Cut Sheet

www.coopercontrol.com
203 Cooper Circle, Peachtree City, GA 30269
P: 800-553-3879 F: 800-954-7016
Cooper Controls, Greengate, Novitas, Yes Box, PCI Lighting Control Systems, VisionTouch, VisionSwitch,
MicroSet, Digita, ControlKeeper, LiteKeeper, TracKeeper, IntelliRelay are valuable trademarks of Cooper
Industries in the U.S and other countries. You are not permitted to use Cooper Trademarks without the
prior written consent of Cooper Industries.
OXC, Extreme Temperature Sensors
WiringDiagrams
Coverage
OXC-P-2MH0-R
OXC-P-1500-R
Mounting
SurfaceMount
2S Box Mounting
4S Box Mounting
Mounting
Post
SENSOR: The sensor mounts to normal ceiling tile through a 3/4” hole. The threaded mounting
post may be cut down if it is too long to fit into the junction box. The sensor may also be surface
mounted or mounted to a standard NEMA 2S or 4S junction box.
CAUTION:Finger-tightenthenuttoavoidstrippingthemountingpost.Donotapply
pressure to Fresnel lens.
BACKPLATE: The sensor can be easily snapped onto or pulled away from the backplate without
disturbing the mounting hardware. To pull the sensor away from the backplate, place your fingers
on the door on the front of the sensor and slide your fingers up onto the back end of the sensor,
with your fingers resting below the edge of the backplate. As you press against the sensor, use
your other hand to grip the opposite end of the sensor and pull it away from the backplate.
To snap the sensor back onto the backplate, place the end of the sensor without a door against
the backplate first, hooking the edge of the sensor on the two small prongs that extend from the
backplate. Press the other end of the sensor against the backplate until it snaps into place.
SWITCHPACK: Designed to be mounted externally to any junction box. When mounted, the line
connections are inside the box and the Class 2 wiring exits the rear of the Switchpack housing.
In areas where Class 2 wiring is not permitted, the Switchpack can be mounted internally to any
standard electrical box.
Light Level
(FC)
OFF
3
5
10
Switch No.
5 6
Measured at 30” off the ground.
1 - Time Delay
2 - Time Delay
3 - Time Delay
4 - Self Adjust Disable
5 - Ambient Lights
6 - Ambient Lights
7 - N/A
8 - Lighting Sweep
9 - N/A
10 - Manual Override
Time Delay
(Minutes)
0.25
6
10
14
18
22
26
30
Switch No.
1 2 3
DIPSWITCHSETTINGS
































4” Square
Box with
Mud Ring
1 Gang
Box with
Mud Ring
LOAD "A"
BLUE
NEUTRAL
HOT
**USE BLACK LEAD FOR 120 VAC.
USE ORANGE LEAD FOR 277 VAC.
CAP UNUSED LEAD.
LINE
**HOT
WHITE
BLUE
SWITCH-
PACK
BLACK (COMMON)
BLUE (CONTROL)
PURPLE (NORMALLY CLOSED)
GRAY (ISOLATED RELAY COMMON)
ORANGE (NORMALLY OPEN)
RED (10-30 VDC)
BLACK (COMMON)
BLUE (CONTROL)
RED (15 VDC )
AUTOMATIC MODE OPERATION:
1. WHEN SENSOR ACTIVATES, BOTH
LOADS TURN ON.
2. LOAD TURNS OFF, WHEN SENSOR
TIMES OUT.
RECOMMENDED WIRE:
18-3 AWG STRANDED WIRE SHIELDED OR
NON/SHIELDED
TO ADDITIONAL SENSORS.
MAXIMUM 5 SENSORS PER SWITCHPACK.
TO ADDITIONAL SWITCHPACKS.
MAXIMUM 10 SWITCHPACKS PER SENSOR.
*Wiring diagram for single sensor application.
Visit our website for other wiring diagrams.