User guide

Command Suffix Item affected #Char Section
V 01 Read data string 0 8.2.3
X 01 Read unfiltered value 0 8.2.3
Y 01 Write value to display 6 8.2.3
Z 01 Reset latched alarms 0 8.2.3
D 02 Disable setpoints 1 and 2 0 8.2.3
E 02 Enable setpoints 1 and 2 0 8.2.3
R, W 02 L2 CNF, Lockout byte #2 2 10.1
U 02 Peak/Valley (HI/LO) status 0 8.2.3
X 02 Read peak (HI) value 0 8.2.3
X Y02 Write value to meter 7 8.2.3
Z 02 Reset averaging filter 0 8.2.3
D 03 Disable display of remote value 0 8.2.3
E 03 Set alarm mode 0 7.2.2
R, W 03 L3 CNF, lockout byte #3 2 10.1
U 03 Microprocessor Revision 0 8.2.3
X 03 Read valley (LO) value 0 8.2.3
Z 03 Soft reset (RESET1, from RAM) 0 8.2.3
D 04 Hold displayed value 0 8.2.3
E 04 Display “RUN” 0 8.2.3
R, W 04 L4 CNF, lockout byte #4 2 10.1
X 04 Read filtered value 0 8.2.3
Z 04 Hard reset (RESET2, from EEPROM) 0 8.2.3
D 05 Reset tare, valid only on strain meter 0 8.2.3
E 05 TARE, valid only on strain meter 0 8.2.3
G, P, R, W 05 INPUT, type and range 2 10.1
Z 05 Reset Peak/Valley (HI/LO) 0 8.2.3
G, P, R, W 07 RDG.CNF display controls 2 10.3
G, P, R, W 08 RDG SC, display scale factor 6 10.4
G, P, R, W 09 RDG OF, display offset 6 10.5
G, P, R, W 0A IN CNF, meter features 2 10.6
G, P, R, W 0B INP SC, input scale factor 6 10.4
G, P, R, W 0C DEC PT and CNT BY (roundoff) 2 10.7
G, P, R, W 0E FIL.CNF and FIL TI, filter #’s 2 10.8
G, P, R, W 10 SP CNF, control setpoints 1 and 2 2 10.9
G, P, R, W 11 AL CNF, control setpoints 3 and 4 2 10.10
G, P, R, W 12 AL FNC, alarm function 2 10.11
G, P, R, W 13 AL RDG, # readings delayed 2 10.12
R, W 14 SP DB, setpoint hysteresis 4 10.13
R, W 15 AL DB, alarm hysteresis 4 10.14
G, P, R, W 16 OUT.CNF, analog out and flashing 2 10.15
G, P, R, W 17 OUT SC, analog out scale 6 10.4
R, W 18 SER.CNF, communications configuration 2 10.16
G, P, R, W 1A ADDRES, RS-485 device # address 2 10.17
G, P, R, W 1B DAT FT, communication data format 2 10.18
G, P, R, W 1C BUS FT, communications BUS format 2 10.19
R, W 1D SER CNT, # of readings between each transmission 4 10.20
G, P, R, W 1E SER.RCG, recognition character 2 10.21
G, P, R, W 1F SER.UOM, units of measure 6 10.22
R, W 20 SER.DLY, communication turnaround delay 2 10.23
G, P, R, W 21 SP 1, setpoint 1 value 6 10.24
G, P, R, W 22 SP 2, setpoint 2 value 6 10.24
G, P, R, W 23 SP 3, setpoint 3 value 6 10.24
G, P, R, W 24 SP 4, setpoint 4 value 6 10.24
G, P, R, W 25 INP OF, input offset 6 10.5
G, P, R, W 26 OUT OF, analog output offset 6 10.5
CF 125 INFINITY SC GUIDE 18 M1519/N/0605