User guide

COMMAND SUFFIX ITEM AFFECTED # CHAR SECTION
E 04 Set alarm mode - 7.2.2
G,P,R,W 04 Setpoint 4 value 6 11.16
X 04 Read time value 8 8.2.3
Z 04 Reset LATCHED setpoints - 8.2.3
E 05 Start (Batch mode only) - 8.2.3
G,P,R,W 05 Setpoint 5 value 6 11.17
Z 05 Power On reset (Hard reset) - 8.2.3
G,P,R,W 06 L1 CNF (Lockout byte 1) 2 11.1
G,P,R,W 07 L2 CNF (Lockout byte 2) 2 11.1
G,P,R,W 08 L3 CNF (Lockout byte 3) 2 11.1
R,W 09 MODE (operational mode) 2 11.2
G,P,R,W 0A CONFG 1 (Configuration 1) 2 11.4
G,P,R,W 0B CONFG 2 (Configuration 2) 2 11.5
G,P,R,W 0C CONFG 3 (Configuration 3) 6 11.6
G,P,R,W 0D CONFG 4 (Configuration 4) 2 11.7
G,P,R,W 0E AV.CNF (Average configuration only available
for rate or square-root rate)
2 11.8
G,P,R,W 11 Bat DP (Batch decimal point ) or
RTE DP (Rate decimal point)
2 11.13
G,P,R,W 12 B.LOAD (Batch load) or
RTE OF (Rate Offset)
6 11.14
G,P,R,W 13 BAT SC (Batch Scale) or
RTE SC (Rate Scale)
6 11.14
G,P,R,W 14 TOT DP (Total decimal point) 2 11.13
G,P,R,W 15 TOT OF (Total offset) 6 11.14
G,P,R,W 16 TOT SC (Total Scale) 6 11.14
G,P,R,W 17 AL TI (Alarm time) 4 11.11
G,P,R,W 18 GATE T (Gate time) 2 11.9
R,W 19 Baud rate 2 11.22
R,W 1A SER.CNF (Serial Communication Configuration) 2 11.23
G,P,R,W 1B DAT FT (Communication Bus Format) 2 11.24
G,P,R,W 1C BUS FT (Communications Bus Format) 2 11.25
G,P,R,W 1D ADDRES (RS-485 device # address) 2 11.26
G,P,R,W 1E SER TI (time between each transmission) 4 11.27
R,W 1F SET TI (Set time) 6 11.18
G,P,R,W 20 Pulsed setpoint number 2 11.10
G,P,R,W 21 Scale operator 2 11.15
G,P,R,W 22 Input Scale 6 11.12
G,P,R,W 23 Input Offset 6 11.12
G,P,R,W 24 Communication Recognition character 2 11.28
R,W 25 Communication Turnaround Delay 2 11.30
G,P,R,W 26 Output scale 6 11.19
G,P,R,W 27 Output Offset 6 11.20
G,P,R,W 28 Time value 6 11.21
G,P,R,W 29 Total raw value 8 11.21
G,P,R,W 2A Batch raw value (In Batch mode only) 8 11.21
G,P,R,W 2B # of Batches raw value (In Batch mode only) 6 11.21
G,P,R,W 2C Unit of measure #1 6 11.29
G,P,R,W 2D Unit of measure #2 6 11.29
R,W 2E Clock frequency calibration 2 11.31
R,W 2F Analog out Volt zero calibration 4 11.31
R,W 30 Analog out Volt span calibration 4 11.31
R,W 31 Analog out current zero calibration 4 11.31
R,W 32 Analog out current span calibration 4 11.31
G,P 33 Display mode 2 11.3
G,P,R,W 40 RAM or EEPROM Block A Batch: 76 Rate
(SQ RT): 78
11.32
CF 125 INFINITY SC GUIDE 20 M1519/N/0605