PREPARATION Unpacking and Installation Open the package. Take out the TV. Install the TV stands. ~~ Connect tha power card, Standard Accessories 2 Batteries Re mate Control 4 Screws 2 Base Stands Quick Start Guide Warranty Card Stand Installation Step 1: Take out the TV and carefully put It {screen downward) on a stable and fiat table with a soft cloth pincushion it, Step 2; Plasma check to aka sure thees are the same mark (L/R} on the TV back and the correct stand.
WARNING AND PRECAUTION Read all of the Instructions before operating the set. Keep these Instructions for later use. Important Safety Instructions ® Read these Instructions All the safety and operating instructions should be read before this product is operated. ® Keep these instructions The safety and operating instructions should ba retained for future reference. # Head all warnings — All wakings on the appliance and In the operating Instructions should be adhered to.
For the terminals marked with symbol of "4" may be of sufficient magnitude to constitute a risk of crestless shook, The external wiring connected to the terminals requires installation by an instructed person or the use of ready-made leads or cords. To prevent injury, use the bracket to securely install this apparatus on the table/wall In accordance with the Installation Instructions. Danger of explosion If battery Is Incorrectly replaced. Replace only with the same or equivalent type.
WERE Directive Correct Disposal of this product. This marking Indicates that this product should not be wo disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, rectos It responsibly to mmm promote the sustainable reuse of material resources.
® Disconnect the power before moving or Installing the TV. Otherwise electric shock may occur. Remove the stand before installing the TV on a wall mount by performing the stand attachment in reverse. If you Install the TV on a selling or slanted wall, It may fall and tracksuit In severe Injury. Use an authorized wall mount and contact the local dealer ar qualified personnel. Otherwise It Is not covered by the warranty. Do not over tighten the screws as this may cause damage to the TV and void your warranty.
Taking back old appliances (Germany: Take-back obligation of distributors) Distributors with a sales area for factorial and electronic equipment of at least 400 square meters and distributors of foodstuffs with a total sales area of at least 800 square tetras who offer and make available on the market electrical and astronomical equipment several times In a calendar year or ana permanent basis are obliged to take back free of charge an ald appliance of the end user of the same type of equipment when handing
TERMINAL CONNECTION Terminal Connection Description ANTENNA IN Conn act a coaxial cable to receive signals from the antenna, cabs or italics. VAIN Connect audit and video signal from signal source such as DVD. use USB port. HDMI Connect HDMI Input signal from signal source such as DVD. Use a coaxial (or an optical) cable to output your TV audio DIGITAL AUDIO OUT signal to a compatible audio receiver. cl Cl card part. LAN Wired network port.
REMOTE CONTROL “Usa the Power button to tur on or tum off the TV, “TV will ba In motive standby for about 15 minutes after a Power button press to turn off the TV. The TV will enter passive standby after this time. On a Power button press to tum on the TV, the TV will resume Instantly If In active standby or will take few seconds longs fin passive standby. 2. GUIDE: Access tha Electronic Program Guide. 3. Application Buttons: Access specific applications quickly and directly. 4.
BASIC OPERATION Turn on or turn off the TV 1. Connect the paws card to the TV and wall auntie. 2. In standby mads, press POWER button an the remote control to tum an the TV. . In working status, press POWER button on the remote contra to turn off the TV. &. If you want to paws off the TV completely, please pull out the power cord from the wall auntie. TV Control Button In standby mode: Short press TV control button to tum on the TV.
TROUBLE SHOOTING Before calling a services technician, please check the following table fur a possible cause of the symptom and some solutions. General Problem/Solution = Remote control sows not work Change the batteries. Check if batteries are install led correctly. Check if main power Is connected. Check if there are some tams between remote sensor and Ramos control. + Poor Sign This is usually caused by interference from electrician equipment or radio interference sources.
SPECIFICATION Working voltage: Dimensions without stand (WXHXD): Net weight without stand: RF aerial Input: Language of 08D: System: Channel cave! Environment {only for Tropical climates zone's: Environment (only for Moderate climates zone): LICENSE Homer Administrator, Inc. 100-240V~ 50/60 Hz 423.4 X77.6 mm 75 ohm unbalanced Multiple opticians.
RADIO MODULE Wireless Network Frequency Band Transmitting 240: 2412~2472 MHz 50: Band I: 5180~5240 MHz Band II: 5260-5320 MHz Band Ii; 5500-5700 MHz <20dBm Remark: 1). The device should be positioned or operated at least 20cm away farm the user. 2). Due to various sales regions, the wireless module may have different configurations which will not exceed the maximum described In this manual. 3). Restrictions or Requirements in following countries: Indoor use only within 5150-5350MHz.
