Manual

9100-065-Z-3-13
31
KEY SWITCH
4602
NC
NO
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
“Optional” REVERSE GATE for
Closing Direction Photo Sensors
Functions ONLY during gate closing cycle.
SW 2, switch 2: After photo sensor beam
gets obstructed:
OFF Setting - REVERSES GATE.
ON Setting - Stops gate then continues
closing when gate is clear (Same function
as UL 325 terminal #2).
Note: The ON setting is used to help prevent tailgating
but the photo sensor should be wired to the UL 325
terminal #2 when the “stop gate” function is desired,
see page 27 for more information.
5.2 Control Wiring for Single/Primary Operator
ON
1 2 345678
SW 2
Red Full Open
Green Close
White Com
Key Switch
Stand-Alone
Keypad
Stand-Alone
Card Reader
Telephone
Entry
Fire Box
3-Button Control Station DoorKing ONLY
Note:
All stand-alone and
telephone entry
devices must use a
separate power
source.
#4-Connected device fully opens gate.
#5-Connected device opens gate 14-feet.
#2-Fully opens gate.
Com
Com
Com
Relay -
#2 - Fully opens gate.
#5 - Opens gate 14-feet.
Relay N.O. - #2 - Fully opens gate.
#5 - Opens gate 14-feet.
250 mamp.
max.
3-Wire Radio
Receiver
ON
123 45678
SW 2
SW 2,
switch 3
must be
OFF.
Relay Com
24 Volt Com
24 Volt - 250 mamp. max.
4-Wire
Receiver
#5 Terminal Note (Single Operator Only):
Any opening device connected to terminal #5
will open the gate to the partial open 14-ft setting.
Secondary entrapment protection devices will also
open the gate to the partial open setting. If the
Inherent Reverse Sensor gets activated during the
close cycle, it will always fully open the gate.
24 volt
ON
ON
R
EVERSE
S
E
N
SITIVIT
Y
R
EV
ER
SE
LOO
P
EXIT
L
O
OP
KEY
SWITC
H
DOOR
K
I
NG
4602-01
0
SW
1
S
W
2
O
P
E
N
T
I
M
ER
NC
1
2
3
4
5
NO
WA
RNI
N
G
MOVI
NG
GA
T
E
C
AN
C
A
U
S
E
O
p
e
r
a
t
e
g
a
te
o
n
l
y
w
h
e
n
g
a
t
e
a
r
e
a
i
s
i
n
s
i
g
h
t
a
n
d
f
r
ee
o
f
p
e
o
p
l
e
a
n
d
o
b
s
tr
u
c
t
i
o
n
s
.
D
o
no
t
a
l
l
o
w
c
h
i
l
d
re
n
t
o
p
l
a
y
i
n
g
a
t
e
a
re
a
o
r
o
p
e
r
a
t
e
g
a
t
e
.
D
o
n
o
t
s
t
an
d
i
n
g
at
e
p
a
t
h
o
r
w
a
l
k
t
h
r
o
u
g
h
p
a
t
h
w
h
i
l
e
g
a
t
e
i
s
mo
v
i
n
g
.
Re
ad
o
w
n
e
r
’
s
ma
n
u
al
a
n
d
s
a
f
e
t
y
i
n
s
t
r
uc
t
i
o
n
s
.
S
ER
I
O
U
S
IN
J
UR
Y
O
R
D
EA
T
H
CL
A
S
S
CE
R
T
I
FIE
D
T
O
C
AN
/
C
S
A
C2
2
.2
N
O.
2
4
7
C
O
N
F
O
R
M
S
T
O
AN
S
I
/
V
E
HI
C
U
L
A
R
G
ATE
O
P
E
R
A
TO
R
H
P
5
3
3
8
2
M
O
DE
L
S
ER
I
A
L
V
O
L
T
SP
HA
S
E
A
M
P
S
6
0
H
z
M
A
X
G
A
T
E
L
OA
D
D
o
orK
in
g,
I
nc
.,
I
n
gl
ew
oo
d,
C
A
Full Open
Full Open
Partial Open
Important: Controls intended for user activation must be located at least six (6) feet away from any moving part of the gate and where the user
is prevented from reaching over, under, around or through the gate to operate the controls.
Emergency access controls only accessible by authorized personnel (e.g., fire, police, EMS) may be placed at any location in the line-of-sight of
the gate.