User's Manual

CEM emerald
Terminal product codes
Intelligent Fingerprint
Warnings
Warning
This is a class B product. In a domestic environment this product may
cause radio interference in which case the user may be required to
take adequate measures
Warning
English
Under Industry Canada regulations, this radio transmitter may only
operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada.
To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
Français
Conformément à la réglementation d'Industrie Canada, le présent
émetteur radio peut fonctionner avec une antenne d'un type et d'un
gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie
Canada.
Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et
son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une
communication satisfaisante.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est suscep-
tible d'en compromettre le fonctionnement.
Warning - For FCC Labelled emerald Terminals
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept an interference received, including
interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. End users must follow the specific
operating instructions for satisfying RF exposure compliance. This
transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
Installation of this device shall be performed by a qualified person in
accordance to all local regulations.
This system must be installed within the protected premise in accord-
ance with the National Electrical Code (NFPA70), and the local
authorities having jurisdiction.
Equipment changes or modifications without the approval of the party
responsible for compliance could void the user's authority to operate
the equipment and could create a hazardous condition.
CARD READ
TECHNOLOGY
TS100F TS200F TS300F
FCC ID NUMBER
IC ID NUMBER
Mifare CSN TSR/100/115
Picopass
CEM DESFire
iClass &
iClass SE
multi smart
card reader
TSR/100/116
TSR/100/117
TSR/100/118
TSR/100/618
TSR/200/115 TSR/300/115
TSR/200/116 TSR/300/116
TSR/200/117 TSR/300/117
TSR/200/118 TSR/300/118
TSR/200/618 TSR/300/618
QABTSR618V93F
12009A-TSR618V93F
QABTSR618V93F
12009A-TSR618V93F
QABTSR618V93F
12009A-TSR618V93F
QABTSR618V93F
12009A-TSR618V93F
QABTSR618V93F
12009A-TSR618V93F
Note: The typical read range for the integrated 13.56MHz
read-head is 3 – 5cm (1.2” – 2”)
Supported card technologies
The emerald Intelligent Fingerprint Terminal multi smart card
reader supports the following card technologies:
• CEM DESFire
• MIFARE CSN
• iClass