
power to the LED.
• Driver meets FCC EMI/RFI
Consumer Level limits for use
in residential and commercial
installations.
• Driver features power factor
> .90, THD < 20% and has
integral thermal protection in
the event of over temperature
or internal failure.
• Driver is specifically designed
for compatibility with RL7
series LED.
• Driver mounts externally to
the module, allowing future
replacement, if needed.
Dimming
• The RL7 LED is dimmable to
15% with standard 120V
electronic low voltage dimmers
(recommended), and many
incandescent / magnetic low
voltage dimmers; and dims to
5% using dimmers with low end
trim adjustment.
• Note: Standard incandescent
dimmers require a minimum
load of typically >40 watts on the
circuit for full range dimming
performance (four LED modules).
• Note: For dimming with digital
(smart) multi-location dimmers
or when dimming fewer than
four LED modules, electronic low
voltage dimmers are required
(ELV dimmers need a neutral
connection in the wallbox).
• Refer to specification sheets
online for dimming information,
and refer to dimmer
manufacturers for compatibility.
Warranty
Cooper Lighting provides a three
year limited warranty on RL7 LED.
COMPLIANCE
Labels
• UL/cUL Listed
• UL/cUL Listed for Damp Location
• UL/cUL Listed for Wet Location
Covered Ceiling
• May be installed in housings
in direct contact with
airpermeable insulation and
combustible material
Qualification
• Can be used for International
Energy Conservation Code
(IECC) high efficacy luminaire
compliance
IC and AIR-TITE™
Certified under ASTM-E283 and
listed UL/cUL 1598. With compatible
housings, may be used to meet in-
sulated ceiling and restricted air-flow
code requirements.
Housing Compatibility
RL706830E26WBS UL/cUL Listed for
installation in the following Halo
and All-Pro E26 screw based 5" and
6" standard and shallow recessed
housings:
HALO: H7ICAT, H7RICAT, H7ICT,
H7RICT, H7ICATNB, H7ICTNB, H7T,
H7RT, H7TNB, H7TCP, H7UICT,
H7UICAT, H27ICAT, H27RICAT,
H27ICT, H27RICT, H27T, H27RT,
H5ICAT, H5RICAT, H5T, H5RT,
H25ICAT
All-Pro: EI500AT, EI500RAT, ET500,
ET500R, EI700AT, EI700RAT,
EI700ATNB, EI700, EI700R,
EI700ATNB, EI700NB, ET700,
ET700R, EI700U, EI700UAT,
EI2700AT, EI2700, EI2700R, ET2700,
ET2700R
RL7LED has UL classified listing
with other housings - see
specifications online at
www.cooperlighting.com.
Note: Some units may have
different features.
Visit www.cooperlighting.com for more information on the complete ALL-PRO Stock and
Specification offering. Product availability subject to change without notice.
7-1/4"
[184mm]
3-7/16"
[87mm]
Min. Starting Temp
-30°C (-22°F)
Sound Rating: Class A
EMI/RFI: FCC Title 47 CFR, Part 15,
Class B (Consumer)
Maximum IC (Insulated Ceiling) Ambient
Continuous Operating Temperature: 25°C (77°F)
Maximum Non-IC (NON-Insulated Ceiling)
Ambient Continuous Operating Temperature:
40°C (104°F)
Input Frequency:
50/60Hz
Power Factor: >0.90
THD: <20% Input Voltage: 120V
Rated Wattage:
15W max.
Input Power: 14.5W
Input Current: 121mA
Driver Compliance: UL60950, LPS rated
LED Lighting Data
Lumens: 636
Correlated Color Temperature (CCT): 3000K
Color Rendering Index (CRI, Ra): 81
Lumens per watt: 43.47
Energy Date (Typical)
TM