INSTRUCTION MANUAL DIGI-LOCK Keyless Entry System Installation Programming Troubleshooting BASE Industries 2
425 Pomona Rd. Corona, CA. 92880 Revision F TABLE OF CONTENTS OWNER REGISTRATION CARD INTRODUCTION Product Overview……………………………… System Dimensions………………………….. Safety Guidelines…………………………….. 1 1 2 INSTALLATION Mounting The System……………………….. Grounding The System………………………. Powering The System………………………… Basic Wiring Connections…………………… Wiring Diagrams………………………………. Circuit Board Diagram……………………….. Auxiliary Open Wiring Connections………… Time Clock Wiring Connections…………….. Slave Keypad Wiring Diagram……………….
BASE Industries 2425 Pomona Rd. Corona, CA. 92880 installed a minimum of 10 feet away from any gate or gate operator. Always instruct the end user on safe, proper use of this device. This manual is property of the end user. It must be left in their possession upon installation. Always disconnect power prior to performing service on this system. PARTS LIST INTRODUCTION Product Overview Item Part No. Description Quantity Retail Price 10 DL-010 7-Pin Keypad 1 $90.
6 (Serial #) (Revision Letter) 6 Wiring 3 Knock-Out 3 (Current PAC) 3 Page 12 Page 1 INSTALLATION TROUBLESHOOTING Mounting the System Troubleshooting Tips The following guidelines should be followed when mounting the system: Symptom 1. Carefully remove the front faceplate and circuit board from the back box to prevent damage to the electronics. Solution Keypad is 1. Check power. Must have 12 VAC or 12 VDC Dead 2. Check the keypad connection. System Will 1. Check power.
Powering the System It is important to properly power the system with a good power source. To properly power the system: Factory Settings Listed below are the factory settings for the Digi-Lock: 1. Provide power from a dedicated source. 2. Use the 12 VAC, 20va transformer supplied with the system. 3. Use the following guide to determine the proper wire size based upon the distance from power source to the system.
Digi-Lock Power 12V 3. Press 4 Magnetic Lock Control 4. Press (new PAC) Magnetic Lock Common 5. Press # Normally Closed Response BEEP! 6. Press 0 Then Response BEEP! Power BEEP! 1. Connect NC1 to the Magnetic Lock power source. 2. Connect COM1 to the Magnetic Lock Common Input. 3. Connect power source to Magnetic Lock power input. 3. As shown, a separate power supply must be used to power the Magnetic Lock.
ground screw in the Digi-Lock. The Digi-Lock may accept four or five digit entry codes. 4-Digit codes are faster to enter Time Clock Feature and program, but 5-Digit codes offer better security. The system is factory set to A time clock may be installed and used in conjunction with the Digital Lock. This will allow certain entry codes to become valid only during designated times. The time clock must provide a dry contact closure. To install a timer or clock: 4-Digit entry codes.
1. Press # # 2. Press 0 0 # Slave Board Response BEEP! 0 0 0 0 0 (or new PAC) (Sold Separately) BEEP! Master Board 3. Press 2 Slave Light Bulb 12 VAC to Slave Light Bulb only 4. Press PROGRAMMING (Number of Seconds 002 to 240) The next five pages will explain how to program the system. If you find yourself 5. Press # confused in the middle of a program step, simply remove power from the unit, wait Response BEEP! 6.
CAUTION! This step will clear the entire entry code memory. 7. Press # Response BEEP! BEEP! 1. Press # # 2. Press 0 0 # NOTE: To add additional entry codes, repeat steps 3 - 7, otherwise continue. 8. Press 0 Then Response BEEP! # BEEP! Response BEEP! BEEP! 0 0 0 0 0 1 0 (or new PAC) BEEP! PROGRAM COMPLETE 3. Press 7 4. Press 1 5.
