Specifications

6" LED Recessed
Retrofit
76
DIMENSIONS
7-1/4"
[184mm]
3-7/16"
[87mm]
DESCRIPTION
The All-Pro RL706830WBS LED
Module-Trim is for use with Halo
H750 LED series 6” aperture
recessed housings. The
RL706830WBS includes a dedicated
LED connector for California Title-24
compliance using a non-screw base
socket, and for where a non-screw
base high-efficacy luminaire is
required. The RL7 with integral LED
driver offers 120 volt dimming
capability. The RL7 lens provides
uniform illumination and wet
location listing. The RL7 die-cast
construction makes any housing
AIR-TITE for added HVAC savings
and code compliance.
MECHANICAL
Module Trim
• Module construction includes
LED, heat sink, reflector, lens,
baffle and trim ring
• Durable die-cast aluminum
construction
• Heat sink designed to conduct
heat away from the LED
keeping the junction
temperatures below specified
maximums, even when
installed in insulated ceiling
environments
• High Gloss Appliance White paint
finish
• High Gloss Appliance White
paint finish
Lens
• Impact-resistant polycarbonate
• Convex form for lamp-like
appearance
• High lumen transmission
• Diffusing for even illumination
MOUNTING
Torsion Spring Brackets
• Precision formed steel torsion
spring brackets secure torsion
springs to fit compatible housings
with torsion spring mounting tabs.
• Accessory ( included): 5" & 6"
Friction Blade Kit: Stainless steel
friction blade provide alternative
to torsion springs for retrofit in 5"
and 6” housings without torsion
spring mounting tabs.
• Friction blade design allows
the RL7 to be installed in any
position within the housing
aperture (360 degrees).
Housing Compatibility
RL706830WBS LED Retrofit
Module is listed with HALO H750
Series housings: H750ICAT,
H750RICAT, H750T, H750TCP
LED
• 636 lumens
• Color Temperature: 3000°K
• CRI: 81
• Lumen Maintenance: L70/50
70% lumens / 50,000 hours
• Efficacy 43.47 Lumens per Watt
• LED is a chip on board design
consisting of a multiple LED
package to create one virtual
light source for a productive
“cone of light”
ELECTRICAL
Power Connections
• LED connector is a non-screw
base luminaire disconnect
offering easy installation with
the matching Halo H750 Series
housings.
• Connector meets California
Title-24 high-efficacy
luminaire requirement for a
non-screw base socket, and
where required to qualify as a
high-efficacy luminaire.
• HE26LED adapter available
(order separately) if needed to
accommodate a standard
screw base ICAT housing
Ground Connection
• Separate grounding cable
included on the RL7 module
for attachment to the housing
during installation.
LED Driver
• Dimmable driver is a120 Volt,
high efficiency, electronic
power supply providing DC
power to the LED.
• Driver meets FCC EMI/RFI
Consumer Level limits for use
in residential and commercial
installations.
• Driver features power factor
>.90, THD <20% and has
integral thermal protection in
the event of over temperature
or internal failure.
• Driver is specifically designed
for compatibility with RL7
series LED.
• Driver mounts externally to
the module, allowing future
replacement, if needed.
Dimming
• The RL7 LED is dimmable to 15%
with standard 120V electronic
low voltage dimmers
(recommended), and many
incandescent / magnetic low
voltage dimmers; and dims to
5% using dimmers with low end
trim adjustment.
• Note: Standard incandescent
dimmers require a minimum
load of typically >40 watts on
the circuit for full range dimming
performance (four LED modules).
• Note: For dimming with digital
(smart) multi-location dimmers
or when dimming fewer than
four LED modules, electronic low
voltage dimmers are required
(ELV dimmers need a neutral
connection in the wallbox).
• Refer to specification sheets
online for dimming information,
and refer to dimmer
manufacturers for compatibility.
Warranty
Cooper Lighting provides a
three year limited warranty on
RL7 LED.
COMPLIANCE
Labels
• UL/cUL Listed
• UL/cUL Listed for Damp
Location
• UL/cUL Listed for Wet
Location – Covered Ceiling
• May be installed in housings
in direct contact with
air-permeable insulation and
combustible material
Qualification
• Can be used for State of
California Title 24 high efficacy
luminaire compliance
• Can be used for International
Energy Conservation Code
(IECC) high efficacy luminaire
compliance
IC and AIR-TITE™
Certified under ASTM-E283 and
listed UL/cUL 1598. With compatible
housings, may be used to meet
insulated ceiling and restricted
air-flow code requirements.
Accessories
(Order Separately)
HE26LED=Screw base
adapter
HE26LED24PK=Screw base
adapter, 24 pack
Note: Some units may have
different features.
Visit www.cooperlighting.com for more information on the complete ALL-PRO Stock and
Specification offering. Product availability subject to change without notice.
RL706830WBS
6-Inch LED
Recessed Retrofit
Replacement Lamp
Module-Trim with
Dedicated LED High-Efficacy
Connector
Specifications
• For use with Halo H750
series LED housings
• For use in insulated ceiling
and non-insulated ceiling
rated housings
• High efficacy LED with
integral driver - dimmable
Energy Date (Typical)
Min. Starting Temp
-30°C (-22°F)
Sound Rating: Class A
EMI/RFI: FCC Title 47 CFR, Part 15,
Class B (Consumer)
Maximum IC (Insulated Ceiling) Ambient
Continuous Operating Temperature: 25°C (77°F)
Maximum Non-IC (NON-Insulated Ceiling)
Ambient Continuous Operating Temperature:
40°C (104°F)
Input Frequency:
50/60Hz
Power Factor: >0.90
THD: <20% Input Voltage: 120V
Rated Wattage:
15W max.
Input Power: 14.5W
Input Current: 121mA
Driver Compliance: UL60950, LPS rated
LED Lighting Data
Lumens: 636
Correlated Color Temperature (CCT): 3000K
Color Rendering Index (CRI, Ra): 81
Lumens per watt: 43.47
TM