User's Manual

ManualsBrandsControlled Entry Distributors ManualsElectronicsCARD READER

Table Of Contents

10.2 Door setting

Fail secure

(Unlocked when power on)

4 0 99 #

0-99 is to set the door relay time 0-99 seconds.

Fail safe (unlocked when power is off)

This is the factory default, 5 seconds:

5 0 99 #

0-99 is to set the door relay time 0-99 seconds.

Door open detection

Door Open Too Long (DOTL) warning. When used with an optional magnetic

contact or built-in magnetic contact of the lock, if the door is opened normally, but

not closed after 1 minute, the inside buzzer will beep automatically to remind

people to close the door and continue for 1 minute before switching off

automatically.

Door Forced Open warning. When used with an optional magnetic contact or

built in magnetic contact of the lock, if the door is forced open, or if the door is

opened after 120 seconds of the electro-mechanical lock not closed properly,

the inside buzzer and alarm output will both operate.

To disable door open detection.

(Factory default)

6 0 #

Security Mode Setting

Read er Lockout & Alarm Output options. If there are 10 invalid cards in a 10

minute period, the Reader will lockout for 10 minutes or the alarm will

operate for 10 minutes, depending on the option selected below.

Normal status (No lockout or alarm)

7 0 # (Factory default setting)

Reader Lockout

To Unlock the door

7 1 #

Alarm Output

7 2 #

Door Interlock.

Door interlock disabled

Door interlock enabled

8 0 #

8 1 #

Alarm output time

To set the alarm output time (0-3

minutes) Factory default is 1 minute

9 0~3 #

To remove the alarm

To remove the door forced open warning

Read valid card or Master Code #

To remove the door open too long

warning

Close the door or Read valid card

or Master Code #

Read user card (Note that Manager Card can't

be used to unlock the door.)

Attach: Advanced Application

1. W2 operating as a Controller

In this mode the W2 supports a Wiegand 26 bit input so an external Wiegand device

with a 26 bit output can be connected to the Wiegand input terminals on the W2.

Either an ID card reader (125 KHZ) or an IC card reader (13.56MHZ) can be

connected to the W2. Cards are required to be added at the external reader, except

where an external EM reader is used, in this case cards can be added at either

reader. See figure 1

figure 1

+12V

GND

Lock

Em card

HID card

Ic card

DC12V/3A

Power

ALARM-

OPEN

D_IN

+12V

GND

VSS

L-

L+

ALARM+

Green

White

Grey

Yellow

Brown

Red

Black

Blue

Purple

Orange

wiegand reader

reader plug

W2 controller

Alarm

Exit button

door detecting switch

2. W2 operating as a Wiegand Output Reader

In this mode the W2 supports a Wiegand 26 bit output so the Wiegand data lines can

be connected to any controller which supports a Wiegand 26 bit input. See figure 2

ALARM+

White

Grey

Yellow

Brown

Red

Black

Blue

Purple

Orange

Powerful supply

Controller with wiegand 26 input

+12V

GND

Controller

Green

ALARM-

OPEN

D_IN

+12V

GND

VSS

L-

L+

figure 2

3. Two W2 units interconnected for a single door

In this mode two W2 units are used for a single door, one for entry and the other for exit.

Either device acts as the controller and reader at the same time. Users can be

enrolled oneither of the devices. In this mode the user capacity for one door can

be up to 20000. The setting of the two W2 units must be the same including the

master code. See figure 3

Exit button

Lock

door detecting switch

Alarm

DC12V/3A

Power

indoor

outdoor

ALARM-

OPEN

D_IN

+12V

GND

VSS

L-

L+

ALARM+

Green

White

Grey

Yellow

Brown

Red

Black

Blue

Purple

Orange

ALARM-

OPEN

D_IN

+12V

GND

VSS

L-

L+

ALARM+

Green

White

Grey

Yellow

Brown

Red

Black

Blue

Purple

Orange

W2 controller 2W2 controller 1

figure 3

4. Two W2 units interconnected & interlocked for 2 doors

In this mode two W2 units are used for a two doors which are then interconnected

and interlocked. In this mode the doors can be interlocked so that when door 1 is

open, door 2 cannot be opened, and vise versa. The interlocked function is mainly

used in banks, prisons, and other places where a higher level of security is required.

See figure 4

door detecting switch 1

Lock 1

DC12V/3A

Power

W2 controller 2

Door 2

Alarm 2

Alarm 1

Lock 2

Exit button 1

door detecting switch 2

Exit button 2

Door 1

W2 controller 1

ALARM-

OPEN

D_IN

+12V

GND

VSS

L-

L+

ALARM+

Green

White

Grey

Yellow

Brown

Red

Black

Blue

Purple

Orange

ALARM-

OPEN

D_IN

+12V

GND

VSS

L-

L+

ALARM+

Green

White

Grey

Yellow

Brown

Red

Black

Blue

Purple

Orange

figure 4

5. Anti-submarine function for single door (3 1 #)

The connection diagram is as figure 1. Install one Wiegand reader (or a W2

without user information as reader) outside the door, connecting to one W2-

Controller inside the door, which acts as the Anti-submarine Master unit. Of the

two devices, they build up an anti-submarine system for single door. The

operation and function is as below:

5.1 Set the needed function and enroll the User Cards on the inside W2 - Anti-

submarine Master unit.

5.2 With the valid user card, the user can only enter the door from the outside

reader, and exit from the inside W2 Controller. On the other hand, without

entering record from the reader, the user can't exit from the controller inside,

also, the user can't enter in and exit twice continuously.

6. Anti-submarine function for 2 doors

The connection diagram is as Figure 4. Door 1 with one W2, and Door 2 with

one W2, set one W2 on Door 1 as the Anti-submarine Auxiliary unit (3 2 #), and

set the other W2 on Door 2 as the Anti-submarine Master unit(3 1 #). They build

up a two doors anti-submarine system, which is normally used for parking

lot......etc

The operation and function is as below:

6.1 Set the needed function and enroll the User Cards from W2 - Anti-submarine

Master unit on Door 2.

6.2 With the valid user card, the user can only enter in from Door 1, and exit from

Door 2. On the other hand, without entering record from the Auxiliary unit, the

user can't exit from the Master unit or Auxiliary unit , also, the user can't enter in

and exit twice continuously.

.9. .10. .11.

.6. .7. .8.

Lock Power Setting

Anti-submarine Settings

Anti-submarine Disabled

Anti-submarine Master Mode:

Antisubmarine Auxiliary Mode

(Note: the detailed wiring diagram and illustrate,please refer to the Advanced application ) .

(Factory default)

3 0 #

3 1 #

3 2 #

To enable door open detection

6 1 #

To Unlock the door