Ver 1.
CONTENTS 1. Product Overview ............................................................................................ 02 1.1 Specifications .................................................................................................... 02 1.2 Diagram.............................................................................................................. 02 1.3 Part List .............................................................................................................. 03 1.
1. Product Overview 1.1 Specifications Available Color Chassis:Silver , Bezel:Black Dimensions (W)266mm x (H)598mm x (D)628mm Material Chassis:STEEL M/B Type Extended ATX, ATX Appearance:AL 5.25" Drive Bay 5 Exposed (without the use of exposed 3.5" Drive bay) 4 Expose (with the use of one 3.5" Drive bay) 3.5" Drive Bay 6 Hidden; 1 Exposed (converted from one 5.
1.3 Part List 1 16 17 2 Exclusive Giveaway 3 CM Accessory Box 4 15 5 14 6 13 7 Item 1 2 3 4 5 6 7 8 9 8 11 9 10 Parts Name Top Cover Rear Fan 120x25mm Top Fan 120x25mm Filter (Rear) Side Fan 120x25mm Left Side Panel Shutter Fan Cover Bottom Fan 120x25mm Fan Holder Q'ty 1 1 2 1 1 1 1 1 1 Item 10 11 12 13 14 15 16 17 12 Parts Name HDD Tray Filter (Front) 5.25'' Shield Front Door FDD-Bracket Right Side Panel CM Accessory Box Casing Q'ty 6 1 5 1 2 1 1 1 1.
2. Installation Guide Note: The sequence of installation may differ depending on the type of case and devices used. 2.1 How to remove the Side Panel and install the Power Supply.
2.2 How to install the Motherboard. Note: If the I/O plate of the case does not fit your motherboard,please remove the I/O plate and replace it with the one provided with the motherboard. 1 Align the stand-off holes of M/B with MB tray and screw the stand-offs. 2 Make sure the holes on the Motherboard and chassis line up completely before securing the screws. #6-32 Stand-off (16.9mm) for Extend ATX M/B Stand-off (6.5mm) for ATX M/B 2.3 How to install the add-on cards.
* Insert the device into 5.
* Installation of IDE and SATA Hard Drives 1 2 3 2.
* Install the rear fan (Optional item) * Install the HDD fan (Optional item) 1 2 2.6 How to clean the filter 2.7 Change the opening direction of the front panel 1 3 2 Press Down Push up to remove hinge.
4 5 6 Remove hinges and insert into other side 7 8 Switch the magnet and screw to the opposite side. Replace door - it should now open from the opposite direction.
2.8 Cable Management SATA SATA Power Wire Power Wire 2.
3. I/O Function Panel Installation Guide Please refer to the illustration in the section of USB2.0, IEEE 1394a, eSATA and Audio connector from the motherboard user manual. Please select the motherboard which uses the same USB2.0, IEEE1394, eSATA, AC’97,HD Audio standard as below; otherwise, it will cause damages to device(s). The following illustration is a connection diagram for the front panel I/O cable. NEVER connect an IEEE1394 cable to the USB2.0 connector. Doing so will damage the device.
4.
A1:(2-Pin Thermal Sensor Connector) A2:(2 Pin Header) B1:(4 Pin USB Connector) B2:(USB Pin Header on Controller Board) C1:(4 Pin Power Connector) C2:(4 Pin 12V Power Header) D1:(4 Pin PWM Fan Connector) D2:(4 Pin PWM Fan Header) LED 1 lights once the temp. of GPU is higher than the thermostatic setting. LED 2 lights once the temp. of Intake is higher than the thermostatic setting.
510003300-GP
