User's Manual

ManualsBrandsControlled Entry Distributors ManualsElectronicsCARD READER

Table Of Contents

I/O

ALARM-

R20

Lock Interface Principle:

By programme setting, I/O

switch between low level and

high level.

4-low level

5-high level

I/O

L-

L+

+12V

R19

Alarm Interface Principle:

when alarm, the I/O outputs high level.

The W2 is fully waterproof Proximity stand alone access Reader, which uses

advanced microprocessor, equipped with large capacity Flash memory,

supports up to 10 000 cards. It is so easy to add or delete card users by using the

master card, besides, with Infrared remote control programmer, the user can set

the features by themselves, including Alarm, Self-protection, interlock and Anti-

submarine back Function. In additional, with infrared remote control

programmer, you can add or delete cards directly by inputting card number

The W2 not only has the features of low power consumption, automatic selection

of lock ,anti vandal alarm and exit button, but also has the protective functions

against input over voltage and outputs short-circuit. These features make the W2

safe , reliable and easy in operation. It is an idea choice for door access.

2.Description

Standalone Card Reader

Use capacity: 10,000

Card interface: 125KHZ EM card

Remote control for programming

With Manager cards for fast add

and delete users

Wiegand26 input/output

3.Features

4. Specifications

Supply Voltage

Sleeping Current

Card type

Card Reading Distance

Wiegand interface

Temperature

20% 98%

Max20A

Two

103*48*23mm

Drill holes on the wall or prepare the cassette.

Wire through the hole, and blanket the unused

cable in case of short circuit.

Fix the back cover firmly on the cassette or the wall.

Attach the reader to the back cover.

5. Installation

6. Wiring

Color

Yellow

Blue

Brown

Purple

Grey

Red

Black

White

Green

Orange

Function

ALARM+

OPEN

D_IN

12V

GND

VSS

L-

L+/Alarm+

Description

Wiegand output, input signal wire D0

Wiegand output, input signal wire D1

connecting to the negative pole of the alarm equipment

To connect to one part of Exit Button

Door Contact input

(+) 12Vdc Positive Regulated Power Input

(-) Negative Regulated Power Input

the negative pole of the controller, connect to the other

part of Exit button and door contact

Connect to the negative pole of the Lock

Connect to the positive pole of the lock and alarm equipment

Connection Diagram

7. Interface Circuits

Figure 1

Note: The above diagrams show the output interface circuits.

Do not power on until all wiring has been completed

Power off, use the supplied Contact Pin to short out the 2P socket on the

mainboard, then power on, if successful, the beeper will beep twice, the LED

shines in orange, remove the Short Pin, then read any two EM cards, after that

the LED turns in red, means reset to factory default setting successfully. Of the

two EM cards read, the first one is Manager add card, the second one is

Manager delete card.

Remarks: Reset to factory default setting, the users' information enrolled is still

retained. When reset to Factory setting, the two Manager cards must be re-enrolled.

8.To Reset to Factory Default and Manager Card setting

9. Sound and Light indication

Operation status

Reset to factory default setting

Sleeping mode

Operation successful

Enter into programming mode

Enter into setting

Exist from programming mode

Operation failed

Open the door

Alarm

LED

Orange

Red shines slow

Red shines

Orange shines

Red shines slow

Green shines

Red shines fast

Buzzer

Two short ring

Short ring

Three short ring

Short ring

Alarm

10. W2 Detailed Programming Guide

10.1User settings

There are 2 ways to add and delete users:

A - By manager card; B - By remote control

A - By Manager card(The most convenient way)

To Delete User by Manager Card

B- By Remote control

Enter into the programming mode firstly

To Enter the programming mode

Manager add card Read user card Manager

add card Cards can be added continuously.

Manager delete card Read user card Manager

Delete ca rd Cards can be deleted continuously.

* Manager Password #

888888 is the default factory master code

To Add user by Manager Card

Remarks: All the steps below must be done after enter into programming mode

To change the master code

0 New Password # Repeat New Password #

The master code must be 6 8 digit number.

To add a card user (Method 1)

This is the faster way to enter

cards using ID number auto

generation. The card can be

either be presented or input the

8 digit card number from the

card can be manually entered

1 Read Card # or

1 Input Card number (8 digit) #

Card can be added continuously without

exiting programming mode.

The card number is the last 8 digits of the

number printing on the card.

DC12V/3A

Lock

Exit button

Alarm

door detecting switch

Common Power Supply

ALARM-

OPEN

D_IN

+12V

GND

VSS

L-

L+

ALARM+

Green

White

Grey

Yellow

Brown

Red

Black

Blue

Purple

Orange

ALARM-

OPEN

D_IN

+12V

GND

VSS

L+

ALARM+

DC12V/3A

COM

PUSH

L-

Green

White

Grey

Yellow

Brown

Red

Black

Blue

Purple

Orange

door detecting switch

Exit button

Alarm

Fail-securelock

Fail-safe lock

Special Power Supply

W2 - Waterproof

Standalone Proximity Reader

Shielded

cables

61mm

95.5mm

40mm

To add a card user(Method 2)

This is the alternative way to

enter cards using User ID

Allocation. In this method a User

ID is allocated to a card. Only

one user ID can be allocated to a

single card.

1 ID number # Read Card # or

1 ID number # the Card number (8 digits) #

To delete a card user by card Number.

Note users can be deleted continuously

without exiting programming mode

2 Read Card # or

2 Card number #

To delete ALL users.

(Note: This option will delete all users

but Manager Cards. Be careful with use)

2 0000 #

.4. .5. .6.

Can be used as salve reader

2 pcsW2 can be interconnected/ interlocked

Can be used as controller by connection

slave reader

Anti-submarine back Function

Alarm signal output, Door open detection

Full of 10000 users, recognizing speed <15ms.

1. Packing List

Name

Standalone Proximity Reader

Infrared remote control

Manager card

Short Pin

User manual

Self Tapping Screws

Specification

One for add, one for delete

Used for factory default setting

3.5*27mm

Quantity

4/2

Humidity

Lock output load

Alarm output load

Manager card

Dimensions

DC12V 10%

<15mA

125KHZ EM card

5 10cm

Wiegand 26

-20 60

.1. .2. .3.

Summary of content (3 pages)

PAGE 1
4. Specifications Name Standalone Proximity Reader Infrared remote control Manager card Short Pin User manual Self Tapping Screws Specification W2 One for add, one for delete Used for factory default setting W2 3.5*27mm Quantity 1 1 2 1 1 4/2 2.Description The W2 is fully waterproof Proximity stand alone access Reader, which uses advanced microprocessor, equipped with large capacity Flash memory, supports up to 10 000 cards.
PAGE 2
10.2 Door setting Lock Power Setting Fail secure (Unlocked when power on) 4 0 99 # 0-99 is to setthe door relay time0-99 seconds. Fail safe (unlocked whenpower is off) This is the factorydefault, 5 seconds: 5 0 99 # 0-99 is to setthe door relay time0-99 seconds. Reader Lockout 7 1 # Alarm Output 7 2 # Anti-submarine Disabled 3 0 # Anti-submarine Master Mode: 3 1 # Antisubmarine Auxiliary Mode 3 2 # Door interlock disabled 8 0 6 To enable door open detection 6 0 Advanced application ) .
PAGE 3
FCC WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.