Technical Specifications

Specifications and dimensions subject to change without notice.
Sure-Lites • Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 • TEL [phone] • FAX [phone]
TECHN I C AL DATA
Lamps
The AP Series Exits with Heads use energy
efficient, long life LED’s to provide uniform
diffuse illumination of the exit face. The low
operating costs and zero maintenance
requirement makes LED lamps the wisest choice
for exit signs today. Emergency exit illumination
is provided by LED lamps and the heads employ
3.6V, .78W DC Long Lasting LED Heads.
Housing Construction
Rugged, durable, injection molded
thermoplastic materials are used throughout the
AP Series Exits with Heads. All structural
components are designed with reinforcing ribs
to add additional rigidity and to maximize
structural integrity. These materials are impact
and scratch resistant, and they have been UV
stabilized to resist discoloration due to age and
ultraviolet radiation. All components are
designed to be of snap-fit construction - no
mechanical fasteners - to facilitate installation in
under 5-minutes. Any components required for
installation (wirenuts, wire leads, universal
metal J-box bracket, etc.) are all included with
each exit. The universal design of the AP Series
Exits with Heads enables universal exits to be
configured as single face or double face in the
field. The AP Series Exits with Heads can be
wall, ceiling, or end mounted; a rugged, snap-fit,
low profile canopy with captive screws is
included with every exit for ceiling and end
mounting applications.
Lens
Lenses for the AP Series Exits with Heads are
made from durable impact resistant
thermoplastic. All exit faces are designed with
full 3/4” stroke snap-out or snap-in chevron
directional indicators to insure maximum
visibility and compliance with the latest codes.
Line-Latch e d
All Pro’s line-latched electronic circuitry makes
installation easy and economical. A labor
efficient AC activated load switch prevents the
lamps from turning on during installation to a
non-energized AC circuit. Line-latching
eliminates the need for a contractor’s return to a
job site to connect the batteries when the
building’s main power is turned on.
Solid-State C h a rger
Supplied with a 120/277 VAC, voltage regulated
solid-state charger. Immediately upon
restoration of AC current after a power failure,
the charger provides a high charge rate. The
charge circuit reacts to the condition of the
battery and regulates the charging process in
order to maintain peak battery capacity and
maximize battery life. Solid-state construction
recharges the battery following a power failure
in accordance with UL 924.
Brow n o u t Circuit
The brownout circuit on All Pro’s exits monitors
the flow of AC current to the exit and activates
the emergency lighting system when a
predetermined reduction of AC power occurs.
This dip in voltage will cause most ballasted
fixtures to extinguish causing loss of normal
lighting even though a total power failure has
not occurred.
Solid-State Transfer
The AP Series Exits with Heads incorporates
solid-state switching which eliminates corroded
and pitted contacts or mechanical failures
associated with relays. The switching circuit is
designed to detect a loss of AC voltage and
automatically energizes the lamps using DC
power. Upon restoration of AC power, the DC
power will be disconnected and the charger will
automatically recharge the battery.
Low Vo l t a ge Disconnect
When the battery’s terminal voltage falls, the
low voltage circuitry disconnects the lighting
load. The disconnect remains in effect until
normal utility power is restored, preventing
deep battery discharge.
Te s t Switch / Power Indicato r L i g h t
A test switch located on the bottom of the exit
permits the activation of the emergency circuit
for a complete operational systems check. The
Power Indicator Light provides visual assurance
that the AC power is on.
Overload and Short C i rcuit
Prote c t i o n
The solid-state overload monitoring device in
the DC circuit disconnects the lamp load from
the battery should excessive wattage demands
be made and automatically resets when the
overload or short circuit is removed. This
overload current protective feature eliminates
the need for fuses or circuit breakers for the DC
load.
Sealed Nickel Cadmium Ba t tery
All Pro Emergency sealed nickel cadmium
batteries are maintenance-free with a life
expectancy of 15 years. The sealed rechargable
nickel cadmium battery offers high discharge
rates and stable performance over a wide range
of temperatures. The specially designed
resealable vent automatically controls cell
pressure, assuring safety and reliability. This
battery is best suited for harsh ambient
temperatures because the electrolyte is not
active in the electrochemical process.
Wa rra n t y
All Pro products are backed by a five-year
warranty.
S A M P L E N U M B E R : A P C 7 R
Family
APC7 = Self-Powered with LED All Pro Exit/Emergency with LED Heads
APCH7 = Self-Powered with LED All Pro Exit/Emergency with LED Heads,
High Power with remote capability
Face Options
__ = Universal
Letter Colors
R = Red
G = Green
ORDER I N G INF O R MATION
APC / APCH SERIES EXITS WITH LED HEADS COMBO
ADX110025 pc
2012-06-11 11:09:40