Owner manual

www.hysecurity.com Display Menu D0536 Rev. B 3-9
Installer Menu Setting Options Menu Tasks & Explanations SDC Wire
Connections
OR1REVERSE
OuterArmLoop
0=Pauseclosingonly
1 = Enable reversing to open
2=Ignoreandcontinueclosing
The default is for full reversal when the Inner
ArmingLoopistriggered.Asettingof0causes
the barrier arm to only pause when triggered.
Closure begins as soon as the loop is clear again.
Asettingof2isprovidedforthemostsecure
facilities where it is essential that the loop trigger
is completely ignored and the barrier arm contin-
ues closing without pause or reversal.
OUT OBS LOOP
(OUTERARMING)
COM or connection
toHY-5Adetector
IR1REVERSE
InnerArmLoop
0=Pauseclosingonly
1 = Enable reversing to open
2=Ignoreandcontinueclosing
The default is for full reversal when the Inner
ArmingLoopistriggered.Asettingof0causes
the barrier arm to only pause when triggered.
Closure begins as soon as the loop is clear again.
Asettingof2isprovidedforthemostsecure
facilities where it is essential that the loop trigger
is completely ignored and the barrier arm contin-
ues closing without pause or reversal.
IN OBS LOOP
(INNERARMING)
COM or connection
toHY-5Adetector
DL1STANDARD
Detector Logic
1 = Standard
2=QuickClose
Conguresforfasterclosure.Thisselection
determines whether the close timer begins to
count after vehicles have departed the detector
loops or whether the close timer will count down
while the loops are occupied.
Thedefaultsetting1causestheCloseTimerto
startwhentheCenterLoopisclear.Asettingof
2 causes the Close Timer to start when the open
limit switch trips.
Center Loop
COM or connection
toHY-5Adetector
CR0REVERSE
Center Loop
0 = Reopen if center loop triggers
1=Pauseonly
The default allows the barrier arm to reopen if
the Center Loop detector is triggered during
closureofthebarrierarm.Asettingof1causes
the barrier arm to only pause when triggered.
Closure begins as soon as the loop is clear again.
Center Loop
COM or connection
toHY-5Adetector
CB 0 (OFF)
CLDDisableELD
0 = Normal operation of Free Exit
1=DisableFreeExit
Setting1allowsanCLDinputtodisabletheFree
ExitDetector(ELD)untilthebarrierarmisfully
closed.Usedinbi-directionaltrafcsituations.
Center Loop
COM or connection
toHY-5Adetector
CP 0 (OFF)
CLD Counts PBO
0 = Immediate closure
1=Providesaddt’lopentime
The default allows the Center Loop Detector
when triggered and released, to close the barrier
armimmediately.Theoptionalsettingof1des-
ignates that the Smart DC Controller remember
an additional open command if the open input
is activated a second time while the barrier arm
remains open. (For example, to prevent a vehicle
from being stranded).
Center Loop
COM or connection
toHY-5Adetector
EB0(OFF)
ELDBackoff
0 = Normal operation of Free Exit
1=Backoffclosefunction
The default allows normal latch open operation
oftheFreeExitdetector.Theoptionalsettingof
1,createsanautomaticclosefunctionifavehicle
triggersandthenbacksofftheFreeExitLoop
detector.
FreeExitLoop
COM or connection
toHY-5Adetector
RL10DISABLED
Relay1Logic
0 = Disabled
1to38available
ConguresthefunctionoftheUser1output
relay.IthasthecapacitytoswitchbothACand
DC loads and can be used for high voltage and/
or high current loads. Connect devices directly to
the top of the relay: COM and either NO and/or
NC contacts.
Multiple logic function options exist. See “User
Relays - Programming Procedure” on page 6-8.
COM
User1Relay