Submittal Sheet

DURA-BLOK Supports
DBE Series
Support Base with Rod Risers & Channel
• Base with (2)
1
/2” electro zinc all threaded rod risers - Top channel is 1” (25.4mm) tall.
See chart for adjustable height x wide x length.
• 100% recycled rubber, UV resistant.
• Load Rating* 200 lbs.
(0.89kN) (To increase load capacity use load distribution plate
CLDP10)
• DURA-BLOK DBE-Series channel support is designed as a superior support of piping
systems, cable tray, HVAC equipment and many other applications where elevation
adjustment is critical. The DURA-BLOK is UV resistant and suitable for installation on
any type of roofing material or other flat surfaces. (For pipe straps/clamps, rollers
and roller supports that can be used with these DURA-BLOK supports, see page 159)
* General Note: Consult roofing manufacturer or engineer for roof load capacity.
The weakest point may be the insulation board beneath the rubber membrane.
DBR Series
Support Base with Rod Risers & Pipe Roll
• Base with (2)
1
/2” electro zinc all threaded rod risers and a
B3114-3
1
/2 pipe roll with sockets - base is 4” (101.6mm) high x 6” (152.4mm)
wide x 9.6” (243.8mm) long. Overall height is 12” (304.8mm) from bottom of
base to contact point on roller.
• Pipe roll & sockets for up to 3
1
/2” (90) pipe sizes.
• 100% recycled rubber, UV resistant.
• Load Rating* 200 lbs.
(0.89kN) (To increase load capacity use load distribution plate
CLDP10)
• DURA-BLOK DBR-Series support is designed to support pipe up to 3
1
/2” (90) nominal
size where difference in elevation is required and longitudinal movement is
expected. The DURA-BLOK is UV resistant and approved for installation on any type
of roofing material or other flat surfaces.
Thickness x Width x Length Wt./Each
Part No.
In. mm Lbs. kg
CLDP10 11 Ga. x 1
5
/8” x 9
1
/2” (3.0 x 41.3 x 241.3) 0.53 (0.24)
Adjustable Height x Width x Length Wt./Each
Part No.
In. mm Lbs. kg
DBE10-8 5
1
/2-8” x 6” x 9.6” (139.7-152.4 x 152.4 x 243.8) 5.68 (2.58)
DBE10-12 5
1
/2-12” x 6” x 9.6” (139.7-304.8 x 152.4 x 243.8) 5.72 (2.59)
DBE10-16 5
1
/2-16” x 6” x 9.6” (139.7-406.4 x 152.4 x 243.8) 5.76 (2.61)
CLDP10
Load Distribution Plate
• 11 ga. (3.0mm) steel plate with slots.
• Dimensions: 1
5
/8” (41.3mm) wide x 9
1
/2” (241.3mm) long.
• DURA-BLOK CLDP10 load bearing stabilizer plate increases load ratings
for DBE Series and DBR Series by allowing the load from the threaded
rods to be distributed over the length of the base instead of the point
load where the rods attach to the base.
Adjustable Height x Width x Length Wt./Each
Part No.
In. mm Lbs. kg
DBR10-12 up to 12” x 6” x 9.6” (up to 304.8 x 152.4 x 243.8) 8.20 (3.72)
Loosen hex nuts
and slide plate
under the flat
washers
Retighten the hex
nuts with plate in
place
Reference page 153 for general fitting and standard finish specifications.
DURA-BLOK
™
Rooftop Supports
156
Strut Systems