Specification Sheet
B
D
C
E
A
(Rod Size)
Hanger Rod
and Nuts Not
Included
D
Center of pipe to
center of axle.
E
Center of axle
to bottom
of socket.
Size Range: 2" (25mm) thru 30" (750mm) pipe
Material: Cast iron and steel axle
(Non-metallic polyurethane rollers are available)
Function: For supporting pipe where expansion may occur due to
thermal movement. Double rod design provides support for greater loads.
Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A,
Type 42, 2"
(50mm) thru 24" (600mm), and Manufacturers Standardization
Society ANSI/MSS SP-69 & SP-58, Type 41
Note: When pipe line is insulated, total outside diameter of pipe and covering
should be used to determine size of hanger; also see B3160 to B3165 on
pages 157 thru 162.
Finish: Plain. Contact customer service for alternative finishes and materials.
Order By: Part number, pipe size and finish
Note: Not for continuous cycling applications.
B3114 - Pipe Roll with Sockets
36" (900) available
upon request.
Pipe Size Rod Size BCD
Part No.
in. (mm) A in. (mm) in. (mm) in. (mm)
B3114-2 2" (50)
3
/8"-16 2
5
/8" (66.7) 4
1
/8" (104.8) 1
9
/16" (39.7)
B3114-2
1
/2 2
1
/2" (65)
1
/2"-13 3
1
/8" (79.4) 4
7
/8" (123.8) 1
7
/8" (47.6)
B3114-3 3" (80)
1
/2"-13 3
3
/4" (95.2) 5
1
/2" (139.7) 2
3
/16" (55.6)
B3114-3
1
/2 3
1
/2" (90)
1
/2"-13 4
1
/4" (107.9) 6
1
/8" (155.6) 2
1
/2" (63.5)
B3114-4 4" (100)
5
/8"-11 4
3
/4" (120.6) 6
3
/4" (171.4) 2
3
/4" (69.8)
B3114-5 5" (125)
5
/8"-11 5
13
/16" (147.6) 8
1
/16" (204.8) 3
3
/8" (85.7)
B3114-6 6" (150)
3
/4"-10 6
7
/8" (174.6) 9
9
/16" (242.9) 3
15
/16" (100.0)
B3114-8 8" (200)
7
/8"-9 8
7
/8" (225.4) 11
15
/16" (303.2) 5
1
/16" (128.6)
B3114-10 10" (250)
7
/8"-9 11" (279.4) 14
1
/16" (357.2) 6
1
/4" (158.7)
B3114-12 12" (300)
7
/8"-9 13" (330.2) 15
13
/16" (401.6) 7
3
/8" (187.3)
B3114-14 14" (350) 1"-8 14
1
/4" (361.9) 17
3
/4" (450.8) 8
1
/4" (209.5)
B3114-16 16" (400) 1"-8 16
1
/4" (412.7) 19
3
/4" (501.6) 9
1
/4" (234.9)
B3114-18 18" (450) 1"-8 18
1
/4" (463.5) 21
7
/8" (555.6) 10
3
/8" (263.5)
B3114-20 20" (500) 1
1
/4"-7 20
1
/4" (514.3) 24
1
/4" (615.9) 11
1
/2" (292.1)
B3114-24 24" (600) 1
1
/2"-6 24
1
/4" (615.9) 28
7
/8" (733.4) 13
13
/16" (350.8)
B3114-30 30" (750) 1
1
/2"-6 30
1
/4" (768.3) 35
1
/2" (901.7) 17
1
/4" (438.1)
E Max. O.D. Covering Design Load Approx. Wt./100
Part No.
in. (mm) in. (mm) Lbs. (kN) Lbs. (kg)
B3114-2
3
/4" (19.0) 3
3
/4" (82.5) 600 (2.67) 119 (54.0)
B3114-2
1
/2
3
/4" (19.0) 3
3
/4" (95.2) 660 (2.93) 140 (63.5)
B3114-3
3
/4" (19.0) 4
1
/2" (114.3) 700 (3.11) 158 (71.6)
B3114-3
1
/2
3
/4" (19.0) 5" (127.0) 750 (3.33) 170 (77.1)
B3114-4
3
/4" (19.0) 5
7
/8" (149.2) 750 (3.33) 188 (85.3)
B3114-5
3
/4" (19.0) 7" (177.8) 750 (3.33) 246 (111.6)
B3114-6 1
1
/8" (28.6) 8
1
/4" (209.5) 1070 (4.76) 504 (228.6)
B3114-8 1
1
/8" (28.6) 10
1
/2" (266.7) 1350 (6.00) 658 (298.4)
B3114-10 1
1
/8" (28.6) 12
3
/4" (323.8) 1730 (7.69) 849 (385.1)
B3114-12 1
1
/8" (28.6) 14
3
/4" (374.6) 2400 (10.67) 1200 (544.3)
B3114-14 1
1
/2" (38.1) 16
1
/4" (412.7) 3130 (13.92) 2289 (1038.3)
B3114-16 1
1
/2" (38.1) 18" (457.2) 3970 (17.66) 2497 (1132.6)
B3114-18 1
1
/2" (38.1) 20
1
/4" (514.3) 4200 (18.68) 2899 (1315.0)
B3114-20 1
1
/2" (38.1) 22
1
/2" (571.5) 4550 (20.24) 3637 (1649.7)
B3114-24 2" (50.8) 26
1
/2" (673.1) 6160 (27.40) 5664 (2569.2)
B3114-30 2" (50.8) 32
1
/2" (825.5) 7290 (32.42) 9437 (4280.6)
Notes: If using D.I. pipe refer
to page 307 for sizing.
Non-metallic rollers with
hot-dip galvanized sockets
and stainless steel hardware
are available for most sizes
(B3114NM-Pipe Size). Contact
Eaton Engineering for more
information.
Pipe Rollers &
Pipe Supports
Pipe Rollers & Roller Supports
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
109
B-Line series Pipe Hangers & SupportsEaton