BYAN SYSTEM, INC. 413 LINDEN LUSK, WY 82225 (800) 223-2926 MODEL 800A/900B SERIES VEHICULAR SWING GATE OPERATOR INSTALLATION AND TECHNICAL MANUAL BYAN SYSTEMS, INC. OF LUSK, WYOMING, DEMANDS THAT YOU AS AN INSTALLER INFORM YOUR CUSTOMER OF ALL SAFETY EQUIPMENT THAT SHOULD BE INSTALLED ON EACH JOB SITE. THIS IS IN ACCORDANCE WITH YOUR LEGAL LIABILITY TO YOUR CUSTOMER. ENSURE THAT THE PROTECTION AND WARNING SIGNALING DEVICES ARE OPERATIONAL AND VISIBLE.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products TABLE OF CONTENTS DESCRIPTION PAGE NO.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products USAGE CLASSES FOR VEHICULAR GATES CLASS I – RESIDENTIAL VEHICULAR GATE OPERATOR A VEHICULAR GATE OPERATOR (OR SYSTEM) INTENDED FOR USE IN A HOME OF ONE TO FOUR SINGLE FAMILY DWELLING, OR A GARAGE OR PARKING AREA ASSOCIATE THEREWITH.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products 800A/900A SERIES TECHNICAL DATA MODEL 800A: MODEL 900B: ELIMINATOR SERIES 220 VAC SINGLE PHASE 115 VAC SINGLE PHASE BUILT-IN THERMAL OVERLOAD CAPACITOR RATING: 10UF FOR THE 800A 35UF FOR THE 900A STANDARD WORKING PRESSURE: MAXIMUM WORKING PRESSURE: 1350 PSI 1750 PSI PUMP: SPUR GEAR 1.0 LTR/MIN.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products BEFORE INSTALLATION 1. VERIFY THE GATE POST IS PLUM AND GATE LEAF SWINGS FREELY. 2. PERFORM ANY REQUIRED MAINTENANCE BEFORE CONTINUING. 3. VERIFY THE COMMERCIAL POWER CIRCUIT BREAKERS ARE ISOLATED AND RATED FOR THE SPECIFIC LOAD. VISUALLY ENSURE THE CIRCUIT BREAKERS ARE IN THE “OFF” POSITION AND MARK THE BREAKER USED. 4. IF ANY PRE-CONSTRUCTION WIRING HAS BEEN INSTALLED, VISUALLY INSPECT AND CONFIRM PROPER SIZING AND COMPLIANCE TO CODE. 5.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products INSTALLATION COMPLETION 1. INSTALL PLACARDS AND SAFETY EQUIPMENT AND TEST. 2. “REMOVE” ALL DEBRIS AND OBSTRUCTIONS FROM THE TRAVEL PATH OF THE GATE LEAF(S). 3. TURN ON AND LABEL THE COMMERCIAL POWER CIRCUIT BREAKER AND REMOVE THE “USED” TAG YOU INSTALLED AT THE BEGINNING OF THE PROJECT. 4. USING THE MANUAL BYPASS, POSITION THE GATE LEAF AT 45 DEGREES. PRESS THE TEST BUTTON ON THE G2M CONTROL BOARD. THE FIRST SIGNAL WILL ALWAYS BE TO OPEN.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products INSTALLING THE OPERATOR ! ADVISORIES! A. THIS LINEAR ACTUATOR MUST ME MOUNTED SO THE PISTON FULLY EXTENDS AND FULLY RETRACTS. WHEN FULLY RETRACTED THERE SHOULD BE 1/8 INCH PISTON LEFT OUT OF THE FRONT. B. THIS LINEAR ACTUATOR HAS AN OFFSET BETWEEN THE FRONT AND REAR MOUNTING BRACKET. THE FRONT BRACKET IS ABOUT 5/8 OF AN INCH LOWER THAN THE FRONT BRACKET; REVIEW THE BRACKET ALIGNMENT DETAIL FOR THE OFFSET DIMENSION.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products 12. CONNECT THE CORD PER THE ELECTRICAL CONNECTION DETAILS. NOTE: IT IS HELPFUL TO INSTALL A SINGLE GANG WEATHER PROOF BELL BOX ON THE GATE POST ACROSS FROM THE OPERATOR. THEN WIRE FROM THE CONTROL BOX CAN BE PULLED TO THIS POINT AND CONNECTED TO THE S.O. CORD INSIDE THE BELL BOX.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products HYDRAULIC FLUID BYAN SYSTEMS OPERATORS US A “SHELL OIL PRODUCTS” TELLUS T-15, THIS FLUID HAS A RELATIVELY LOW VISCOSITY SO IT WILL START TO FLOW QUICKLY ON COLD DAYS. WHEN THE FLUID RISES TO OPERATING TEMPERATURE, THERE IS NO RUSH OF THIN FLUID CAUSING POOR HYDRAULIC PERFORMANCE, OR WORSE YET, EXCESSIVE PUMP WEAR, FAILURE AND EXPENSIVE DOWNTIME.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products MANUAL BYPASS THE MANUAL BYPASS VALVE IS FOR THE ABILITY TO RELEASE THE OPERATOR IN THE EVENT OF A POWER FAILURE OR MALFUNCTION. IT IS LOCATED UNDER THE KEYED CAP ON TOP OF THE OPERATOR. A METRIC ALLEN WRENCH IS SUPPLIED IN THE CAP TO RELEASE THE BYPASS VALVE. TURN THE VALVE COUNTER CLOCKWISE UNTIL THE OPERATOR RELEASES. WHEN TIGHTENING THE BYPASS VALVE IT MUST BE TIGHT IN ORDER TO PREVENT FLUID OR PRESSURE ESCAPING BACK INTO THE CHAMBER.
BYAN SYSTEMS, INC.
BYAN SYSTEMS, INC.
BYAN SYSTEMS, INC.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products RECOMMENDED WIRE SIZES HIGH VOLTAGE A.C. 14 AWG TO 400 FEET 12 AWG TO 650 FEET 10 AWG TO 1000 FEET 8 AWG TO 1650 FEET 6 AWG TO 2650 FEET LOW VOLTAGE A.C. 18 AWG TO 100 FEET 16 AWG TO 170 FEET 14 AWG TO 270 FEET 12 AWG TO 430 FEET 10 AWG TO 690 FEET 8 AWG TO 1100 FEET LOW VOLTAGE D.C.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products G2M CONTROL BOARD DESCRIPTION G2M-115V/220V SINGLE PHASE MICRO CONTROLLED BOARD THIS ELECTRONIC CONTROL UNIT IS SUITABLE FOR SINGLE-PHASE MOTORS, AND CAN DRIVE UP TO TWO DIFFERENT MOTORS. THERE IS LEAF DELAY INCORPORATED WITH THE USE OF A PLUG IN CARD. 9 DIP SWITCHES CAN SELECT SOME DIFFERENT OPTIONS OF THE CONTROL UNIT. THERE ARE THREE POSSIBLE TIMING POTENTIOMETERS: OPENING TIME, AUTOMATIC CLOSING TIME, AND THE CLOSING TIME.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products CLOSING BUTTON: USED ONLY TO CLOSE THE GATE. STOP BUTTON: (NORMALLY CLOSE CONTACT), STOPS THE GATE IN OPENING/CLOSING. THREE ADJUSTABLE TIMES BLUE TIMER: OPENING TIMER ONLY CONTROLS THE OPENING TIME BETWEEN 3 TO 30 SECONDS. RED TIMER: CLOSING TIMER ONLY CONTROLS THE CLOSE TIME BETWEEN 3 TO 30 SECONDS.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products DIP SWITCH ASSEMBLY OPERATION MODE SELECTION; No.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products SELECTABLE OPTIONS SWITCH S3 No. 1 OPTION EXTENDS RUN TIME 2 REPOSITIONING THE DOOR * ON OPENING AND CLOSING TIME (30 SECONDS TO 1 MINUTE) ACTIVE OFF OPENING AND CLOSING TIME (3 SECONDS TO 30 SECONDS) INACTIVE * WITH THIS OPTION ACTIVE AND THE DOOR CLOSED THE DOOR IS CLOSED FOR 2 SECONDS EVERY HOUR, AND IF THE DOOR IS OPENED THE DOOR IS OPENED FOR 2 SECONDS EVERY HOUR. TERMINAL BOARD POWER TERMINALS (FROM TOP TO BOTTOM) 1. POWER SUPPLY 2.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products CONTROL CONTACT TERMINAL DESCRIPTION 1 ENTRAPMENT ALARM OUTPUT 2 ENTRAPMENT ALARM OUTPUT 3 24VAC OUTPUT @ 1 AMP MAX. 4 24VAC OUTPUT @ 1 AMP MAX.
BYAN SYSTEMS, INC.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products SECOND MOTOR CARD T2M CHARACTERISTICS: THIS CARD IS SUITABLE FOR DRIVING A SECOND MOTOR THROUGH THE CONTROL UNIT, SELECTING THE OPENING DELAY TIME AND THE CLOSING DELAY TIME BETWEEN THE TWO MOTORS. THE LIMIT SWITCHES OF THE SECOND MOTOR SHOULD BE CONNECTED TO THIS CARD. THESE SIGNAL INPUTS ARE OPT-COUPLED TO PREVENT MALFUNCTION DUE TO INTERFERENCE OR ATMOSPHERIC DISTURBANCES. THE CONTROL UNIT POWERS THE CARD.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products LOOP DETECTOR CONNECTIONS THE MOLLEX CONNECTOR HAS 11 WIRE LEADS 12 INCHES LONG.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products TO THE INSULATION? THE OUTER DIAMETER IS 0.115” FOR 14 GA. WIRE AND 0.013” FOR 16 GA. WIRE. WHEN INSTALLED IN A ” (0.250) SLOT, AS IS OFTEN DONE, THE TURNS OF WIRE CAN LAY SIDE BY SIDE IN THE SLOT AND THE TURNS TWIST UNDER THE PRECEDING TURNS AND NOT STACK SNUGLY IN A SINGLE LAYER, AS THEY SHOULD BE. THIS WILL CAUSE REDUCED LOOP EFFICIENCY.
BYAN SYSTEMS, INC.
BYAN SYSTEMS, INC.
BYAN SYSTEMS, INC.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products FOUR YEAR LIMITED WARRANTY This warranty pertains only to products manufactured for/or by Byan Systems, Inc. for gate operating systems, accessories, and equipment. These products are warranted against all defective material for forty-eight months from the date of sale. Defective material returned must be prepaid and accompanied by a Byan Systems, Inc.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products END USER SAFETY “THE GATE AUTOMATION AND ACCESS CONTROL MANUFACTURER” HAS NO CONTROL OVER THE GATE SYSTEM YOU HAVE AUTOMATED. THE WORD “SYSTEM” HEREIN REFERS TO THE GATE POST, GATE LEAF, HINGING, ALL AUTOMATION EQUIPMENT, ACCESSORY DEVICES, THE CONSTRUCTION AND INSTALLATION THEREOF. VEHICULAR GATE OPERATING SYSTEMS PROVIDE CONVENIENCE AND SECURITY TO THEIR USERS.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products PROTECTION DEVICES IN THE AREA, ON THE GATE, OR THE EQUIPMENT ITSELF. 4. “CAUTION!!!” NEVER ALLOW CHILDREN TO RIDE ON THE GATE(S) OR PLAY AROUND THE ELECTRICAL ENCLOSURES 5. NEVER OPERATE A GATE SYSTEM WITHOUT VISUAL CONTACT SO IT CAN BE SUSPENDED IF NECESSARY. 6. SECURE AND LABEL POWER CABINETS OR EQUIPMENT COVERS. 7.
BYAN SYSTEMS, INC. Automated Gate and Access Control Products CUSTOMER ACKNOWLEDGMENT DEAR _________________________________ (CUSTOMER/COMPANY NAME) VEHICULAR GATE OPERATING SYSTEMS PROVIDE CONVENIENCE AND SECURITY TO THEIR USERS. BECAUSE THESE MACHINES PRODUCE SUCH HIGH LEVELS OF FORCE, ALL GATE OPERATING SYSTEM DESIGNERS, INSTALLER AND END USERS NEED TO BE AWARE OF THE POTENTIAL HAZARDS ASSOCIATED WITH IMPROPERLY DESIGNED, INSTALLED OR MAINTAINED SYSTEMS.
